FILTERBREW & SERVING CONCEPT TECHNICAL MANUAL TM_EN Part No.
CONTENT FILTERBREW & SERVING CONCEPT CONTENT......................................................................................................................................................... 2 GENERAL............................................................................................................................................................ 4 Introduction....................................................................................................................................
CONTENT FILTERBREW & SERVING CONCEPT EXPLODED VIEW....................................................................................................................................... 36 A-2............................................................................................................................................................................. 36 M-2..........................................................................................................................................
GENERAL FILTERBREW & SERVING CONCEPT Introduction Thank you for choosing a FILTERBREWER coffee machine. We hope you enjoy it ! Read the user guide before using the machine. This guide contains important instructions for proper and safe use of the vending machine. Always keep this guide close at hand for future reference. Warnings Never immerse the machine, plug or mains cable in water because there is a danger of electric shock.
CLEANING AND CARE FILTERBREW & SERVING CONCEPT Rinse Thermos, Decanter and Serving station Before each brewing, rinse the thermos, decanter or serving station with fresh tap water. When cleaning the outside, use a soft rag with liquid cleaning agent to prevent scratches. CAUTION! The machine should not be submerged in water or washed in a dishwasher. it will result in machine damage.
CLEANING AND CARE FILTERBREW & SERVING CONCEPT Dayly cleaning Wash the thermos, decanter(B) and the filter holder with liquid solution for coffee machines. Always remove the filter immediately and clean the filter holder daily, coffee will get moldy. Clean the spray nozzle(A) and the surrounding area. Use a soft rag and liquid solution that does not scratch. A B B Pitcher PT No.110351 Weekly cleaning Descaling and cleaning.
CLEANING AND CARE FILTERBREW & SERVING CONCEPT Cleaning Serving station A Disassemble the level tube and clean it every week with the enclosed brush. Take off the main lid and clean the mixer tube(A). Cleaning of Serving station IMPORTANT! Rinse the inside of the serving station several times with fresh tap water. Fill the serving station with hot water. ( Full brewing without coffee and filter ). Put 1 tablespoon with cleaning powder in the serving station and wait at least 15 minutes.
PROGRAMMING FILTERBREW & SERVING CONCEPT A-2, DA-4, Thermos A, Mega Gold A Select machine type Enter the procedure to select machine type is the following: Press all three buttons , and at the same time before turning on the mains switch The buzzer beeps once. The display shows the current setting. Step up with button Press the button MACHINE TYPE 8 and step down with button . to save setting and exit to normal mode. DISPLAY CUPS CUPS TIME BUZZER TIME DA/A-2 T1 4-12 9.
PROGRAMMING FILTERBREW & SERVING CONCEPT A-2, DA-4, Thermos A, Mega Gold A Adjust water amount Adjust amount of brew water Press the buttons and at same time in 5 seconds. The buzzer beeps twice. Display shows 0. - Press the button to increase amount of water. - Press the button to decrease amount of water. - 1 step = 5% - Press the button to confirm the change.
PROGRAMMING FILTERBREW & SERVING CONCEPT Cater Normal operation with reduced outlet time This mode is entered by pressing the and before turning the mains switch on. The buzzer gives a 5s beep to indicate this mode. This machine operates like in normal mode but the outlet times are reduced by 90% in order to allow faster adjustment of valve times. Adjusting of water temperature Press buttons and at the same time for 5 seconds until you hear one beep.
PROGRAMMING FILTERBREW & SERVING CONCEPT Cater Adjusting of water quantity ADJUST DISPLAY 25% 5 20% 4 15% 3 10% 2 5% 1 0% 0 -5% -1 -10% -2 -15% -3 -20% -4 -25% -5 The procedure to enter this mode is the following: Press buttons and at the same time for 5 seconds until you hear 3 beeps. The display shows the current setting. Adjust with the buttons Presse the = (increase) and = (decrease). button to save new settings and return to normal mode.
PROGRAMMING FILTERBREW & SERVING CONCEPT Cater Select machine type In this mode the machine type can be chosen. The procedure to enter this mode is the following: Press buttons , and at the same time before turning the mains switch on until you hear 6 beeps. The display shows the machine type. Step up with button Presse the and step down with button . button to save new setting and return to normal mode. Outlet time (s) Full Half Machine type Display Buzzer time (s) 1.
