Remote Vehicle Control System CA 650 Owner's Manual Vehicle Security and Remote Start System with Two Way Confirming LCD Remote Control IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
Table of Contents Using Your Remote Control .......................................................... 3 Arming the security system Passive Arming Hidden alarm function Disarming the security system Two stage door unlock* Automatic rearm Valet mode Using Your Remote Control, continued ....................................
Using Your Remote Control Arming the Security System To arm the system, exit the vehicle, close all doors, then press the LOCK icon button on the remote control. The system will sound once and the parking lights will flash once, indicating the system is armed. The doors will also lock at this time (if equipped and connected). The status indicator (red warning light on the dash) will blink steadily, once per second. To arm the system silently, press the LOCK and UNLOCK icon buttons for 1 second.
Using Your Remote Control, continued Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the TRUNK icon button on the remote control for 2 seconds will open the vehicle’s trunk or hatch. Activating Optional AUX 1 (Optional) If this feature is enabled on your system, pressing the LOCK and TRUNK icon buttons on the remote control simultaneously will activate an optional feature.
Using Your Remote Vehicle Starter Remote Starting Your Vehicle To activate the remote vehicle start function, press and release the STAR button on the remote control two (2) times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds.
Using Your Remote Vehicle Starter, continued Operating the 2 / 3 Hour Start Up Timer Mode The system has the ability to start the vehicle every 2 or 3 hours with a MAXIMUM of 6 start cycles. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. WARNING! Be certain that the vehicle is outdoors before using this or any remote starting device.
Additional 2-Way LCD Remote Control Functions Check Vehicle Status Press and release the TRUNK button and then simultaniously press the LOCK and UNLOCK buttons, the transmitter will respond with one melody sound and display the current status of the vehicle. LCD Remote Control Display Illumination Press and release the TRUNK button on the LCD remote control one time. The display will illuminate for 5 seconds.
LCD Remote Control ICON’s ARM IGN LOCK UNLOCK SYSTEM ARMED VALET MODE TRANSMITTING IN-RANGE INDICATOR HOOD/TRUNK TRIGGER DOOR TRIGGER WARN AWAY TRIGGER FULL SHOCK TRIGGER IGNITION ON/TRIGGER ENGINE RUNNING TIME CONTROL START 2 CAR MODE BATTERY INDICATOR PAGE FROM VEHICLE SAVE BATTERY SAVE MODE VIBRATE/SILENT MODE 8
LED and Siren/Horn Indications LED Display Indications LED Function OFF DISARMED SLOW FLASH ARMED FAST FLASH PASSIVE ARMING ON (SOLID) VALET MODE 2 FLASH... PAUSE ZONE 2 TRIGGER, HOOD/TRUNK 3 FLASH... PAUSE ZONE 3 TRIGGER, DOOR 4 FLASH... PAUSE ZONE 4 TRIGGER, SHOCK 5 FLASH...
Replacing Remote Control Batteries 2-way LCD Remote Control: The AAA alkaline battery inside the 2-way LCD remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the BATTERY icon on the LCD remote control will show. 1. 2. 3. 4. 5. Slide the small release tab on the back of the remote control to the unlock position.
Emergency Override Procedure If your transmitter is lost or disabled, it will be necessary use the emergency override button to turn the security system off. There are two types of emergency override procedures. Check with your installing dealer to find out what has been activated on your system. Standard Emergency Override Procedure 1. Enter the vehicle, the security system will trigger. 2. Turn the ignition key to the ON position. 3. Press and release the emergency override button.
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc.
FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.