Ver. 1.
Network Weatherproof Camera Installation Manual About this Installation Manual A compatibility and durability test ensured this product’s high performance. This installation manual is for XNET Network Weatherproof Camera users only, and it describes operations related to XNET Network Weatherproof Camera. Please read this manual thoroughly paying attention to cautions and warnings before using the product even if you have used similar products before.
Network Weatherproof Camera Installation Manual Index 1. About XNET ...................................................................................................................... 4 1.1. About XNET ............................................................................................................................. 4 1.2. XNET - Highlights ..................................................................................................................... 4 1.3. XNET Applications.............
Network Weatherproof Camera Installation Manual 1. About XNET 1.1. About XNET XNET is an internet based surveillance system that is compatible with various network conditions through easy installation, user interface, and multi-Codec such as MJPEG, MPEG-4, and H.264. XNET provides stable real-time surveillance by monitoring live mega pixel video and audio with local storage (in case of any network problems) and hybrid IP technology that can be integrated into the existing analog CCTV systems. 1.2.
Network Weatherproof Camera Installation Manual 2. About the Product 2.1 Contents Please make sure that no contents listed below are missing in the package. IBP5030CR PRODUCT SUNVISOR BRACKET SUPPORT BOLT AND SCREW L Wrench Power and Video Adaptor and Power Cable Terminal RJ45 SCREW CD 2.
Network Weatherproof Camera Installation Manual 2.3 Hardware 2.3.
Network Weatherproof Camera Installation Manual 2.3.2 Camera Module – Rear As shown in the picture above, open up the rear cap by undoing the four screws on the corners. Main body Rear body ① Illuminator Control Connector : controls the IR LED units ② Factory Reset Button : Press and hold for more than 3 seconds while power is on to recall factory default settings ③ Video Out Jack : Analog Video output. Use this output to monitor the analog video signal during installation.
Network Weatherproof Camera Installation Manual 2.3.3 Cable Connection z Power Input(#1, #2) Use the cable adapter in the package to connect power. Red –+12V DC, Black - GND Please use the accessory power supply provided in the package. (DC12V/5A) z Analog Video Output (#7, #8) Use this output for immediate monitoring of the video during installation. Use the supplied cable adapter (Yellow for video and White for Video GrounGGND) This adapter can be connected to a cable through a BNC termination.
Network Weatherproof Camera Installation Manual 2.3.4 Network Cable The waterproof cable from the product can be connected to a 10Mbps or 100Mbps Ethernet, and it uses a standard RJ-45 connector. Please follow the order listed below for network connection. 1. Cut the outer Jack of the 2. Insert Housing into Screw Ethernet cable as shown below. Nut (Recommended 3. Insert Seal into the Housing cable: 24AWG) 4. Insert the Ethernet cable from 5.
Network Weatherproof Camera Installation Manual 2.3.5 Adjusting Zoom and Focus As shown in the picture below, open up the front cap by undoing the four screws on the corners. Loosen the zoom and focus fix lever for adjustment, and tighten them back after. Focus Handle Use this lever to adjust the focus of the Lens Zoom Handle Use this lever to adjust the zoom magnification of the Lens When you are done with zoom/ focus adjustment, put the front cap back by tightening the four screws on the corner. 2.3.
Network Weatherproof Camera Installation Manual z Alarm Output This terminal can only be connected up to DC 30V/400mA. An additional relay switch is needed to control higher voltage or current. Internal Circuitry External Connection 2.3.7 Mounting the Camera 1. Install Sunvisor to the Camera’s MAIN BODY using Sunvisor blocks, washers, and screws. 2. Mount Bracket Support on a wall using four 6mm screws. 3.
Network Weatherproof Camera Installation Manual 3. Software Installation This section provides brief guidelines on installing the XNET software and using it to monitor Video and Audio. If you have questions about details not explained in this section or if the product is not functioning as described, please refer to FAQ before contacting your provider. Our homepage is http://www.cnbtec.com. 3.1. Connecting XNET to network 1. A PC or a laptop computer is required to configure an IP address.
Network Weatherproof Camera Installation Manual 3.2. Installing IP-Installer Software and Configuring IP address 3.2.1. About IP-Installer A unique IP address is required in order to connect the network camera to the network and have a Client PC connected to the camera remotely through the network. IP-Installer software, provided in the Installation CD and also available to download from http://www.cnbtec.com, makes it easy to configure the IP address.
Network Weatherproof Camera Installation Manual 2. Select the camera you wish to configure and click (Set IP Address) button to open the box shown in Figure 3-2. Figure 3-2. Set IP Address box 3. When you enter the IP address and click Set button, the box shown in Figure 3-3 will appear. Figure 3-3. Select Network Adapter Box 4. Select the adapter and click select button to change the IP address of the camera.
Network Weatherproof Camera Installation Manual 4. Using Web Viewer You can connect to the network camera using a web browser or “XNET-CMS” software. For instructions on how to use XNET-CMS software, please refer to XNET-CMS Manual, provided in the installation CD. 4.1. Logging In On your web browser, enter the IP address of the camera on the address bar and press enter key. Then the following box will appear: Figure 4-1.
Network Weatherproof Camera Installation Manual Enter the user name and password to bring up the web viewer page. The default id and password is “root” and “admin” respectively. If you changed the HTTP port number from the default value, put a colon and port number at the end of the IP address. (For example, enter http://192.168.123.100:8080 when using port 8080.
Network Weatherproof Camera Installation Manual 4.2. Web Viewer Page Web viewer page consists of Video area and menu area. Figure 4-2.
Network Weatherproof Camera Installation Manual Menu Sub Menu Capture - Setting - Description Captures and saves the current Video frame as a still image. The image is saved as jpeg file in the following folder: C:₩xNetCapture You can access the setup page for each XNET feature from this main setup page. Please refer to [XNET Owner’s Manual] for detail. This page can control digital PTZ of the camera, and it can also control the actual PTZ - PTZ movement.
Network Weatherproof Camera Installation Manual 5. Specifications IBP5030CR Camera System Progressive image processing Scanning System 4:3 Progressive Pixel Clock 48 MHZ Scanning Frequency (H) 26 KHz (NTSC) / 27 KHz (PAL) Scanning Frequency (V) 24 KHz (NTSC) / 25 KHz (PAL) Image Sensor 1/2" Progressive CMOS Sensor Sync. System Internal Effective Pixels Number 1280 (H) x 960 (V) 1.3 Mega pixel Horizontal Resolution 800 TV Lines Video Output Level Select NTSC/PAL 1.
Network Weatherproof Camera Installation Manual Web Viewer (Window Web Browser Base) Monitoring Application Live view for up to 10 user clients Video Snapshot to file (JPEG) XNET NVR, CNB CMS and Utility (IP-Installer, etc) Maintenance Mechanical System Upgrade Firmware upgrade over HTTP Digital Input / Output Control 1 Sensor / 1 Alarm, selectble with RS-485 by Cable PTZ control (RS-485) PTZ Protocol Service (User define update), selectable with Digital I/O by Cable Operating Temperature -10℃ ~