PROGRAMMING FILTERBREW & SERVING CONCEPT Cater Test functions Press buttons and at the same time before turning the mains switch on, puts the control board into test mode for time and temperature controlled machines. For the other types pressing buttons in test mode.
PROGRAMMING FILTERBREW & SERVING CONCEPT Tower Normal operation with reduced outlet time This mode is entered by pressing and before turning the mains switch on. The buzzer gives a 5s beep to indicate this mode. This machine operates like in normal mode but the outlet times are reduced by 90% in order to allow faster adjustment of valve times.
PROGRAMMING FILTERBREW & SERVING CONCEPT Tower Adjusting water temperature A Press left buttons and at the same time for 5 seconds until you hear1 beep. Display shows the present setting(A). Adjust with the left buttons (increase water temp.) and (decrease water temp.) Confirm the new settings by pressing the left 70°0C = min. temperature. 96°0C = max. temperature. button once.
PROGRAMMING FILTERBREW & SERVING CONCEPT HVA/HVM Select machine type Use a decanter to fill up the water tank to the long sensor pin.(A) Keep button (B) pressed while turning on the power switch.(D) A A D E B C The display will show T1, change the type of machine with buttons (B) or (C). T1 = HVA automatic T2 = HVM manual Confirm the choice by holding down the buttons (B) and (C) at the same time for approximately 5 seconds.
PROGRAMMING FILTERBREW & SERVING CONCEPT Grinder Original Normal operation There are several sub modes for this mode: A READY The machine is in this mode after power on. The motor is off and timers are stopped. Pressing the button and changes the number of cups to be prepared.The number of cups is displayed on the 2 digit display. The range is 4 -34 cups.The latest number of cups will be used even after power cycling the machine.
PROGRAMMING FILTERBREW & SERVING CONCEPT Grinder Original Adjust coffee amount Press buttons A and simultaneously for 6 seconds. The display (A) shows the current time setting for grinding. You can now choose to increase or decrease the time 15 = 1.5 seconds for or grinding, by pressing the buttons . This means that you increase or decrease the amount of coffee grounds. Adjust coffee grind A The grinding degree is preset from the factory.
POSSIBLE SOLUTION FILTERBREW & SERVING CONCEPT Original A/M Fault and solution FAULT IMPORTANT! All maintenance and installations must be done of an authorized technician. POSSIBLE SOLUTION Power switch does not lit heck plug connection to wall socket. C Check fuse in plug. Check if hot plate becomes warm, if so replace power switch. Hot plate does not become warm although switch is lit. Check connection to hot plate. If hot plate is defective, replace. Brewer excess steam.
POSSIBLE SOLUTION FILTERBREW & SERVING CONCEPT Cater, Tower, HVA/HVM Fault and solution LEVEL CONTROL Remove the power cord from the wall socket during any installation work. SHOWN ON THE DISPLAY POSSIBLE FAULT - The high water level sensor is triggerd before the low level sensor. IMPORTANT! All maintenance and installations must be done of an authorized technician. POSSIBLE SOLUTION - Clean the level sensor. - Replace. - Cables connected is incorrectly. - The machine fills slowly.
Rocket Switch Double Heating Plate A2 A2 Black IN2 UT4 IN5 UT3 IN6 7 6 14 4 PCB Original A UT1 Black Black Blue Black Blue Blue Yellow/Green A1 Black A1 Blue AUT ELH MIC 1 MIC 2 Micro Switch Blue Brew Element MAN ELH Heating Plate Black Black Black Blue Inlet Valve 1.
