User Manual
Table Of Contents
- 1GENERAL
- 1.1Introduction
- 1.2Interim Operation
- 1.3Manual Organization
- 1.4UT-4R400 Transmitter Family Models
- 1.5Performance Specifications
- 1.5.1General
- 1.5.2Audio Specifications
- 1.5.3Physical Specifications
- 2THEORY OF OPERATION
- 2.1General
- 2.2Power Supply
- 2.3High Speed Serial Interconnect
- 2.4Audio Circuits
- 2.5PTT Circuitry
- 2.6Microprocessor Board
- 2.7Channel and Bank Selection
- 2.7.1Channel Select Line Mapping
- 2.8Jumper Functions and standard configuration
- 2.9Hang Timer Selection
- 2.10Kerchunk noise selection
- 2.11Test Points
- 2.12Connector Pinouts
- 2.12.1Connector J9
- 2.12.2Connector P1
- 2.13Transmitter Programming
- 2.13.1Transmitter Wide Options
- 2.13.1.1Frequency Band
- 2.13.1.2Source ID
- 2.13.1.3Secure Hardware Equipped
- 2.13.1.4Timeout Options
- 2.13.2Channel Wide Settings
- 2.13.2.1Channel Name
- 2.13.2.2Frequency
- 2.13.2.3Analog Bandwidth
- 2.13.2.4Deviation
- 2.13.2.5Channel Type
- 2.13.2.6Audio Pre-emphasis
- 2.13.2.7Timeout Value
- 2.13.2.8Project 25 Squelch Settings: Network Access Code (NAC)
- 2.13.2.9Project 25 Squelch Settings: Talk Group ID (TGID)
- 2.13.2.10Analog Signaling Settings: Signaling
- 2.13.2.11Analog Signaling Settings: CTCSS Tone
- 2.13.2.12Analog Signaling Settings: Reverse Burst
- 2.13.2.13Analog Signaling Settings: DCS Code
- 2.13.2.14Analog Signaling Settings: Turnoff Code
- 2.13.2.15Analog Squelch Settings: Invert DCS
- 3Transmitter Assembly and Adjustment
- 3.1Frequency Change
- 3.2Minor Frequency Change
- 3.3Major Frequency Change
- 3.4Digital Signal Processor Board Alignment
- 3.4.1Radio Service Software
- 3.4.2Radio Programming Interface Module Interconnection
- 3.4.3Reference Oscillator Adjustment
- 3.4.4Transmitter Deviation Balance Adjustment
- 3.4.5Transmitter Deviation Limit Adjustment
- 3.4.6Audio Level Alignment
- 3.4.7Amplifier Alignment
- 3.5Recommended Test Equipment List
- 3.6Repair Note
- 3.7Printed Circuit board Numbering Convention
- 4Repeater System Configuration
- 4.1Interim Repeater
- 4.1.1Repeater Interconnect Cable Pinout
- 4.2Project 25 Compliant Repeater
- 4.3Repeater System Troubleshooting
- 5ILLUSTRATIONS
- 5.1Digital Repeater Transmitter Front Panel
- 5.2Digital Repeater Transmitter Exploded View
- 5.3Digital Repeater Transmitter Block Diagram (Interim Mode)
- 5.4Digital Repeater Transmitter Schematic Diagram
- 5.5Digital Repeater Transmitter Main Board Component Layout (Bottom)
- 5.6Digital Repeater Transmitter Main Board Component Layout (Top)
- 5.7Digital Repeater Microprocessor Board Component Layout (Bottom)
- 5.8Digital Repeater Microprocessor Board Component Layout (Top)
- 6PARTS LIST
- 6.1Digital Repeater Transmitter Main Board Parts List
- 6.1.1Digital Repeater Transmitter Main Board Electrical Parts List
- 6.1.2Digital Repeater Transmitter Main Board Mechanical Parts List
- 6.2Digital Repeater Microprocessor Board Parts List
- 6.2.1Digital Repeater Microprocessor Board Electrical Parts List
- 6.2.2Digital Transmitter Additional PCBs
- 7REVISION HISTORY
Instructions
1. Remove the four screws (B) on the side of the Transmitter Case.
2. Remove the four Front Panel screws (A).
3. Remove the Transmitter Case.
4. To remove the TX Power Amplifier, remove the two Front Panel screws (F).
and the 4 screws (D) holding the TX Power Amplifier to the TX Main PCB.
5. To remove Digital Controller PCB shield, remove the five screws (C).
6. To remove Digital Microprocessor PCB, remove 1 screw(H) and 2 standoffs.
and disconnect the 2 ribbon cables between the 2 PCBs.
7. To remove Digital Controller PCB, remove 3 screws (G) and 3 standoffs.
8. To remove Digital RF PCB shield, unsolder 4 pins.
9. To remove Digital RF PCB, remove two screws (E) and 2 slotted standoffs.
10. Assembly is the reverse of steps 1 through 8.
A
A
A
A
TRANSMITTER
14 HP CASE
B
B
B
B
TRANSCEIVER RF
BOARD SHIELD
(4 Pins Soldered to main PCB)
TX POWER AMPLIFIER
D
D
D
D
E
E
DIGITAL SIGNAL
PROCESSOR PCB
TRANSMITTER FRONT PANEL
DIGITAL TRANSMITTER
TRANSCEIVER RF PCB
Slide PCB into slot 4
DIGITAL TRANSMITTER
MAIN PCB
F
F
G
G
DIGITAL TRANSMITTER
MICROPROCESSOR PCB
C
C
C
C
C
DIGITAL SIGNAL
PROCESSOR
BOARD SHIELD
G
H
Project 25 Digital Transmitter Instruction Manual
5.2 Digital Repeater Transmitter Exploded View
DE
DANIELS
ELECTRONICS
xT4DM2B
5-2