Operating instructions
Pag. 2 http://www.coef.it - info@coef.it
This equipment is destined to an exclusively Professional use.
READ ALL CAUTIONS AND WARNINGS PRIOR TO OPERATE THIS EQUIPMENT.Instruction to prevent injury or damage
due to electric shock, fire, mechanical hazards and UV radiation hazards.
• PROTECTION AGAINTS FIRE
1) This equipment is designed for use with the following lamps only: MSD 1200W MSR 1800W.
DO NOT USE ANY OTHER TYPE LAMP!
2) Maintain minimum distance of 0.5 meter from walls or any other type flammable surfaces.
3) Maintain minimum distance to lighted objects of 5.0 meter.
4) Replace fuses only with the specified type and rating.
5) Do not install the spot close to heat sources. Do not lay the connection cable on the spot when it is warm.
• PROTECTION AGAINST ELECTRIC SHOCK
1) This equipment must be earthed.
2) Class I equipment. The power supply cord includes a protective earthing conductor as part of the cord.
3) For connection to the supply mains proceed as pict.1 page 3. The equipment must be connected to branch circuit having a
circuit- breacker (Code 02B012 In=16A Id=0.03A 230VAC) (Code 02B013 In=32A Id=0.03A 230VAC).
4) Disconnect power before lamp’s replacement or servicing (service personnel).
• PROTECTION AGAINST MECHANICAL HAZARDS
1) Use secondary safety chain when fixing this equipment.
2) Hot lamp explosion hazard. Do not open the equipment for 300 seconds after switching off.
3) Equipment surface may reach temperature up to 100°C. Allow about five minutes before handling.
4) Replace the lamp if it is damaged or thermally deformed.
• PROTECTION AGAINST UV RADIATION HAZARDS
1) Do not start on this equipment without lamp enclosure or if the protection screens, or ultraviolets screens are damaged.
2) The protection screens, the lenses, or the ultraviolet filters must be replaced if they are visibly damaged and their effective
-
ness has been reduced, for example, by cracks or deep scratches.
3) Do not look directly at the lamp while lamp is on.
ATTENTION: carefully read the directions of this manual. Exclusively follow the safety rules in force and do not carry
out assembly and/or maintenance operations without taking all precautions as indicated in the different sections or
without the necessary specialization.
This manual must always accompany the equipment, therefore it must be available and readable at any moment if
necessary. Also in case of sale, rent, change of place and/or ownership, these documents shall be enclosed with the
relative equipment.
INTRODUCTION
Thank you for using the Sirio 1800DV/2500DV !
The Sirio 1800DV/2500DV projects, thanks to an extremely efficient optic system (international patent n. WO99/40361), a
powerful light beam which can create numberless color shades. Its performances, in terms of luminousity and lighted surfaces, can
reach incredible levels.
The Sirio 1800DV/2500DV comes in two versions:
• Cod. 02B012 Sirio 1800DV for MHD 1200W discharge lamp
• Cod. 02B013 Sirio 2500DV for MHD 2500W discharge lamp or HMD 2500W discharge lamp
The Sirio 1800DV/2500DV can work in automatic mode or in synchro mode, otherwise may be controlled by 8 bit DMX control
-
lers. The input protocol is the DMX 512. To drive the Sirio 1800DV/2500DV we suggest to use our controller MasterShow 512.
To make the most of its possibilites and for a correct functioning of this unit in the years to come, we suggest you to read
carefully this manual before connecting or putting the spot into use. By doing so you will gain experience with its commands and
connections and you will be easily able to use it.
ADVICES FOR A CORRECT INSTALLATION
Declaration of CE conformity
COEF srl. Via Albinatico, 80-82 / 51019 Ponte Buggianese (Pistoia) ITALY
Declare that the product
Sirio 1800/2500DV is in conformity with 89/336 EEC-EMC directive and
with the actual required safety standars in accordance with LVD 73/23 EEC