User Manual
Table Of Contents
- 1GENERAL
- 1.1Introduction
- 1.2Interim Operation
- 1.3Manual Organization
- 1.4VT-4R400 Transmitter Family Models
- 1.5Performance Specifications
- 1.5.1General
- 1.5.2Audio Specifications
- 1.5.3Physical Specifications
- 2THEORY OF OPERATION
- 2.1General
- 2.2Power Supply
- 2.3High Speed Serial Interconnect
- 2.4Audio Circuits
- 2.5PTT Circuitry
- 2.6Microprocessor Board
- 2.7Channel and Bank Selection
- 2.7.1Channel Select Line Mapping
- 2.8Jumper Functions and standard configuration
- 2.9Hang Timer Selection
- 2.10Kerchunk noise selection
- 2.11Test Points
- 2.12Connector Pinouts
- 2.12.1Connector J9
- 2.12.2Connector P1
- 2.13Transmitter Programming
- 2.13.1Transmitter Wide Options
- 2.13.1.1Frequency Band
- 2.13.1.2Source ID
- 2.13.1.3Secure Hardware Equipped
- 2.13.1.4Timeout Options
- 2.13.2Channel Wide Settings
- 2.13.2.1Channel Name
- 2.13.2.2Frequency
- 2.13.2.3Analog Bandwidth
- 2.13.2.4Deviation
- 2.13.2.5Channel Type
- 2.13.2.6Audio Pre-emphasis
- 2.13.2.7Timeout Value
- 2.13.2.8Project 25 Squelch Settings: Network Access Code (NAC)
- 2.13.2.9Project 25 Squelch Settings: Talk Group ID (TGID)
- 2.13.2.10Analog Signaling Settings: Signaling
- 2.13.2.11Analog Signaling Settings: CTCSS Tone
- 2.13.2.12Analog Signaling Settings: Reverse Burst
- 2.13.2.13Analog Signaling Settings: DCS Code
- 2.13.2.14Analog Signaling Settings: Turnoff Code
- 2.13.2.15Analog Squelch Settings: Invert DCS
- 3Transmitter Assembly and Adjustment
- 3.1Frequency Change
- 3.2Minor Frequency Change
- 3.3Major Frequency Change
- 3.4Digital Signal Processor Board Alignment
- 3.4.1Radio Service Software
- 3.4.2Radio Programming Interface Module Interconnection
- 3.4.3Reference Oscillator Adjustment
- 3.4.4Transmitter Deviation Balance Adjustment
- 3.4.5Transmitter Deviation Limit Adjustment
- 3.4.6Audio Level Alignment
- 3.4.7Amplifier Alignment
- 3.5Recommended Test Equipment List
- 3.6Repair Note
- 3.7Printed Circuit board Numbering Convention
- 4Repeater System Configuration
- 4.1Interim Repeater
- 4.1.1Repeater Interconnect Cable Pinout
- 4.2Project 25 Compliant Repeater
- 4.3Repeater System Troubleshooting
- 5ILLUSTRATIONS
- 5.1Digital Repeater Transmitter Front Panel
- 5.2Digital Repeater Transmitter Exploded View
- 5.3Digital Repeater Transmitter Block Diagram (Interim Mode)
- 5.4Digital Repeater Transmitter Schematic Diagram
- 5.5Digital Repeater Transmitter Main Board Component Layout (Bottom)
- 5.6Digital Repeater Transmitter Main Board Component Layout (Top)
- 5.7Digital Repeater Microprocessor Board Component Layout (Bottom)
- 5.8Digital Repeater Microprocessor Board Component Layout (Top)
- 6PARTS LIST
- 6.1Digital Repeater Transmitter Main Board Parts List
- 6.1.1Digital Repeater Transmitter Main Board Electrical Parts List
- 6.1.2Digital Repeater Transmitter Main Board Mechanical Parts List
- 6.2Digital Repeater Microprocessor Board Parts List
- 6.2.1Digital Repeater Microprocessor Board Electrical Parts List
- 6.2.2Digital Transmitter Additional PCBs
- 7REVISION HISTORY
VT-4R150 VHF Project 25
Digital
Transmitter
Instruction
Manual
v
6 PARTS LIST.................................................................................. 6-1
6.1
Digital
Repeater
Transmitter
Main
Board Parts List................................. 6-1
6.1.1
Digital
Repeater
Transmitter
Main
Board
Electrical
Parts List.................. 6-1
6.1.2
Digital
Repeater
Transmitter
Main
Board
Mechanical
Parts List................ 6-4
6.2
Digital
Repeater
Microprocessor
Board Parts List .................................. 6-5
6.2.1
Digital
Repeater
Microprocesso
r Board
Electrical
Parts List.................... 6-5
6.2.2
Digital
Transmitter
Additional
PCBs............................................... 6-6
7
REVISION HISTORY
....................................................................... 7-1
MODULE
MANUALS
VHF
Amplifier
Instruction
Manual
VT-3 132 - 174 MHz...............
IM21-VT3150AMP