IN2 6 IN5 Brew Lamp Black Black IND Black 15 13 11 Rocket Switch Double UT4 OPL IND Blue Blue Blue Rocket Switch Double Black Blue Blue Black AUT M2 Heating Plate M2 ELH 230 Main Socket 230 MAN ELH Black Black 230 Yellow/Green Brew Element MIC 1 MIC 2 Miscro Switch Black Heating Plate M2 M2 ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT M-2
Black MIC1 Microswitch 2 MIC2 Temperture Controller 2 AUT Black ELT Blue A1 4 6 14 7 MAIN PCB 2 Blue Black Over Heating Protector 2 MAIN Heating Plate 3 Blue A2 Blue A1 Heating Element 2 ELT Black AUT Black Yellow/Green Black IN6 Black UT4 Blue UT3 Blue IN6 Heating Plate 4 A2 Black Rocket Switch Double 2 Black IN2 Yellow/Green IN5 VENT VENT VENT Double inlet valve VENT IN2 IN5 UT4 UT3 IN6 Black IN6 Rocket Switch Double 1 Black Black Connector FV Blac
Black AUT INT Black AUT Temperture Controller 2 MIC1 Microswitch 2 MIC2 Black INT ELT ELT M2 M2 Blue Blue Heating Element 2 Black Heating Plate 4 MAIN MAIN Over Heating Protector 2 Black Blue Heating Plate 3 M2 M2 Blue Blue 6 11 Rocket Switch Double 2 13 UT4 Black 15 230 230 230 230 Yellow/Green Connector FV Rocket Switch Double 1 15 13 6 UT4 OPL 11 Blue Blue Blue M2 M2 MAIN MAIN Over Heating Protector 1 Black Heating Plate 2 Blue Blue ELT ELT I
Black Black A-1 3 2 1 6 5 4 Blue PCB Original A Rocket Switch Green/Yellow Black Black Blue A-1 Black MIC 1 MAN ELH MIC 2 Black Blue Black Brew Element Micro Switch AUT ELH Blue 230 VENT Inlet Valve 1.
UT 5 Brew Lamp IND Rocket Switch Black IND IN 4 UT 2 IN 1 Black Black Blue Blue Black 19 Blue M1 Blue AUT Main Socket 230 Black 230 ELH Brew Element 230 MAN ELH MIC 1 Micro Switch Black MIC 2 ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT Mega Gold M, Termos M, Office
3 2 Rocket Switch 6 5 4 Blue Blue Inlet Green Yellow Brew Lamp Blue Blue Black Black PCB Black Black Tank GND Element NTC Red Black Level Sensor Black Black Black Black High Limit Switch Black Solid State Note: - Thick wire ≥ 100V - Thin wire ≤ 24V Blue Black Green Yellow Black Blue Main Socket Black 1 Blue Black ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT Single Cater 27
ELECTRICAL SCHEMATICS Cater 28 FILTERBREW & SERVING CONCEPT
ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT T L3 S L2 L1 N High limit switch 220V 220V ZERO GND 3 Fuse 5 6 2 Switch 4 1 220V R Relay Outlet-1 Outlet-2 PCB Tank GND Tower 3x400VAC+Zero+Ground 29
3 GND 5 6 2 Switch 4 1 High limit switch Fuse T L3 S L2 220V 220V R L1 Relay Outlet-1 Outlet-2 Inlet PCB EL-1 R-S NTC Solid state-1 Tank GND EL-3 S-T Solid state-2 EL-2 T-R Solid state-3 ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT Tower 3x230VAC+Ground 220V
L1 L2 R S 3 230V Zero N Transformer 400-500VAC GND 5 6 2 Switch 4 1 High limit switch Fuse T L3 S L2 400-500V 400-500V R L1 Relay Outlet-1 Outlet-2 Inlet PCB EL-1 R-S NTC Solid state-1 Tank GND EL-3 S-T Solid state-2 EL-2 T-R Solid state-3 ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT Tower 3x400-500VAC+Ground 400-500V 31
ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT Grinder Original Note: - Thick wire ≥ 100V - Thin wire ≤ 24V 32
ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT V-2 Chassis GND Heating Plate 1 Chassis GND Heating Plate 2 Brown Brown White ROCKET SWITCH 1 4 2 5 3 6 White 1 Black Black Blue Blue 4 2 5 3 6 ROCKET SWITCH Chassis GND 230V Input Main Power Socket 33
Inlet valve Inlet Inlet Rocket Switch 5 6 2 3 Main socket 4 1 Blue Blue 230 Chassis GND Black Black Yellow/Green Yellow/Green 230 230 PCB 7 Black 6 Black 14 4 1 3 10 2 9 8 Black Tank Short Blue Black Sol4 Black Red Black Sol1 Tank Long 4 1 Black Sol3 Sol2 EL Black Solid state 3 2 ELE ELE Blue NTC High limint Switch OH OH ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT HVA/HVM 1-Phase
