PROFESSIONAL SERIES CA 1551 Owner’s Guide Deluxe Vehicle Security and Keyless Entry System with 2 Way Confirming LCD Remote Control IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. 2010 Audiovox Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control ............................................................... 3 Arming the Security System ............................................................ 3 Passive Arming Bypass ................................................................... 3 Bypassing the Shock Sensor .......................................................... 3 Hidden Alarm Function ...................................................................... 3 Disarming the Security System ......
Using Your Remote Control Arming the Security System To arm the system, exit the vehicle, close all doors, then press the button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second.
Two Stage Door Unlock (Optional) If this feature is enabled on your system, pressing the button one time will unlock only the driver’s door. Press again within three seconds to unlock the remaining doors. Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the seconds will open the vehicle’s trunk or hatch.
Eliminating Arm / Disarm Notification Chirps System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks. 1. Turn the ignition ON then OFF. 2. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF. Manually Overriding the Security System Your system can be disarmed without the use of the transmitter.
LED and Siren/Horn Indications LED Display Indications LED Function OFF DISARMED SLOW FLASH ARMED FAST FLASH PASSIVE ARMING ON (SOLID) VALET MODE 2 FLASH... PAUSE ZONE 2 TRIGGER, HOOD/TRUNK 3 FLASH... PAUSE ZONE 3 TRIGGER, DOOR 4 FLASH... PAUSE ZONE 4 TRIGGER, SHOCK 5 FLASH...
Additional 2-Way LCD Remote Control Functions Check Vehicle Status Press and release 2 times then press within 3 seconds, the transmitter will respond with one melody sound and display the current status of the vehicle. Display Illumination Press and hold the seconds. button for 1 second.
Button Lock Press and release then press hold the for 2 seconds to toggle the button lock on or off. When the button lock is active, the remote control will beep/vibrate 2 times when a button is pressed indicating it is locked. Illumination Press and release 2 times then press and hold for 2 seconds to toggle illumination on or off. When on, the display will illuminate when it receives or sends a command.
LCD Remote Control ICON’s LOCK UNLOCK SYSTEM ARMED VALET MODE TRANSMITTING IGNITION ON/TRIGGER TRUNK TRIGGER DOOR TRIGGER HOOD TRIGGER FULL SHOCK TRIGGER SYSTEM TRIGGER TIME COUNT DOWN BATTERY INDICATOR BATTERY SAVE MODE VIBRATE/SILENT MODE MELODY MODE 2 CAR MODE TIME DISPLAY ALARM CLOCK AUX 1 OUTPUT 2010 Audiovox Electronics Corporation. All rights reserved.
Transmitter Button Functions 1 Way Transmitter Lock Lock Unlock Car Find / Panic Operation Method X Press and Release Unlock X Press and Release 2 Step Unlock X Press and Release 2 times Trunk X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) AUX 1 X Shock Bypass X X Press and Release Lock then Press Lock + Car Find Hidden Alarm X X Press and Release Car Fnd then Press Lock X X Press and Release Unlock Car Find / Panic Passive Arming B
Replacing Remote Control Batteries 1 Way 4 Button Remote Control The batteries (model CR2016) inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries: 1. Remove 3 screws and disassemble the halves of the remote control. 2.
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc.
2010 Audiovox Electronics Corporation. All rights reserved.
Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.