User Manual
MT-4E VHF & UHF Receiver & Transmitter Instruction Manual
IM08-MT-4E-TXRX Project 1106
iii
RF Exposure Warning
Exposure to radio frequency (RF) energy has been identied as a potential environmental factor that must be
considered before a radio transmitter can be authorized or licensed. The FCC and IC have therefore developed
maximum permissible exposure (MPE) limits for eld strength and power density, listed in FCC 47 CFR 1.1310
and IC RSS-102 Issue 2 Sect 4. The FCC has furthermore determined that determination of compliance with
these exposure limits, and preparation of an Environmental Assessment (EA) if the limits are exceeded, is
necessary only for facilities, operations and transmitters that fall into certain risk categories, listed in FCC 47
CFR 1.1307 (b), Table 1. All other facilities, operations and transmitters are categorically excluded from making
such studies or preparing an EA, except as indicated in FCC 47 CFR 1.1307 (c) and (d).
Revised FCC OET Bulletin 65 (Edition 97-01) and IC RSS-102 Issue 2 provide assistance in determining
whether a proposed or existing transmitting facility, operation or device complies with RF exposure limits. In
accordance with OET Bulletin 65, FCC 47 CFR 1.1307 (b) and RSS-102 Issue Sect 2.5, this Daniels Electronics
Ltd. transmitter is categorically excluded from routine evaluation or preparing an EA for RF emissions and this
exclusion is sufcient basis for assuming compliance with FCC/IC MPE limits. This exclusion is subject to the
limits specied in FCC 47 CFR 1.1307 (b), 1.1310 and IC RSS-102 Issue 2 Sect 4. Daniels Electronics Ltd. has
no reason to believe that this excluded transmitter encompasses exceptional characteristics that could cause
non-compliance.
Notes:
• The FCC and IC’s exposure guidelines constitute exposure limits, not emission limits. They are relevant
to locations that are accessible to workers or members of the public. Such access can be restricted or
controlled by appropriate means (i.e., fences, warning signs, etc.).
• The FCC and IC’s limits apply cumulatively to all sources of RF emissions affecting a given site. Sites
exceeding these limits are subject to an EA and must provide test reports indicating compliance.
RF Safety Guidelines and Information
Base and Repeater radio transmitters are designed to generate and radiate RF energy by means of an external
antenna, typically mounted at a signicant height above ground to provide adequate signal coverage. To
reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication.
The following antenna installation guidelines are extracted from Appendix A from OET Bulletin 65 and must be
adhered to in order to ensure RF exposure compliance:
Non-building-mounted Antennas:
Height above ground level to lowest point of antenna ≥ 10 m or
Power ≤ 1000 W ERP (1640 W EIRP)
Building-mounted Antennas:
Power ≤ 1000 W ERP (1640 W EIRP)
The following RF Safety Guidelines should be observed when working in or around transmitter sites:
• Do not work on or around any transmitting antenna while RF power is applied.
• Before working on an antenna, disable the appropriate transmitter and ensure a “DO NOT USE” or
similar sign is placed on or near the PTT or key-up control.
• Assume all antennas are active unless specically indicated otherwise.
• Never operate a transmitter with the cover removed.
• Ensure all personnel entering a transmitter site have electromagnetic energy awareness training.
For more information on RF energy exposure and compliance, please refer to the following:
1. FCC Code of Regulations; 47 CFR 1.1307 and 1.1310.
2. FCC OET Bulletin 65, Edition 97-01, “Evaluating Compliance with FCC Guidelines for
Human Exposure to Radiofrequency Electromagnetic Fields.”
3. http://www.fcc.gov/oet/rfsafety/.
4. IC RSS-102 Issue 2, “Radio Frequency Exposure Compliance of Radio Communication Apparatus.”