65hm1735801aproductspecs

ManualsBrandsCocyan ManualsMisc. Servo Motors6.5" MagX servo hub motor

Table Of Contents

MagX

Product Specification

产品规格书

Customer code

客户代码

深圳普渡科技有限公司

Model No

产品型号

轮毂电机 HM17358-01A

Revision No

版次

A00

Date

日期

20210910

1. This specification applies to HM17358-01A motor to be supplied to you.

本规格书为您所提供的只适用于：HM17358-01A 电机。

2. If the motor performance or life is questionable，tests and judgment are to be made based on

this specification.

您对电机的性能和寿命有疑问，可根据本规格书来测试和判断。

3. Please read this specification carefully to ensure that the motor can satisfy the requirements

of your application.

请仔细阅读此规格书，以确保这款电机能满足您的要求。

4. After you receive this specification, please give us feedback within one month. If you do

not reply, we shall consider that you have acknowledged this specification.

在您收到此款规格书后，请一个月之内反馈给我们。如果您未回复，我们视您已承认

了此款规格书。

ACKNOWLEDGMENT

（客户承认书）

*Please sign and return immediately.Thank you

（请签章回传）

TOPBAND CO.,LTD.ELECTRIC MOTOR DIV.

Prepared by

编制

Checked by

审核

Approved by

批准

Summary of content (9 pages)

PAGE 1
MagX Product Specification 产品规格书 Customer code 客户代码深圳普渡科技有限公司 Model 轮毂电机 HM17358-01A No 产品型号 Revision No 版次 A00 Date 日期 20210910 1. This specification applies to HM17358-01A motor to be supplied to you. 本规格书为您所提供的只适用于：HM17358-01A 电机。 2. If the motor performance or life is questionable，tests and judgment are to be made based on this specification. 您对电机的性能和寿命有疑问，可根据本规格书来测试和判断。 3. Please read this specification carefully to ensure that the motor can satisfy the requirements of your application.
PAGE 2
1Construction-form 结构形式 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 Motor construction Hub Motor 电机结构轮毂电机 Number of phases 3phases 相数 3-相 Number of magnet poles 38-Poles 磁极极数 38-极(磁钢内置) Coil construction Concentrated winding 线圈结构集中绕组 Rectifying method Electronic Rectifying 换向方式电子换向 Silicon steel sheets material B35A400 硅钢片牌号 B35A400 magnet material 磁铁 N45M 100°c N45M 100 摄氏度 shaft material 40Cr 轴材料 40Cr Coil QZY-2 Φ0.95 180°c QZY-2 Φ0.
PAGE 3
、Measuring conditions 测试条件 3-1 3-2 3-3 Motor Position 出力轴水平放置电机姿势 Power Supply 可调节直流稳压电源，确保测量时无疑问电源 Environmental Temperature and Humidity 温度和湿度 The test is made in principle of a temperature between+10℃ to+30℃，And at relative humidity between 30% and 95%. 原则上温度为 10℃-30℃，湿度为 30-95%。 4、Electrical Characteristics 电气性能 4-1 4-2 No-load speed 空载转速 No-load current 空载电流 200rpm±8% At Rated voltage and No-load 额定电压及无负载下测试 0.5 A max At Rated voltage and No-load 额定电压及无负载下测试 4-3 Rated load 额定负荷 6N.
PAGE 4
Reference 4-10 curve 性能曲线 4
PAGE 5
、External & Functional Characteristics . 结构及机械性能 5-1 External appearance 外观 Outer dimensions to be within the tolerances specified in the attached Drawing page 9 remarkable deformation or superficial defects to be observed by visual check. Fastened parts to be fixed firmly 外形尺寸符合附图 P9 外观应无明显变形或表面损伤，紧固件应安装牢固。 5-2 Shaft end play 轴向间隙轴向间隙 5-3 Weights 重量 5-4 Mechanical Noise 机械噪音 0.05-0.20 mm Approx 3.
PAGE 6
、Environmental Tests:环境试验 6-1 Vibration Test 振动试验 6-2 Drop Test 跌落试验 6-3 6-4 6-5 6-6 The motor difference in comparison with initial performance should keep within ±10% after motors subjected to the sine wave of 2 mm amplitude and frequency sweep 16.7HZ in the X.Y.Z directions for 2 hours each 电机在 X、Y、Z 三个方向经过振幅为 2mm，频率为 16.7HZ 的正弦波扫描振动各 2 小时后，其性能参照 4.1~4.8 允许±10%变化。.
PAGE 7
、Life test 寿命试验 7-1 Start stop test Environment: 25℃±5℃/65%±20%RH 持续运行环境条件： 25℃±5℃/65%±20%RH Voltage: 24V DC constant 电压： 24V 直流恒定电压 Load: Pulley.load equivalent to 6N.m 负载：负载 6N.m 10000 hours min 最少 10000 小时 Before/After life test, measuring the rated load specification. Motor life is judged to come to an end , when one of the following occurs: 寿命试验前后测定电机的额定负载特性,出现下列情况之一时,判为寿命终止: 1) Rated-load speed gets varied over±30% against the initial figure. 额定负载转速超过初始值的±30%.
PAGE 8
、Precautions in using the motor 马达使用注意事项：（1）When mounting your motors by means of binding agents, DON’T allow any adherence to the bearings nor intrusion into the motors. 使用粘合剂安装电机时，不充许有任何异物附着到轴承或电机内。（2）Axial thrust on the output shaft could have an adverse effect on the motor life .i.e. As is produced by worm gears, fans, etc.
PAGE 9