VER0220094800 HIGH DEFINITION DIGITALE SATELLITE-RECEIVER DVB 4800 Fig. 1.
General Imprint All rights reserved. Any reproduction without consent of cmx® is prohibited. cmx® reserves the right to modifications of the device.
General CONTEXTS 1. GENERAL ...................................................................................... - 4 1.1. Safety precautions ................................................................. - 4 1.2. Disposal of waste electronic equipment ................................ - 4 1.3. Battery disposal ..................................................................... - 4 1.4. Copyright ............................................................................... - 5 1.5.
General 1. General 1.1. Safety precautions Only connect to mains power supply (230 Volt/50 Hz). Do not place containers filled with water on top of the device. Do not place device in close proximity of water (e.g. sink, wash basin, etc.). The device can fall into the water and cause a short circuit. The device consumes some power during standby operation. For zero power consumption disconnect from mains power supply.
Features 1.4. Copyright It is illegal to copy, send, exhibit, broadcast via cable, publicly show or rent copyrighted materials without consent. 1.5. Hearing protection Select a moderate volume to protect your hearing. Only turn the volume to a level where you can still hear ambient noise. 1.6. Cleaning and maintenance Before cleaning disconnect from mains power supply. Do not clean with liquid cleaning agents or a wet cloth, this can cause a short circuit.
Location of controls 3. Location of controls 3.1. Main unit - front Fig. 3.
Location of controls 3.2. Main unit - rear Fig. 3.
Location of controls 3.3. Remote control Fig. 3.
Preparation 16 INFO Accessing program parameters 17 GREEN Function button GREEN 18 V-FMT Changing size of picture / function button RED 19 FAV Favourite lists indicate 20 ▼ Cursor button/ Normal mode: channel change 21 ◄ Cursor button, normal mode: decrease volume 22 OK Confirm the range 23 TEXT View teletext (switch transparent) 24 ▲ Cursor button, normal mode: channel change 25 MENU Menu button 26 RECALL Previous program 27 CH -/+ Previous program /next program 28 TV/
Preparation 4.1.1. Connection with SCART cable 1. Connect the SCART cable into the SCART jack “TV” on the receiver. 2. Connect the SCART cable with the TV. 3. To connect video devices connect a scart cable to the receiver’s “VCR” scart connector. To connect hi-fi systems connect the RCA cable to the receiver’s „AUDIO R“ and „AUDIO L“ connectors. 4.1.2. Connection with HDMI cable Fig. 4.1: Connection with scart cable 1. Connect the HDMI cable into the HDMI jack “HDMI” on the receiver. 2.
Preparation 4.1.3. Connection with component cable Connect a TV set with YUV connectors (YPbPr components) via a YUV component cable (YPbPr) to the receiver’s YPbPr component output. 1. Connect the component cables with the receiver. 2. Connect the component cable with the TV. 3. To connect video devices connect a scart cable to the receiver’s “VCR” scart connector. Fig. 4.
Start of operation and configuration Do not connect your hi-fi’s phono input to the receiver; this can damage your hi-fi-system. For radio reception you need not turn your TV set on. To receive the TV sound via your hi-fi system turn your TV set on. 1. Connect the coax cable to the receiver’s „COAXIAL“ connector. 2. Connect the coax cable to the digital audio amplifier. 3. Activate the receiver’s digital audio output in the menu item system settings TV system. 4.4.
Start of operation and configuration A list with all stored satellites is displayed. Press OK to activate or deactivate the desired satellite, a check mark is displayed. 4. Select menu item Antenna connector to set the LNB frequency and press EXIT to finish. 5. The submenus single / multi satellite allow setting the automatic channel search, press OK to confirm and start. 5.2. General operation For general navigation and control via remote control press ▲, ▼, ►, ◄.
Start of operation and configuration 5.3. Configuration Press MENU to display the main menu.
Start of operation and configuration HDD information HDD format PVR setting 5.3.1. Edit channel list Select the desired menu item and press OK to open the submenu. 5.3.1.1. TV program list FAV (Favorites) 1. Press FAV to select the favorites. The field „FAV“ is highlighted and activated. 2. Select the desired channel and press OK to confirm. Select the favorite list to insert the selected channel. The heart icon is displayed next to the selected channel. locking 1.
Start of operation and configuration Press EXIT to exit the menu. Moving 1. Press shortcut key YELLOW to select the channels. The field “Move” is highlighted and activated. You can move several channels simultaneously. 2. Select the channel and press OK to confirm. The move icon is displayed next to the selected channel. 3. Navigate the cursor to the position to insert the channels. 4. Press shortcut key YELLOW again to insert the channels in the current position. Press EXIT to exit the menu.
Start of operation and configuration 5.3.1.2. Radio channel list For editing the radio channel list same above functions as described for TV channels, are available. 5.3.1.3. Delete all Enter your valid password and confirm the security prompt to delete all saved TV and radio channels. Reset to default to restore the factory channel list. 5.3.2. Installation 5.3.2.1. Antenna connector Select your antenna type. 5.3.2.2. Satellite list Display all saved satellites. 1.