ELECTRICAL SCHEMATICS FILTERBREW & SERVING CONCEPT HVA/HVM 3-Phase Blue Red Black Black Blue Red Black Note: - Thick wire ≥ 100V (Black, Blue wire) - Thin wire ≤ 24V 35
EXPLODED VIEW FILTERBREW & SERVING CONCEPT A-2 Drawing 2 3 6 Tank Float Strainer Cover Microswitch holder 21 20 4 8 22 7 9 5 23 25 13 1 14 12 15 11 10 29 28 24 26 16 36 19 17 18 27
EXPLODED VIEW FILTERBREW & SERVING CONCEPT A-2 Spare parts list POS. Amount/Unit Part No. Description 1 2 120811 (230V) Warming plate 230V/95W 1 2 1208121 (110V) Warming plate 110V/95W 2 1 1204012 Lid of tank original 3 1 1204013 Strainer original 4 1 160821 (230V) Micro switch tank 1.8L 4 1 1608221 (110V) Micro switch 125V 5 1 1204016 Spray nozzle for water tank 6 1 1204015 Water tank complete 1.8L 7 1 1505041 Hot water hose 1.8L 8 1 1561036 Drainage hose 1.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT M-2 Drawing 2 Tank Float Strainer Cover Microswitch holder 3 6 21 20 7 8 22 4 5 9 10 1 23 12 13 11 19 17 16 14 15 38 18
EXPLODED VIEW FILTERBREW & SERVING CONCEPT M-2 Spare parts list POS. Amount/Unit Part No. Description 1 2 120811 (230V) Warming plate 230V/95W 1 2 1208121 (110V) Warming plate 110V/95W 2 1 1204012 Lid of tank original 3 1 1204013 Strainer original 4 1 1505041 Silicon hose hot 1.8L 5 1 1204016 Spray nozzle for water tank 6 1 1204015 Water tank complete 1.8L 7 1 160821 (230V) Micro switch tank 1.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT DA-4 Drawing 6 Tank Float Strainer Cover Microswitch holder 5 27 28 26 7 2 1 25 8 16 3 4 15 14 13 12 10 20 25 21 22 23 17 18 24 9 19 40 11
EXPLODED VIEW FILTERBREW & SERVING CONCEPT DA-4 Spare parts list POS. Amount/Unit Part No. Description 1 4 120811 Warning plate 230V/95W 2 2 1204012 Lid of tank original 3 2 1204013 Strainer 4 2 1102016 Brew basket 1.8L 90 mm 5 2 160821 Micro switch tank 1.8L 6 2 1204015 Water tank complete 1.8L 7 2 1505041 Silicon hose hot 1.8L 8 2 1505021 Silicon hose cold W 1.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT DM-4 Drawing Tank Float Strainer Cover Microswitch holder 6 5 7 2 8 1 12 3 4 9 10 14 25 26 20 15 21 22 23 16 15 17 18 24 19 42 13 11
EXPLODED VIEW FILTERBREW & SERVING CONCEPT DM-4 Spare parts list POS. Amount/Unit Part No. Description 1 4 120811 Warming plate 230V/95W 2 2 1204012 Lid of tank original 3 2 1204013 Strainer 4 2 1102016 Brew basket 1.8L 90 mm 5 2 160821 Micro switch tank 1.8L 6 2 1204015 Water tank complete 1.8L 7 2 1505041 Silicon hose hot 1.8L 8 2 120422 Air inlet plastic 1.8L 9 1 1605651 Grommet power cable 10 2 1505021 Silicon hose cold W 1.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Mega Gold A Drawing 1 23 2 26 25 3 24 11 8 4 7 9 6 10 5 14 21 12 22 18 17 19 16 15 20 44 13
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Mega Gold A Spare parts list POS. Amount/Unit Part No. Description 1 1 1204012 Lid 2 1 1204013 Strainer 3 1 1204015 Water tank complete 1.8L 4 1 1204016 Spray nozzle for water tank 5 4 140339 Clip for hose 16.4mm 6 1 1505041 Siliocn hose hot W 1.8L 7 1 1205101 Brewing element 230V/2200W 8 1 160212-03 Over heating protection 9 1 1206123 Non return valve 1.8L 10 1 160821 Micro switch tank 1.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Mega Gold M Drawing 1 2 3 11 8 4 9 7 6 10 5 12 18 21 19 16 15 20 46 17 13 14
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Mega Gold M Spare parts list POS. Amount/Unit Part No. Description 1 1 1204012 Lid 2 1 1204013 Strainer 3 1 1204015 Water tank complete 1.8L 4 1 1204016 Spray nozzle for water tank 5 4 140339 Clip for hose 16.4mm 6 1 1505041 Siliocn hose hot W 1.8L 7 1 1205101 Brewing element 230V/2200W 8 1 160212-03 Over heating protection 9 1 1206123 Non return valve 1.8L 10 1 160821 Microswitch tank 1.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos Office Drawing 2 Tank Float Strainer Cover Microswitch holder 3 6 4 1 8 7 5 11 10 12 13 18 9 19 17 16 14 15 20 48
