Owner's manual

ManualsBrandsCMP ManualsAccessories communicationC2K

INSTALLATION INSTRUCTIONS FOR

INSTALLATION OF CMP CABLE

GLAND TYPE C2K

FOR TERMINATION OF CABLES WITH WIRE BRAID, TAPE ARMOUR (STA/DSTA), STRIP ARMOUR AND

SINGLE WIRE ARMOUR (SWA). FOR USE IN HAZARDOUS AREAS

INCORPORATING EC DECLARATION OF CONFORMITY TO DIRECTIVE 94/9/EC

CMP Document No. FI440 Issue 2 01/13

0518

Notified Body: Sira Certification Service, Rake Lane, Chester CH4 9JN, England.

I, the undersigned, hereby declare that the equipment referred to herein conforms to the requirements of the ATEX Directive 94/9/EC and the

following standards:-

EN60079-0:2006, EN60079-1:2007, EN60079-7:2007, BS 6121:1989, EN50262:1998 (Amd 2001), EN61241-0:2004, EN61241-1:2004

Dr Geof Mood - Technical Director - (Authorised Person)

DUBAI • HOUSTON • NEWCASTLE • SINGAPORE • SHANGHAI • PUSAN • PERTH

www.cmp-products.com

Logo’s shown for illustration purposes only. Please check certification for details

CABLE GLAND

TYPE C2K

able

onnector

ize

Available Entry Threads

hread Length

Cable

edding

iameter

Overall Cable

Diameter

Armour Wire Diameter

Across

Flats

Across

Flats

Protrusion

Length

Ordering Reference

(NP Brass NPT)

PVC

Shroud

Reference

onnector

eight

(

Ozs)

tandard

ption

Grooved Cone Stepped Cone

Metric NPT NPT Actual NPT Min Metric Max Min Max Min Max Min Max Min Max Max Max

20S/16 1/2" 3/4" M20 0.630 0.591 0.461 0.240 0.453 0.006 0.020 0.035 0.049 0.945 1.021 2.303 20S16C2K1RA531 PVC06 4.65

20S 1/2" 3/4" M20 0.630 0.591 0.461 0.374 0.626 0.006 0.020 0.035 0.049 0.945 1.021 2.303 20SC2K1RA531 PVC06 4.65

20 1/2" 3/4" M20 0.630 0.591 0.551 0.492 0.823 0.008 0.020 0.035 0.049 1.201 1.112 2.382 20C2K1RA531 PVC06 6.84

25S 3/4" 1 M25 0.669 0.591 0.787 0.551 0.866 0.008 0.024 0.049 0.063 1.476 1.594 2.657 25SC2K1RA532 PVC09 10.78

25 3/4" 1" M25 0.669 0.591 0.787 0.717 1.031 0.008 0.024 0.049 0.063 1.476 1.594 2.657 25C2K1RA531 PVC09 10.78

32 1" 1 1/4" M32 0.787 0.591 1.035 0.933 1.335 0.008 0.024 0.063 0.078 1.811 2.008 2.736 32C2K1RA532 PVC11 16.49

40 1 1/4" 1 1/2" M40 0.787 0.591 1.268 1.098 1.591 0.008 0.031 0.063 0.078 2.165 1.956 3.071 40C2K1RA534 PVC15 23.89

50S 1 1/2" 2" M50 0.787 0.591 1.504 1.386 1.839 0.008 0.031 0.078 0.098 2.362 2.338 2.972 50SC2K1RA535 PVC18 26.43

50 2" 2 1/2" M50 0.906 0.591 1.736 1.591 2.091 0.012 0.031 0.079 0.098 2.756 2.827 3.169 50C2K1RA536 PVC21 36.79

63S 2" 2 1/2" M63 0.906 0.591 1.969 1.795 2.339 0.012 0.031 0.079 0.098 2.953 3.189 3.602 63SC2K1RA536 PVC23 37.85

63 2 1/2" 3" M63 0.984 0.591 2.205 2.150 2.594 0.012 0.031 0.079 0.098 3.150 3.402 3.622 63C2K1RA537 PVC25 45.11

75S 2 1/2" 3" M75 0.984 0.591 2.441 2.323 2.839 0.012 0.031 0.098 0.118 3.504 3.784 3.898 75SC2K1RA537 PVC28 65.55

75 3" 3 1/2" M75 1.417 0.591 2.677 2.262 3.091 0.012 0.031 0.098 0.118 3.898 4.209 4.016 75C2K1RA538 PVC30 89.87

90 3 1/2" 4" M90 1.417 0.591 3.150 3.000 3.559 0.012 0.031 0.124 0.157 4.488 4.847 4.724 90C2K1RA539 PVC32 128.63

Dimensions are displayed in inches unless otherwise stated

Glasshouse Street • St. Peters • Newcastle upon Tyne • NE6 1BS

Tel: +44 191 265 7411 • Fax: +44 191 265 0581

E-Mail: cmp@cmp-products.co.uk • Web: www.cmp-products.com

TECHNICAL DATA

CABLE GLAND TYPE : C2K

INGRESS PROTECTION : IP66, IP67, IP68

PROCESS CONTROL SYSTEM : BS EN ISO 9001

: ISO/IEC 80079-34:2011

HAZARDOUS AREA CLASSIFICATION

ATEX CERTIFICATION No : SIRA 06ATEX1097X

ATEX CERTIFICATION CODE : II 2 GD Ex e II / Ex tD A21 IP66

IEC Ex CERTIFICATION No : IEC Ex SIR.06.0042X

IEC Ex CERTIFICATION CODE : Ex e II / Ex tD A21 IP66

INSTALLATION INSTRUCTIONS

Installation should only be performed by a competent person using the correct tools. Spanners should be used for tightening. Read all instructions

before beginning installation.

SPECIAL CONDITIONS FOR SAFE USE

1. The cable gland ranges shall only be used where temperatures at the point of entry is between -60°C and +130°C.

2. C2K cable glands are only suitable for fixed installations. Cables must be effectivelu clamped to prevent twisting and pulling

3. The entry component threads may need additional sealing to maintain the ingress protection rating as applicable to the associated equipment to

which it is attached

ACCESSORIES

The following accessories are available from CMP Products, as optional extras, to assist with fixing, sealing and earthing :-

Locknut | Earth Tag | Serrated Washer | Entry Thread (I.P.) Sealing Washer | Shroud *

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR INSTALLATION OF CMP CABLE GLAND TYPE C2K DUBAI • HOUSTON • NEWCASTLE • SINGAPORE • SHANGHAI • PUSAN • PERTH : : : : C2K IP66, IP67, IP68 BS EN ISO 9001 ISO/IEC 80079-34:2011 HAZARDOUS AREA CLASSIFICATION ATEX CERTIFICATION No : SIRA 06ATEX1097X ATEX CERTIFICATION CODE : II 2 GD Ex e II / Ex tD A21 IP66 IEC Ex CERTIFICATION No : IEC Ex SIR.06.
PAGE 2
www.cmp-products.com DUBAI • HOUSTON • NEWCASTLE • SINGAPORE • SHANGHAI • PUSAN • PERTH INSTALLATION INSTRUCTIONS FOR CMP CABLE GLAND TYPE C2K CABLE GLAND COMPONENTS 1. 2. 3. 4. 5. Entry Component Reversible Armour Cone AnyWay Clamping Ring Body Outer Seal Assembly Grooved Side (Braid) 1 2 Stepped Side (SWA) 3 4 4. Locate the Reversible Armour Cone (2) in the Entry Component (1). Stepped side outwards for SWA, grooved side outwards for all other cable types.