User's Manual

ManualsBrandsCode Alarm ManualsAutomobile AlarmCode Alarm Code Alarm Automobile Alarm CSI-200

128-

1 of 8

3 Button Remote Security System with

Stage Shock Sensor & Starter Disable

Model CSI-200

Owner’s Manual

FEATURES :

 2 Four Button Code Hopping RF Transmitters

 Four Channel Code Learning Receiver (capable of accepting 4 transmitters)

 Selectable Manual Override Mode

 Remote Panic in all modes

 Protected Valet

 7 Function LED -(Light Emitting Diode) - Arm / Disarm / Zone1, 2, 3 / Valet / Arming

 Intrusion Alert with Memory

 Audible Arm / Disarm / Defective Zone / Tamper Confirmation

 Instant Siren Activation

 Low Current Horn Output

 Starter Disable

 True Last Door Arming (hardwire only)

 Defective Zone By - Pass

 Hardwire or Voltage Sense Selectable

 Active or Passive Arming Selectable

 Programmable Auto Lock On / Off

 Programmable Auto Unlock, Drivers Door All Doors On / Off

 Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L

 Programmable Active or Passive Door Locks

 User Programmable Permanent Chirp Delete

 On Command RF Chirp Delete from Transmitter (Software Selectable)

 6 Tone Multi - Tone Siren

 Additional Negative Trigger Input

 RF Inhibit with ignition on

 Parking Light Flasher

 Plug In Dual Stage Shock Sensor

OPTIONS :

 Remote Trunk Release

 Remote Keyless Entry

 Illuminated Entry

 Multiple Vehicle Capable

 Remote Starter

 Remote Power Window Roll Up

 Remote Garage Door Interface

 Two Step Unlock Configurable

Summary of content (8 pages)

PAGE 1
Model CSI-200 Owner’s Manual 3 Button Remote Security System with Stage Shock Sensor & Starter Disable FEATURES : 2 Four Button Code Hopping RF Transmitters Four Channel Code Learning Receiver (capable of accepting 4 transmitters) Selectable Manual Override Mode Remote Panic in all modes Protected Valet 7 Function LED -(Light Emitting Diode) - Arm / Disarm / Zone1, 2, 3 / Valet / Arming Intrusion Alert with Memory Audible Arm / Disarm / Defective Zone / Tamper Confirmation Instant Siren Ac
PAGE 2
NOTE: Your system has the option of using a siren, the vehicle horn, or both for the sounding device. Where the siren is referenced below, the horn or both may in fact chirp, or beep. ARMING THE SYSTEM - ACTIVE 1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid. 2. Press and release the ARM button on the keychain transmitter. ; The dash mounted LED begins to flash slowly. ; Parking Lights flash two times. ; Siren and or Horn sounds two chirps.
PAGE 3
PROTECTION WHILE THE SYSTEM IS ARMED ; Opening any protected door, hood, or trunk lid will cause the alarm to immediately sound. The alarm will continue to sound for 30 seconds, then stop and continue to monitor all protected entry points. If the thief left a door opened, the alarm will sound for six 30 second cycles, remain armed and ignore that triggered zone. ; Whenever the system is armed, the dash mounted LED indicator will slowly flash. This serves as a visual deterrent to the potential thief.
PAGE 4
button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. 1. As you approach the vehicle, press and hold the unlock button on the keychain transmitter for 2 seconds. ; The dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is re arming automatically. Open any door to suspend the automatic arming. ; Parking Lights flash one time.
PAGE 5
valet mode, all alarm functions are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed either by using your keychain transmitter, or by operating the manual override sequence. 1. From the disarmed condition, turn the ignition key to the on position. 2. Press and hold the valet push-button switch until the dash mounted LED, turns on. The LED will remain on as long as the system is in valet mode. 3.
PAGE 6
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. Custom Code Programming Example: To Change the code from the factory preassigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3.
PAGE 7
1. Turn the ignition key on then off. 2. Within 10 seconds, press and release the valet push button switch three times. 3. If the chirps were on before you started, then you will hear 2 chirps indicating they have been turned off. If the chirps were off before you started, then you will hear one chirp indicating they have been turned on. NOTE: Whenever the chirps are by - passed, the 4 chirp intrusion indicator and 4 chirp defective zone indicator will always operate.
PAGE 8
CSI-200 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING SLOW FLASHING OFF ON SOLID 3 FLASH...PAUSE 2 FLASH...PAUSE 1 FLASH...PAUSE = = = = = = = PASSIVE ARMING ARMED DISARMED VALET MODE INTRUSION ZONE 3 INTRUSION ZONE 2 INTRUSION ZONE 1 = = = = DISARM ARM ARM / DOOR OPENED DISARM / INTRUSION SIREN CHIRP INDICATORS 1 CHIRP * 2 CHIRPS * 4 CHIRPS 4 CHIRPS * These chirps are optional, and can be de-activated.