Installation manual

ManualsBrandsColeman ManualsDomestic Appliances36ECMII

DESA INTERNATIONAL

2701 INDUSTRIAL DRIVE PN 54024

P.O. BOX 90024 REV F

BOWLING GREEN, KY 42102-9004 6/02

www.desatech.com

SAVE THIS BOOK

This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also contains information that will

enable you to obtain replacement parts or optional accessory items when needed. Keep it with your other important papers.

36ECMII

36” Circulating Louvered Firebox

Includes: Manual Variable Control Fan S

stem, Combustion

Air Kit and Bi-Fold Doors with Brushed Brass finish

INSTALLATION INSTRUCTIONS

WARNING: ALWAYS LEAVE GLASS

DOORS FULLY OPENED OR FULLY CLOSED

WHEN OPERATING THIS FIREPLACE.

This fireplace is approved for use as a wood burning fireplace or for use with a vented gas log approved to ANS Z21.60, Z21.84 o

RGA 2-72 standards or for use with a vent-free gas log heater approved to ANS Z21.11.2 standard. A vent-free log can only be

installed in an aftermarket (completion of sale, not for purpose of resale from the manufacturer), permanently located, manufactured

(mobile) home, where not prohibited by local codes. A DESA hood must be installed when using a vent-free gas log heater (see

Accessories, p. 11)

This firebox meets the construction and safety standards of H.U.D. fo

application in mobile homes when installed according to these instructions.

ALL DIMENSIONS IN THIS MANUAL ARE IN

INCHES UNLESS OTHERWISE SPECIFIED

Summary of content (13 pages)

PAGE 1
36ECMII 36” Circulating Louvered Firebox Includes: Manual Variable Control Fan System, Combustion Air Kit and Bi-Fold Doors with Brushed Brass finish INSTALLATION INSTRUCTIONS SAVE THIS BOOK This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also contains information that will enable you to obtain replacement parts or optional accessory items when needed. Keep it with your other important papers.
PAGE 2
CONTENTS 1. INTRODUCTION --------------------------------------------------------------------------------- PG. 2 2. SELECTING LOCATION --------------------------------------------------------------------------------- PG. 2 3. MINIMUM CLEARANCES --------------------------------------------------------------------------------- PG. 2 4. FRAMING AND INSTALLING --------------------------------------------------------------------------------- PG. 3 5.
PAGE 3
• • • • WARNING: DO NOT INSTALL A FIREPLACE INSERT IN THIS BOX UNLESS THE MANUFACTURER’S INSTRUCTIONS WITH THE INSERT SPECIFICALLY STATE THIS FIREPLACE HAS BEEN TESTED FOR USE WITH THE INSERT. FOR YOUR SAFETY Do not store or use gasoline or any other flammable vapors or liquids in the vicinity of this or any other appliance. Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
PAGE 4
example, if the material selected has a K factor of 0.25, such as glass fiber, the following formula would apply. 0.25/0.84 x 1.0” = 0.30 thickness required. Thermal conductivity “K” of materials can be obtained from the manufacturer or supplier of the non-combustible material.] If the hearth extension is to be covered, use non-combustible material such as tile, slate, brick, concrete, metal, glass, marble, stone etc.
PAGE 5
FAN KIT ASSEMBLY (BK3) A fan kit assembly is preinstalled in this fireplace. Use of blowers or fans other than manufactured by DESA voids the warranty. The fan is operated by pressing the rocker switch located at the lower right hand corner of the fireplace face. Fan kit electrical connections are made through the electrical cover plate located on the side of the fireplace as shown in figure 6.
PAGE 6
If the adapter is needed, secure it onto the firestop using holes provided (see figure 10). The row of holes on the sides of the thimble is provided to allow for pitch variances. Position the firestop assembly and thimble to desired angle and secure with screws provided. Insert the thimble and firestop into the prepared opening and secure to the ceiling by nailing through the firestop flanges. The thimble should be even with or above the roofline.
PAGE 7
IMPORTANT: Terminations are required but can be installed once the manufactured house is sited. FLASHING INSTALLATION: (V6F-8DM or V12F-8DM) Determine the flashing to be used with the roof-opening chart. Slide flashing over pipe until base is flat against roof. Replace as many shingles as needed to cover exposed area and flashing base. Secure in position by nailing through shingles (see figure 12). DO NOT NAIL THROUGH FLASHING CONE.
PAGE 8
10 FOOT RULE: All flue gas outlet of chimney termination must extend a minimum of 3 feet in height above the highest point where it passes through the roof and must be at least 2 feet above the highest point of the roof that is within a horizontal distance of 10 feet (see figure 16). OPERATING GUIDELINES AND MAINTENANCE INSTRUCTIONS GLASS DOORS Glass doors are standard with the 36ECMII fireplace.
PAGE 9
A vent-free log may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes. *Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer. FOR PERMANENTLY LOCATED (SITED) HOMES ONLY: OPTIONAL GAS LINE INSTALLATION GAS LINE HOOK UP SHOULD BE DONE BY YOUR SUPPLIER OR A QUALIFIED SERVICE PERSON. NOTE: BEFORE YOU PROCEED, MAKE SURE YOUR GAS SUPPLY IS TURNED OFF.
PAGE 10
FIRESTOP SPACERS: (3600FS-8DM) 3. Firestop spacers are required at each point where the chimney penetrates a floor space. Their purpose is to establish and maintain the required clearance between the chimney and the combustible materials. When the pipe passes through a framed opening into a living space above, the firestop must be placed onto the ceiling from below as shown in figure 21. Figure 22 Figure 21 INSTRUCTIONS WHEN ELBOW OFFSET OF CHIMNEY IS NEEDED: (30E-8DM) TO INSTALL ELBOWS 1.
PAGE 11
FIREPLACE FACE EXTENSION: (FE-36) A fireplace face extension is available for use with this fireplace as an optional part. To install, secure the fireplace face extension to the top of the fireplace face with four self-drilling screws (provided) as shown in figure 25. Figure 26 WARNING: Risk of fire! Replace grate with DESA model 36 GR grate only. This grate has been designed to keep the operation of your fireplace safe and efficient.
PAGE 12
REPLACEMENT PARTS ACCESSORY PARTS VENT KIT PART NUMBERS SEE BELOW VENT KITS - USE FOR MOST COMMON MANUFACTURED (MOBILE) HOME INSTALLATIONS CONTENTS CPMH-A/AC CPMH-ACA CPMH-A/ACB 36-8DM 36" Double Wall Pipe 2 1 2 24-8DM 24" Double Wall Pipe 1 3 0 18-8DM 18" Double Wall Pipe 0 0 2 FST-A Adjustable Firestop Thimble 1 1 1 6F-8 Roof Flashing 1 1 1 VSC1-8DM Storm Collar 1 1 1 RTL-8DM Round Cap Termination 1 1 1 8' vent kit 11 9' vent kit 9' vent kit
PAGE 13
P/N 035-16689-000