MODELS: LS600V- LS6000 COBRA LOG SPLITTER OWNER’S MANUAL
Cobra LS600V - Log Splitter Description 1 2 3 4 5 6 Splitting blade Control arm-left Splitting table Motor On / Off-switch 8 9 Wheel Locking bolt 2 10 11 12 13 14 15 16 17 18 Control arm-right Control handle Clamping claw left Retaining pin Handle Stroke adjustment rod Holding screw Splitting cross Hydraulic valve 20 21 22 23 24 25 Safety label 1 Safety labelcap 2 with dip stick Oil tank Safety label 3 Safety label 4 Clamping claw right Star grip screw
Cobra LS600V - Log Splitter Assembley STEP 1: Mount control arms Insert control arms and insert pipe in recess of cross con-nection. STEP2: Tip: grease the metal plates at top and bottom first! STEP3: Push the holding bolt through. STEP 4 Lock the holding bolt at the bottom.
Cobra LS600V - Log Splitter Assembley Mounting the log rest: Depending on the length of the wood to be cleaved, the table can be mounted at three different heights. Locking bolts are available in every installation position. Fit the table into the appropriate mounting angles. Pay attention that the locking bolt is engaged.
Do not operate machine before having read the operating instructions, understood all the notes and assembly the machine as described here. Nobody else should be in the working area of the machine other than the operator. Keep other persons or animals out of the danger area (minimum distance 5 m). Keep the instructions in a safe place for future use. Wear hearing protection when working with the machine to protect your hearing.
User information. This information helps you to use all the functions optimally. Assembly, operation and servicing. Here you are explained exactly what to do. Proper use The log splitter must only be used for splitting logs. Only straight-cut logs are suitable for use with the log splitter. Foreign bodies (nails, wire, concrete etc.) must always be removed from the wood before it is split.
Switch the machine off and remove the mains plug from the socket when carrying out repair works maintenance and cleaning work checking connecting lines, whether these are knotted or damaged removing faults transporting leaving unattended (even during short interruptions) Check the machine for possible damage Before continuing to use the machine, the protective devices must be inspected to ensure that they work perfectly and with their intended function Check whether the movable parts fun
Venting Vent the hydraulic system before putting the log splitter into operation. ! Unscrew venting screw by several turns so that air may escape from the oil tank. ! Leave the screw open during operation. ! Close the venting screw before moving the log splitter, as otherwise oil will leak at this point. L Lock in case of power (zero-voltage initiator) The equipment will switch off automatically if there is a power cut. Repress the green button to switch it on again.
Operation Two-hand operation Never operate the log splitter with two people. Never block the control handles (clamping claws). 1. Press the green switch on the electric motor. Wait a few moments until the motor has reached its operating revolutions and the required pressure has been built up in the hydraulic pump. L At temperatures below –5° C, let the log splitter run for at least 15 min. in neutral to heat up the oil. 2. Place the log on the log splitter table.
1. Release the locking bolt. Splitting long wood: 1. Middle or low position of table or base. 2. Remove the splitting cross. 3. Place the log on the splitter’s table. L 2. Pull the table out. Possible malfunction when cleaving logs: The log to be cleaved is not cleaved right through, jams on the cleaving blade and is pulled up during the blade’s return movement. In this case, proceed as follows: 1. Switch off the device. 2.
Finishing work: ¾ Bring the splitting blade to the lower position (run-in state). ¾ Release one of the control handles. ¾ Switch the machine off and disconnect the power. ¾ Follow the care and maintenance instructions. Care and maintenance Remove the plug from the power socket before starting any maintenance or cleaning work. dip stick Wear protective gloves in order to avoid injury to the hands.
L Hydraulic oil We recommend the following hydraulic oils for the hydraulic cylinder: ¾ ¾ ¾ ¾ ¾ Shell Tellus T 22 Aral Vitam Gf 22 BP Energol HLP 22 Mobil DTE 11 or equivalent Do not use any other types of oil. The use of any other type of oil will adversely affect the operation of the hydraulic cylinder. drain plug Guarantee This product is warranted in accordance with legal regulations for a 24 month period effective from the date of purchase by the first user.
Technical data LS600V - LS6000 6N Type Model Splitting force Log length Log diameter Stroke 60 kN (6 t) max. 1050 mm min. 120 mm – max. 300 mm | 500 mm Hydraulic oil (max.) Hydraulic pressure Electric motor performance (power consumption) Power supply 4.5 litres 20 MPa (200 bar) P1 3.0 kW S6 (4 min/6 min) 230 V~ 50 Hz, 13 A time-lag Weight approx. 100 kg Possible problems Problem Possible cause Remedy Logs are not being split The log is not positioned correctly. Reposition the log correctly.
. EC-DECLARATION OF CONFORMITY EC Declaration of Conformity We herewith declare, Cobra Garden Machinery Henton & Chattell Ltd, London Road, Nottingham NG2 3HW UK That the following machine complies with the appropriate basic safety and health requirements of the EC Directive based on its design and type, as brought into circulation by us.
