Thank you for choosing CME UF Professional Master MIDI Keyboard with Built-in USB Please keep all the important information here Attach your invoice or receipt here ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ for reference Purchase date Dealer's name and addr. Serial(on the back of the keyboard) Dealer's tel. Warning: Improper connection may cause damage to the device. Copyright: Copyright of the manual belongs to Central Music Co.
PRECAUTIONS IMPORTANT Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, damages, fire or other hazards. These precautions include, but are not limited to, the follows: 1. Read and understand all the instructions. 2. Always follow the instructions on the instrument. 3.Before cleaning the instrument, always remove the electric plug from the outlet as well as the USB cable. When cleaning, use a soft, dry cloth.
Keep this manual in safe place CAUTION: Setting up Do not connect the instrument when thundering. Do not set up the cord or outlet to moisture place, except for that the outlet is specially designed for moisture. When the power cord is connected to the AC outlet, do not touch the naked part of cord or connector. Always follow the instructions carefully when setting up the instrument. WARING: Do not expose the instrument to rain or moisture, to avoid fire or electrical shock.
Contents Contents 1.Connection ............................................................ 5 1.1 Front panel ................................................................................. 5 1.2 Rear panel ................................................................................. 6 1.3 Connect UF to tone generators ................................................. 7 1.4 Add UF to computer music system ........................................... 8 1.5 Driver installation ..........................
Connection 1.Connection 1.1 Front Panel Sequencer remote control Those buttons are used to control external sequencer. Voice editing knobs 8 assignable knobs with preset for voice editing. Volume Faders 8 assignable faders (sliders) with preset for channel volume. Master Volume Master volume fader for external tone generator (GM standard.) Knob Func This button is used to switch knob function. Fader Func This button is used to switch fader function.
Connection 6 1.2 Rear panel MIDI OUT All the MIDI messages from the UF keyboard or from USB transmission will be outputted to external MIDI devices via MIDI OUT terminal. SUSTAIN PEDAL A sustain pedal can be connected to SUSTAIN PEDAL terminal. The sustain pedal will generate MIDI controller #64 message. CONTROLLER PEDAL A controller pedal can be connected to CONTROLLER PEDAL terminal.
Connection USB cable for bi-direction data transmission. CABLE HOOK Keep the power cord in the CALBE HOOK when necessary for good power connection. POWER INLET Power supply goes from the A.C. adapter to the POWER INLET. POWER SWITCH POWER SWITCH is used to turn on or turn off the UF keyboard. 1.3 Connect UF to tone generators Warning: Turn off all the devices before connection Connect UF to a tone generate then you can play 1.3.1 Connect UF MIDI OUT to tone generator MIDI IN via MIDI cable 1.3.
Connection (included with UF8), Controller pedal, or Breath Controller(such as YAMAHA BC3). 1.3.6 Now you can play the tone generator with UF keyboard. 1.4 Add UF to computer music system You can add UF keyboard to the computer music system, then you can use UF as the master MIDI keyboard of the system to play music as well as input other MIDI messages. 8 1.4.1 Connect UF USB port to your computer USB port via the USB cable supplied with the UF keyboard. 1.4.
1.5 Driver installation 1.5.1 Connect UF to computer via USB cable 1.5.2 Power on the computer 1.5.3 Insert UF CD-ROM to computer 1.5.4 Follow instructions in the README file to finish the installation. Play the instrument Hint: You can also use MIDI cable to connect UF keyboard to computer music system via a MIDI interface, in this way you do not have to make USB connection, nor to install USB driver.
Play the instrument vate reset function. 2.3.2 During the reset process, the LCD flashes until reset process is finished. Hint: Reset function will clear all of your settings to the keyboard! 2.4 Value adjustment and display 2.4.1 Data dial Please notice that for current selected function, the value will be displayed on LCD. When you rotate the Data dial, current value will be changed accordingly, and the LCD will display the new value. 2.4.
By rotating the pitch bend wheel when playing the keyboard, you can change the current note pitch. 2.6.1 Pitch bend wheel sends PITCH BEND message. 2.7 Modulation wheel By rotating the Modulation wheel when playing the keyboard, you can add vibration to the sound. 2.7.1 Modulation wheel sends MIDI controller 1# message. Play the instrument 2.6 Pitch bend wheel 2.
Play the instrument When no LED lights for “FADER FUNC.” button, faders function list: Function Channel Controller# Default Value range M.Vol ALL M.volume 127 0-127 Vol.1 1 7 100 0-127 Vol.2 2 7 100 0-127 Vol.3 3 7 100 0-127 Vol.4 4 7 100 0-127 Vol.5 5 7 100 0-127 Vol.6 6 7 100 0-127 Vol.7 7 7 100 0-127 Vol.8 8 7 100 0-127 When upper LED lights for “FADER FUNC.” button, faders function list: Function Channel Controller# Default Value range M.Vol ALL M.volume 127 0-127 Vol.9 9 7 100 0-127 Vol.
2.11 All notes off (ALL NOTES OFF) If the external tone generator produces weird voice(such as continuous long voice), you can push TRANSPOSE and OCTAVE at the same time to send controller 123# to stop all the notes of the tone generator. Hint: If the tone generator does not support controller 123#, or the weird voice is caused by other reasons, this function may not work. Advanced functions make sound. 3. Advanced functions 3.