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos Office Spare parts list POS. Amount/Unit Part No. Description 1 1 1102016 Brew basket 1.8L 90 mm 2 1 1204012 Lid of tank original 3 1 1204013 Strainer original 4 1 160821 Micro switch tank 1.8L 5 1 1204016 Spray nozzle for water tank 6 1 1204015 Water tank complete 1.8L 7 1 1505041 Silicon hose hot 1.8L 8 1 1561036 Over flow hose 1.8L 9 1 1505021 Silicon hose cold W 1.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos A Drawing Tank Float Strainer Cover Microswitch holder 2 1 6 3 4 27 28 26 8 7 5 25 9 22 13 14 10 15 12 11 20 23 24 19 21 50 16 17 18
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos A Spare parts list POS. Amount/Unit Part No. Description 1 1 1102016 Brew basket 1.8L 90 mm 2 1 1204012 Lid of tank original 3 1 1204013 Strainer original 4 1 160821 Micro switch tank 1.8L 5 1 1204016 Spray nozzle for water tank 6 1 1204015 Water tank complete 1.8L 7 1 1505041 Hot water hose 1.8L 8 1 1561036 Drainage hose 1.8L 9 1 1505022 Inlet hose 500mm 10 1 1505021 Silicon hose cold W 1.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos M Drawing Tank Float Strainer Cover Microswitch holder 2 3 6 4 1 8 7 5 22 13 9 12 11 10 20 14 15 19 21 52 16 17 18
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Thermos M Spare parts list POS. Amount/Unit Part No. Description 1 1 1102016 Brew basket 1.8L 90 mm 2 1 1204012 Lid of tank original 3 1 1204013 Strainer original 4 1 160821 Micro switch tank 1.8L 5 1 1204016 Spray nozzle for water tank 6 1 1204015 Water tank complete 1.8L 7 1 1505041 Hot water hose 1.8L 8 1 1561036 Over flow hose 1.8L 9 1 1505021 Silicon hose cold W 1.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Cater Drawing 1 2 3 6 5 7 4 9 11 10 13 15 18 20 16 17 26 19 14 21 22 24 30 23 25 8 27 37 32 12 54 31 33 29 28 35 36 34
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Cater Spare parts list POS. Amount/Unit Part No.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Tower Drawing 6 2 1 8 9 3 4 10 11 12 7 13 14 5 15 16 17 18 20 19 22 36 23 35 24 25 26 21 27 34 29 30 40 38 56 39 33 37 31 32 28
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Tower Spare parts list POS. Amount/Unit Part No.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Grinder Original Drawing 1 2 3 4 5 7 6 11 12 10 13 20 19 18 17 14 16 21 8 15 9 58 22
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Grinder Original Spare parts list POS. Amount/Unit Part No.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT HVA Drawing 12 13 14 15 16 34 35 33 1 11 17 2 3 18 19 20 21 22 23 7 24 6 27 28 29 30 9 31 8 26 32 10 5 60 25 4
EXPLODED VIEW FILTERBREW & SERVING CONCEPT HVA Spare parts list POS. Amount/Unit Part No.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT V-2 Drawing 3 1 4 2 Spare parts list POS. Amount/Unit 1 1 2401101 Chassi V-2 2 6 120320 Rubber Feet 3 2 120811 Warming plate 230V/95W 4 2 C60900043 Power Switch Black 62 Part No.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Serving station 2.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Serving station 2.5L Spare parts list POS. PCS Part No. 1 1 1103351 Lid Cover with Tie 2 1 1103452 Brew-Thru Lid with SS Tube (2.5L) 3 1 1103453 Main housing with Upp 2.5L 4 1 1103455 Lower Housing 2.5L 5 1 1103456 Outlet Tube Jacket (2.5L) 6 1 1103457 Stand 2.5L 7 1 1103458 Drip Tray (2.5L serving station) 8 1 1103459 Glass Tube (2.
