User Manual Code Reader™ 2600 Manual Version 04 Release Date: February 2013 C007964_04_CR2600_User_Manual C007964_04_CR2600_UserManual
Statement of Agency Compliance The Code Reader™ 2600 (CR2600) has been tested for compliance with FCC regulations and was found to be compliant with all applicable FCC Rules and Regulations. IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, this device must not be co-located or operate in conjunction with any other antenna or transmitter.
Code Reader™ 2600 User Manual Copyright © 2013 Code Corporation. All Rights Reserved. The software described in this manual may only be used in accordance with the terms of its license agreement. No part of this publication may be reproduced in any form or by any means without written permission from Code Corporation. This includes electronic or mechanical means such as photocopying or recording in information storage and retrieval systems. NO WARRANTY. This technical documentation is provided AS-IS.
Table of Contents 1.0 - Unpacking............................................................................................................................................................... 1 2.0 - Charging Station Assembly Instructions................................................................................................................... 1 3.0 - Battery Installation and Removal.....................................................................................................................
1.0 - Unpacking Remove the CR2600 from its packing and inspect it for damage. If the reader was damaged during shipping, please call Code at (801) 495-2200. Based on the kit purchased, a combination of the following components will be included with the CR2600: Charging Station with Embedded CodeXML® Modem Weighted Base Plate Screws Charging Station CodeXML® M3 Modem with USB or RS232 cable USB Cable Battery Power Supply Rubber Feet 2.0 - Charging Station Assembly Instructions 1.
3.0 - Battery Installation and Removal Place the battery into the reader as shown below. Once in place, the battery will snap and lock to indicate proper installation. For battery removal, slide the latch (Figure 8), to unlock and release the battery. Latch Figure 7 Figure 8 4.0 - Charging the CR2600 1. Plug the USB cable into the computer’s USB port (Figure 9) or the power adapter into the wall outlet (Figure 10).
5.0 - Fuel Gauge Battery Status Indicators Check the Battery Life Press the fuel gauge button(Figure 13) to determine remaining battery life. If the battery has less then 10% capacity, the first LED will flash rapidly. For 25% or greater capacity, the LEDs will flash ON for 4 seconds.
.0 - Communication Mode Switch Charging Stations with an embedded modem feature a Communication Modem Switch. The Communication Mode Switch allows the reader to transmit data through either the modem or wired connection. When the Communication Mode Switch is moved to the right, in the direction of the arrow, the reader will communicate via the modem. The QuickConnect code located on the front of the Charging Station must be scanned to establish a Bluetooth connection.
2. Scan the preferred Batch Mode configuration bar code: Batch Mode Enable - Send and Log Batch Mode Enable - Log Only 3. Scan the preferred Communication Mode settings: USB Keyboard Mode USB Downloader Mode USB Virtual Comm Mode 4. To transmit the captured data to CortexTools™ on your host device, place reader into charging station. The reader will wait 5 seconds before transmitting data. The 5 second delay allows the host device to prepare to receive the data. 11.
13.0 - Establishing a Bluetooth® Connection 1. If establishing a Bluetooth connection using the Charging Station with embedded CodeXML® Modem, slide the Communication Mode Switch on the Charger/Modem Station (Figure 19), to Bluetooth mode (the direction of the arrow). 2. Scan the QuickConnect Code located on the front of the Charging Station with embedded CodeXML® modem or on the external CodeXML® M3 Modem (Figures 20 and 21). 3.
15.
19.0 - Reader ID and Firmware Version To find out the Reader ID and firmware version, open a text editor program (i.e., Notepad, Microsoft Word, etc.
20.0 - CR2600 Dimensions CR2611 CR2612 20.
21.0 - CR2600 Maintenance The CR2600 needs only minimum maintenance to operate. The tips below for maintenance suggestions. Cleaning the CR2600 The CR2600 window should be clean to allow the best performance of the device. The window is the clear plastic piece inside the head of the reader. Avoid touching the window. Your CR2600 uses CMOS technology that is much like a digital camera. A dirty window may stop the CR2600 from reading bar codes.
22.0 - Warranty Code’s CR2600 carries a standard three year limited warranty as described herein. Charging Stations follow the warranty of the reader. The CR2600 battery carries a one year limited warranty. Customers may purchase either a one or two year CodeOne extended warranty plan. Please contact a Code representative for more information. Limited Warranty Code manufactures its hardware products in accordance with industry-standard practices.