4600 CAN/PLIP INSTALLATION MANUAL
Summary 1.KIT CONTENTS.................................................................................................................................................3 2. INTRODUCTION & INSTALLATION METHODOLOGY (how to access to the vehicle specific technical documents, Data Linker tool, Antares software, how to define the installation solution) ......................................3 3.SYSTEM’S CONFIGURATION ..................................................................................................
1. - KIT CONTENTS. The following are the main parts supplied in the kit: - Main alarm unit. - Remote controls and/or Driver Card (if provided). - Wireless back-up battery siren or wired siren, loudspeaker. - Main unit universal wiring harness. - Siren wiring harness. - Siren bracket. - Ultrasonic sensors. - Installation accessories. - LED / control button. - Quick reference user manual. - Pin Code card. 2. - INTRODUCTION.
The list on the right side of the screen shows the product families. Clicking on the link you will get the full application list available for the destination vehicle for the product family selected. Check at first if there is a CAN application available, it offers the best compromise amoung functionalities offered/fitting time. If no one CAN product installation proposal is available, make the same research clicking on “PLIP alarm” range AK4600 – 4400 Plip.
4. - HOW TO PREPARE THE PIN CODE CARD. www.cobra-at.com Remove the separate PIN Code label from the back of the system main unit and place onto the supplied PIN Code Card. PLACE HERE THE PIN CODE LABEL 4C4415A2A S/N 0003 050524 PERSONAL IDENTIFICATION CODE PIN CODE 1122 5. - INSTALLATION PROCEDURE. System’s component positioning. As much as the components of the system will be placed in secure and difficult to access positions as higher the protection level will be.
Antennas. The RF antennas positioning (for both the main unit and the siren) is crucial for a proper system’s performance . They must not be cut, wrapped, connected to any other cables or to the vehicle body and they must be kept separate from the main wiring harness and as far as possible from metallic parts. Electrical connections. WARNING: Disconnect the negative lead from the battery before continuing with the installation. Pay attention when joining two or more wires.
J-22 Do not connect. J-23 Negative input for additional modules: to be used as a triggering input for the connection of compatible Cobra modules. J-24 Do not connect. J-25 CDL lock negative output: low power control signal to lock central door locking. Activated by the Cobra remote control , if provided (see electrical diagram F). J-26 analogic input: make the connection if required by the specific vehicle CAN installation sheet.
J-22 positive/negative perimetric input: to be connected to the vehicle roof lamp. The system configures automatically the input polarity 10 s after it has been armed. Make the functional test of the system after is has been configured. J-23 Negative input for additional modules: to be used as a triggering input for the connection of compatible Cobra modules. J-24 Do not connect. J-25 CDL lock negative output: low power control signal to lock central door locking.
46XX Art. (NO WIRELESS SIREN) See the vehicle fitting instructions or the CAN/PLIP J 26 connector pin out J1 GREEN J2 GREEN J17 WHITE J11 J16 J24 ORANGE-WHITE BROWN VIOLET-WHITE (NOT USED) J23 GREY J6 PINK-WHITE J20 PINK-BLACK J22 BLUE-PINK J19 ORANGE-BLACK J7 VIOLET-BLACK J26 YELLOW-BLACK J13 GREY-BLACK J18 GREEN-RED START +50 max 20A (1 sec.) 6A cont.
See the vehicle fitting instructions or the CAN/PLIP J 26 connector pin out Antenna 46XX Art. (WIRELESS SIREN) +30 15 A BLUE RED J14 BLACK +30 RED 3A CAN - L CAN - H VIOLET ORANGE ORANGE VIOLET J10 BLACK J15 J9 J21 BLUE J8 YELLOW-BLUE J1 GREEN J2 GREEN J17 WHITE J11 J16 J24 ORANGE-WHITE BROWN VIOLET-WHITE (NOT USED) J25 VIOLET J12 ORANGE J23 GREY See paragraph 11 COBRA BUS START +50 max 20A (1 sec.) 6A cont.
A B U.S. C U.S. WHITE wire J 17 D WHITE wire J17 -/+ +30 PA SS PA SS TX TX TX LE D TX LE D BLACK RX RX Y RX RX Y 87 RED ( TX) 30 86 85 -/+ Antenna Install the jumper wire (see the catalogue) between the Ultrasound TX and RX, if you don't use the volumetric sensor. +30 E WHITE wire J 17 WHITE (RX) BLACK - 3A U.S. sensors, led panel and antenna connections. Original relay controlled by a negative signal.
6.6 - Emergency panel LED. The LED main scope is to show the system arming and disarming conditions. When the system is armed the LED gets ON and remains illuminated until the 25 s arming period has elapsed. After that it starts blinking. It goes OFF as soon as the system is disarmed. 6.7 - Alarms memory.
7. - PROGRAMMABLE FUNCTIONS. To activate them refer to the “FUNCTIONS PROGRAMMING” table. 7.1 - Activation and volume adjustment of the audible arming and disarming signalling. This function allows to activate a short duration audible signal to confirm the system’s arming (1 beep) and disarming (2 beeps). 7.2 - Passive arming.
The driver recognition must happen any time the ignition key is turned to the ON position or when, with the ignition key already ON, the driver side door is opened and then closed to get off the vehicle. If the driver is not recognized within 60 s the emergency panel LED starts flashing quickly signalling for the next 30 s the missed driver recognition.
8 - HOW TO PROGRAM FUNCTIONALITIES, COBRA REMOTE CONTROLS AND DRIVER CARDS SELF LEARNING PROCEDURE. IMPORTANT: (only for PLIP applications and just after the power supply connection or when the battery has been disconnected and reconnected). Before entering in the functions programming procedure, arm the system, wait until the emergency panel LED starts flashing, then disarm the system. From now on it will be possible to performe the programming procedure. PROCEDURE: a. Open the driver side door. b.
9.- FUNCTIONAL TEST. During the first 25 s after the system has been armed all protection functionalities can be tested without triggering an alarm. Make the following tests during the 28 s inhibition time with the system armed: open then close one by one all doors and boot - Check if the system is confirming with three audible signal, each door opening detection.
A. B. C. D. E. F. G. Power the main unit by connecting the 26 ways connector. Connect the main unit blue wire to GND (only when a wireless siren is fitted). Open the bonnet. Connect the siren blue wire to GND (if not already grounded through the additional bonnet pushbutton). Disconnect the siren 6 ways connector, then plug it again. Within 60 s turn the ignition key ON, an audible signal confirms that the siren has been stored in the system.
14. - FOR UK MARKET ONLY Category 1,2 or 2-1 systems permanently installed as aftermarket equipment by import or distribution centres, vehicle dealers, or by Independent Installers, shall be installed by companies and technicians who are trained, qualified, industry recognised professional installers.
Cobra Automotive Technologies via Astico 41 - 21100 VARESE - ITALY www.cobra-at.com 06DE3325B - 10/11 2.