Start of operation and configuration Transponder List of programmed transponders DiSEqC 1.0 Set to multi satellite reception 22K Automatically setting Polarization Set polarization Motor Antenna LNB type Set LNB type Motor type Set motor type Local. Longitude Only motor type - USALS Delete all Delete satellite positions Not possible for motor type Motor settings Access DiSEqC 1.
Start of operation and configuration parameters. New Press shortcut key GREEN to add new transponder. Delete Press shortcut key YELLOW to delete transponder. Search Press shortcut key BLUE to scan transponder for new channels. 5.3.3. System setting Select the desired menu item and press OK to open the submenu. 5.3.3.1. Language Language Selection the language First audio channel Select audio language.
Start of operation and configuration 5.3.3.3. Local time setting GMT use Switch on and off GMT on GMT Difference: select local shift Summer time: on/off GMT off Adjust date Adjust time 5.3.3.4. Timer setting 8 timer settings are available to perform a service at a preset time, e.g. recording. Timer number Select timer 1 through 8 Timer mode Select between Off, Once, daily and weekly. Timer service VCR – at the preset time the receiver switches to the programmed event (also in standby mode).
Start of operation and configuration New password Enter a new password. Confirm password Repeat your new password. After confirming the new password it cannot be cancelled! 5.3.3.6. OSD setting OSD duration Select the duration of the OSD overlay. OSD transparency Select the transparency of the OSD overlay. 5.3.3.7. Favorite 8 favorite lists are available and can be renamed. 5.3.3.8. Other LNB power supply On/off. Preset is activating.
Start of operation and configuration Via USB Software update via USB port is preferred. Via satellite Necessary data are preset. Confirm the field “start” by pressing OK. Direct your satellite system to ASTRA1 19,2°east for software update. Software update does not save new TV channels, but only serves the software update of the receiver. Software update may take up to one hour. We recommend resetting to default settings before and after software update. The saved channel lists are deleted. 5.3.4.4.
Start of operation and configuration 5.3.5. Games There are 3 games available for entertainment. 5.3.6. External memory Connect a USB storage device to use this menu item. Programs that were recorded encrypted can be played back and decrypted after inserting the corresponding CI module and smart card. 5.3.6.1. Recording manager Here you can edit recorded programs. Rename Press the function button RED. Lock Press the function button GREEN. Delete Press the function button BLUE. 5.3.6.2.
Troubleshooting In case this menu item is deactivated only the image is frozen after pressing PAUSE. The time shift recording is not permanently saved on HDD: 2. Selecting a different channel or stopping the recording will cancel the time shift recording. The time shift function has a capacity of max 90 minutes. Skipping Select skipping steps in playback mode with the skip buttons. Minimum steps are 30 seconds, maximum steps are 30 minutes.
Warranty Remote control does not work Ensure the connectors. Check the function from the LNB. Decrease the distance to the system. Exchange the batteries. Point the remote control towards the system’s IR sensor. Image black & white Software crashed Select correct color standard. Disconnect from mains power supply and reconnect after a few seconds. 7. Warranty This system comes with a 24-month warranty from the date of purchase.
Warranty 7.1. Warranty procedure In case of malfunctions, please contact: Your dealer Service hotline o Austria: +43 0720 502671 – please dial with the zero! o Germany: +49 (0)180 166 66 264 621 o Switzerland: +41 (0) 848 00 3322 Contact form – www.cmx-electronics.com 7.2. Warranty has expired Please contact us by phone or contact form in case your warranty has expired. We will help you! Please inform us about the following: Unit type Purchase date malfunction 7.3.
Warranty Wrong Correct Unit is defect Unit does not respond. unit isn’t working Unit cannot be switched on Sender information: Name, address, ZIP code, city, phone number and e-mail address. Please cut out the warranty card.
Warranty - 28 -
Warranty - 29 -
Technical specifications 8. Technical specifications Receiver Frequencies 950 ~ 2150 MHz Video resolution 720 x 576 (Pal) / 720 x 480 (NTSC) / 1280 x 720 / 1920 x 1080 IF bandwidth 55 MHz / 8 MHz (under 5 MS/s) DiSEqc Version 1.0 / 1.2 Symbol rate 1 ~ 45 MS/s Error correction (FEC) 1/2, 2/3, ¾, 5/6, 7/8, auto Input speed Max. 15 Mbit/s LNB Power output 13/ 18V GS / 0,30 A-max.
Technical specifications Power consumption 25 Watt (Standby 2 Watt) Mains power AC 100-240 V ~ 50/60 Hz Temperature operation: 0°C ~ 40 °C storage: -40°C ~ 65°C Dimensions 310 x 50 x 200 mm - 31 -
Technical specifications www.cmx-electronics.