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Serving station 5L Drawing 1 13 17 2 8 9 10 3 15 16 4 5 11 12 6 7 14 14 65
EXPLODED VIEW FILTERBREW & SERVING CONCEPT Serving station 5L Spare parts list POS. PCS Part No.
DIMENSION FILTERBREW & SERVING CONCEPT A-2/M-2 A D E F B C Model A B C D E F A-2/M-2 595mm 205mm 410mm 428mm 578mm 360mm 67
DIMENSION FILTERBREW & SERVING CONCEPT DA-4/DM-4 E D C F B A Model A B C D E F DA-4/DM-4 410mm 410mm 428mm 595mm 578mm 360mm 68
DIMENSION FILTERBREW & SERVING CONCEPT Thermos A/M A D F C B Model A B C D F Thermos A/M 557mm 205mm 410mm 708mm 360mm 69
DIMENSION FILTERBREW & SERVING CONCEPT Mega Gold A/M E A B D C Model A B C D E Mega Gold A/M 655mm 205mm 445mm 390mm 806mm 70
DIMENSION FILTERBREW & SERVING CONCEPT Single Tower C D E A G F B Model A B C D E F G Single Tower 934mm 610mm 500mm 174mm 410mm 233mm 244mm 71
DIMENSION FILTERBREW & SERVING CONCEPT Tower B C D E A G F Model A B C D E F G Tower 934mm 928mm 500mm 174mm 410mm 233mm 244mm 72
DIMENSION SKETCH FILTERBREW & SERVING CONCEPT Single Cater/ Tea Cater A E D B C Model A B C D E Single Cater/Tea Cater 690mm 205mm 450mm 105mm 436mm 73
DIMENSION SKETCH FILTERBREW & SERVING CONCEPT Cater Brewing Brewing A E D B 74 C Model A B C D E Cater 690mm 410mm 450mm 105mm 436mm
DIMENSION FILTERBREW & SERVING CONCEPT Serving station 5L B C A D E Model A B C D E Serving station 5L 483mm 373mm 325mm 449mm 110mm 75
DIMENSION FILTERBREW & SERVING CONCEPT Serving station 2.5L A C D E B Model A B C D E Serving station 2.
DIMENSION FILTERBREW & SERVING CONCEPT V-2 C A D B E Model A B C D E V-2 62mm 359mm 230mm 189mm 198mm 77
DIMENSION FILTERBREW & SERVING CONCEPT HVA/HVM B D A E C Model A B C D E HVA/HVM 1 phase 500mm 225mm 410mm 240mm 210mm HVA/HVM 3 phase 500mm 225mm 410mm 240mm 210mm 78
DIMENSION FILTERBREW & SERVING CONCEPT Grinder Original A C B Model Grinder Original D A B C D 570mm 215mm 368mm 390mm 79
For the warranty to be valid the conditions for maintenance must have been followed according to our instructions, proper precaution has been made and warranty claim been issued without delay. The affected equipment may not be used during awaiting service if there is any risk that the damage or defect would worsen.