User Manual
Table Of Contents
- 1GENERAL
- 1.1Introduction
- 1.2Manual Organization
- 1.3VT-4B 136 - 174 MHz Transmitter Family Models
- 1.4Performance Specifications
- 1.4.1General
- 1.4.2Audio Specifications
- 1.4.3Physical Specifications
- 2THEORY OF OPERATION
- 2.1Transmitter Operation
- 2.2Transmitter Programming
- 2.2.1Transmitter Wide Options
- 2.2.1.1Disable Front Panel Led
- 2.2.1.2Secure Hardware Equipped
- 2.2.1.3Allow Emergency Transmissions
- 2.2.1.4Allow Radio Inhibit
- 2.2.1.5Allow Radio Check
- 2.2.1.6Enable Status
- 2.2.1.7Frequency Band
- 2.2.2Channel Wide Settings
- 2.2.2.1Frequency
- 2.2.2.2Voice/Signal Type
- 2.2.2.3Squelch Type
- 2.2.2.4CTCSS Tone
- 2.2.2.5Enable Reverse Burst
- 2.2.2.6DCS Code
- 2.2.2.7DCS Invert
- 2.2.2.8Enable Turn Off Code
- 2.2.2.9Transmitter Power
- 2.2.2.10Channel Bandwidth
- 2.2.2.11Deviation
- 2.2.2.12Time Out Timer
- 2.2.2.13Channel Status
- 2.2.2.14Transmitter Pre-emphasis
- 2.2.2.15NAC Transmitter Code
- 2.2.2.16NAC Transmitter
- 2.3Transmitter Programming using Motorola Radio Service Software
- 2.4Secure Communications
- 2.5Transmitter Assembly and Adjustment
- 2.5.1Controller Board Alignment
- 2.5.1.1Reference Oscillator Adjustment
- 2.5.1.2Transmitter Deviation Balance Adjustment
- 2.5.1.3Transmitter Deviation Limit Adjustment
- 2.5.2Amplifier Alignment
- 2.5.3Frequency Change
- 2.6Recommended Test Equipment List
- 2.7Repair Note
- 2.8Printed Circuitboard Numbering Convention
- 3ILLUSTRATIONS
- 3.1MT-4 Base Transmitter Front Panel
- 3.2MT-4 Transmitter Case - Exploded View
- 3.3Digital Base Transmitter Block Diagram
- 3.4Digital Base Transmitter Schematic Diagram
- 3.5Digital Base Transmitter Main Board Component Layout (Bottom)
- 3.6Digital Base Transmitter Main Board Component Layout (Top)
- 4PARTS LIST
- 4.1P25 Base Transmitter Main Board Parts List
- 4.1.1P25 Base Transmitter Main Board Electrical Parts List
- 4.1.2P25 Base Transmitter Mechanical Parts List
- 5REVISION HISTORY
DE
DANIELS
ELECTRONICS
VT-4B150 VHF Project 25
Digital
Base
Transmitter
Instruction
Manual
2-7
by the frequency counter matches the test frequency displayed on the screen to within +/- 150 Hz.
Click on the "UPDATE SOFTPOT" button to save the setting in the transmitter's non-volatile
memory. This completes the adjustment of the reference oscillator. Leave the RF Board
disconnected from the amplifier module and continue with the next alignment procedure.
2.5.1.2
Transmitter Deviation Balance Adjustment
This adjustment equalizes the modulation sensitivity of the low and high frequency modulation
paths on the RF board. To perform the adjustment, disconnect the RF Board from the amplifier
module by separating the SMB connectors. Connect the RF output cable of the RF board to a
communications test set. Connect the transmitter to an IBM compatible computer using the
Programming Cable. Apply power to the transmitter and run the Radio Programming Software.
Navigate to the TRANSMITTER \ SERVICE TRANSMITTER \ DEVIATION BALANCE screen,
where you will see a list of test frequencies and current SoftPot values for each frequency.
YSelect the radio button next to the first test frequency and click on the "LOW PTT" button. This
causes an internally generated 80 Hz tone to be applied to the modulator. Note the deviation of the
carrier on the communications test set, and click on the "HIGH PTT" button. This causes a 3 kHz
tone to be applied to the modulator. Adjust the slider next to the test frequency until the measured
deviation matches that of the 80 Hz tone. Now click on the "LOW PTT" button again to check the
deviation. If the deviation has changed from the original reading, note the new deviation and
perform the adjustment at the high frequency again. It may require several iterations of this
process to get the deviations to match within +/- 2%. When the deviations match, click on the
"UPDATE SOFTPOT" button to save the setting in the transmitter's non-volatile memory.
YRepeat the adjustment process for each of the test frequencies. Leave the RF Board disconnected
from the amplifier module and continue with the next alignment procedure.
2.5.1.3
Transmitter Deviation Limit Adjustment
This adjustment prevents over-deviation of the transmitter's carrier. To perform the adjustment,
disconnect the RF Board from the amplifier module by separating the SMB connectors. Connect
the RF output cable of the RF board to a communications test set. Connect the transmitter to an
IBM compatible computer using the Programming Cable. Apply power to the transmitter and run
the Radio Programming Software. Navigate to the TRANSMITTER \ SERVICE
TRANSMITTER \ ADJUST DEVIATION LIMITS menu item, where you will see a list of test
frequencies and current SoftPot values for each frequency. Select the radio button next to the first
test frequency and click on the "ENABLE TX" button to key the transmitter. Adjust the slider next
to the selected test frequency under the measured deviation of the carrier is between 2785 Hz and
2885 Hz. Click on the "UPDATE SOFTPOT" button to save the new setting to the radio's non-
volatile memory. Repeat the process for each test frequency. This completes the adjustment
process for the transmitter deviation limits, and completes the alignment process for the Main
Board.