XNET Network Dome Camera Install Guide XNET Network Dome Camera Install Guide ( IDP4030VR , IVP4030VR ) Ver. 1.
XNET Network Dome Camera Install Guide About this Manual A compatibility and durability test ensured this product’s high performance. This manual is for XNET Network Dome Camera users only, and it describes operations related to XNET Network Dome Camera. Please read this manual thoroughly paying attention to cautions and warnings before using the product even if you have used similar products before. Important Notices The copyright of this manual is owned by CNB Technology Inc.
XNET Network Dome Camera Install Guide Index 1. About XNET ....................................................................................................................................4 1.1. About XNET ............................................................................................................................4 1.2. Features of XNET....................................................................................................................4 1.3. Applications ..................
1. About XNET 1.1. About XNET XNET is an internet based security and surveillance system that is compatible with various network conditions through easy installation and user interface as well as multi-functional compressor Codec such as MJPEG, MPEG-4, and H.264. XNET provides stable real-time surveillance by real time video/ audio at SXGA level, local storage for any network problems, and hybrid IP technology that can be used with existing analog CCTV devices. 1.2.
2. About the Product 2.1. Contents Please make sure the following contents are included when you open the package. Contents XNET AC Power Cable Terminal CD Description Additional info. XNET Network Dome Camera 2Jack Cable Terminal for Alarm and Audio Software and User’s manual 2.2.
2.3. Hardware Designation 2.3.1. Switch and Controls This shows Camera module inside the dome cover. Alarm Input/Output Mic/Audio Input Audio Output FAN Analog Video Output Network Power Terminal Zoom Adjust Factory Reset button Recalls factory default configurations Focus Adjust CDS Sensor IR LED This CDS Sensor detects Low Light (night) and turns on IR LEDs.
2.3.2 Connecting Cables Power Supplies Power to the Xnet product. Use 12V DC Adapter in the package. Do not use this connector when powering up the product through LAN cable. (PoE) The product is not covered under warranty when it is damaged by connecting both Ethernet power and 12V DC power to this terminal. To 12VDC Power Adapter Analog Video Output Use this output to monitor the analog video signal while installing.
Network Terminal This Ethernet terminal connects to 100Mbps LAN through an RJ-45 connector. When optional PoE is used, the power will be supplied from the Network Cable. Link LED Yellow light indicates that the network is properly connected. Act LED Green light indicates that the XNET system connected to 100Mbps LAN. This green lamp will blink if the system receives data. 2.3.
3.Software Installation This section provides brief guidelines to install the XNET quickly and to monitor XNET’s Video and Audio signals easily. If you have questions about details not explained in this section or if the product is not functioning as described, please refer to FAQ before contacting the store. Our homepage is http://www.cnbtec.com. 3.1. Installing XNET 3.1.1. Installation Mount the Camera to a ceiling or a wall. Make sure the base is firm enough to hold the Camera.
Adjust the position, zoom, and focus as shown below: TILT : 90˚ FOCUS Horizontal ZOOM Rotation : 360˚ PAN : 360˚ 3. 3.1.2. Cable Connection 1.A PC or a laptop computer is required to set up an IP address. z Compatible operating system: Windows 2000/ Windows XP/ Windows Vista z Since the default IP address of the device is 192.168.123.100, set up the IP address of the computer like the following: IP Address : 192.168.123.101 Subnet Mask : 255.255.255.0 2.
3.2. Installing IP-Installer Software and Configuring IP address 3.2.1. About IP-Installer A unique IP address has to be configured in order to connect network camera and monitoring PC to a network. IP-Installer software provided in the Installation CD (included in the package and also available to download from our website http://www.cnbtec.com) will configure IP address easily. If your network have a DHCP server that automatically assigns IP addresses to network cameras.
B. Select the camera of which you wish to change the IP address and click (Set IP Address) button to bring up the following box in Figure 3-3. Figure 3-3. IP Address box C. When you enter the IP address and click Set button, the box shown in Figure 3-4 will appear. Figure 3-4. Select Network Adapter Box D. Select the adapter and click select button to change the IP address of the camera.
4.Using Web Viewer Connecting to network devices can be done using internet web browser or “XNET-CMS” software. This guide explains about using internet web browser only. For instructions on how to configure network connection using XNET-CMS software, please refer to XNET-CMS Manual, which can be found in the installation CD. 4.1. Logging In Enter the IP address of the device on the address bar of your web browser and press enter key.
4.2. Web Viewer Page Web viewer page consists of Video monitor screen and menu option buttons.
Item Sub Item Capture - Description Captures and saves the current image as a still picture. The image is saved as jpeg file in the following folder: C:₩xNetCapture Brings up Menu screen. Setting - Setup page for each XNET feature can be opened from this Menu screen. Please refer to [XNET Owner’s Manual] for detail. Opens up Motion Detection page. Motion - You can add or delete areas for detecting motion in this page. Please refer to [XNET Owner’s Manual] for detail. Opens up Multi View page.
System Back Light Compensation On/Off White Balance Auto/Manual Exposure Control Auto/Manual Day & Night Auto/Manual Functions B/W, Flickerless Electronic Shutter Speed NTSC : 1/6 ~ 1/600(13 Step), PAL : 1/6 ~ 1/500 (13 Step) Main Processors 32bit Embedded CPU with Linux System Memory NAND Flash Memory : 64MB, DDR Memory : 128MB Video/Audio SXGA / XGA : MJPEG Compression VGA : MJEPG / MPEG4 / H.