Advanced functions 2 After new controller number is assigned, release FUNC. button. KNOB Hint For detail about assignable controllers, refer to appendix 5.1 When the LED indicator for “KNOB FUNC.” does not light, knobs function list: Knob Func Controller# Default Value range CUTOFF 74 64 0-127 RESONANCE 71 64 0-127 ATTACK 73 64 0-127 RELEASE 72 64 0-127 PAN 10 64 0-127 REVERB 91 40 0-127 CHORUS TEMPO 93 0 120 0-127 20-250 Hints: 1.
Hint: Some music software may have problem with sysx, so please be careful using this function. Advanced functions Push CHANNEL and SPLIT at the same time, the keyboard will send sysx for GS on (F0 41 10 42 12 40 00 7F 00 41 F7). By sending GS on message, you can make GS initializing for GS compatible tone generators. 3.4 Adjust velocity curve (V.CURVE) V.CURVE button is used to adjust velocity response of the keyboard. You can choose from four preset velocity curves.
Advanced functions 3.5.1 First you should set up voice and channel for the left section. 3.5.2 Push SPLIT button to activate split function, and the keyboard is split to two sections at key #F2(54), which is called the split point. 3.5.3 You can only adjust the voice and channel settings for the right section when split function is on. 3.5.4 To change the split point: push and hold SPLIT button, then press a key in the keyboard to indicate a new split point, the key number will be displayed on the LCD.
3.7 After touch (A.TOUCH) A.TOUCH is the switch for the channel after touch function. 3.7.1 By pushing A.TOUCH button, you can turn on or off the after touch function of the keyboard, to allow or permit the after touch message from the keyboard. Note: This function only works when the keyboard is powered by the AC. Adapter. 3.8 Drawbar organ (DRAWBAR) With the drawbar organ function, you can use fader CS0-CS8 as drawbars to adjust organ voice. 3.8.
Appendix 2.If you press one of the 6 buttons after the keyboard is powered on, the keyboard will start sending MTC(MIDI timing clock). To stop sending MTC, press "Reset" compound, or just turn off then turn on the keyboard. 4.2 Select MIDI route Press “CHANNEL” and “DUAL” at the same time, the current MIDI route status (code) will be displayed on the LED, then we can use DEC/INC button or the data dial to select the MIDI route by its status code.
Data Entry LSB Channel Volume LSB Balance LSB Controller Pan LSB Expression LSB Controller Sustain Portamento Sostenuto Soft Pedal Legato FootSwitch Hold 2 Sound Controller Resonance Release Time Attack Time Cutoff Decay Time Vibrato Rate Vibrato Depth Vibrato Delay Sound Controller Controller Portamento Control Controller Reverb Effects Chorus Effects Effects RPN Increment RPN Decrement NRPN LSB NRPN MSB RPN LSB RPN MSB Controller All Sound Off Reset All Controllers Local Controllesr All Notes Off OMNI Off
Appendix 5.2 Troubleshooting Trouble After turning on the power switch, the keyboard is not powered on Possible reasons and action to solve 1. Make sure you have connect the keyboard to its AC adaptor with proper AC supply 2. If the power is supplied via host USB, please check the USB connection, and make sure that the host computer is turned on. No sound when playing the 1. There is no tone generator in the UF keyboard.
Keyboard UF5: 49 key keyboard (C1-C5), (Initial Touch/After touch) UF6: 61 key keyboard (C1-C6), (Initial Touch/After touch) UF7: 76 key keyboard (A-1-C6), (Initial Touch/After touch) UF8: 88 keys (A-1 - C7), Hammer Effect Keyboard (Initial Touch/After touch) Appendix 5.
Appendix USB) Dimensions (W x D x H)and weights UF5: 859 x 348 x 113 mm, 8.2 kg UF6: 1022 x 348 x 113 mm, 9.8 kg UF7: 1232 x 348 x 113 mm, 11.8 kg UF8: 1408 x 372 x 150 mm, 23.5 kg * Specifications and appearance are subject to change without notice. 5.4 MIDI Implementation Chart Model: UF 5/6/7/8 Function Version: 1.
Name 1394(IEEE1394) A.TOUCH ALL NOTES OFF B.C. CHANNEL CONTROLLER Pedal CS1-CS8 DATA DIAL DEC & INC DEMO DRAWBAR DUAL FADER FUNC. FORWARD GM ON GS ON KN1-KN8 KNOB FUNC. LED MIDI OUT MODULATION OCTAVE PITCH BEND PLAY POWER POWER ON/OFF PROGRAM RECORD RESET REWIND SPLIT STOP SUSTAIN PEDAL TOP TRANSPOSE USB V.
Appendix Trade marks: CME is the registered trade mark of Central Music Co. UF is the registered trade mark of Central Music Co. XG is the registered trade mark of YAMAHA corporation GS is the registered trade mark of Roland corporation GM is the registered trade mark of AMEI. All the other trade marks belong to their respective owners. Limited warranty: All the content and specification in this manual are for reference only.
