COLOR RAY REMOTE CONTROL DEVICE Coloronix, Inc. 5461 West Jefferson Boulevard Los Angeles, California 90016 (323) 677-4242 http://www.rgbw.com Page 1—Coloronix Color Ray Manual V1.
Coloronix, Inc. © 2011 Coloronix, Inc. All rights reserved. According to copyright laws, this manual may not be copied—partially, or wholly— without the written consent of Coloronix, Inc. Despite full effort to avoid any clerical or printing inaccuracies, Coloronix, inc. accepts no responsibility for any such inaccuracies to be found in this manual. Coloronix, Inc. 5461 West Jefferson Boulevard Los Angeles, California 90016 Tech Support: (909) RGBW-555 http://www.rgbw.
Contents Summary 4 Introduction 4 Scope 4 Who is this manual intended for? 4 Additional Supplies 4 Safety 5 Purpose of Product 5 Hazard Icon Key 5 Specifications 5 Planning for Installation 6 Unpacking 6 Preparation 6 Points to Consider About Data 6 Color Ray Stand Alone Mode 7 Electrical Connection 8 Mounting 9 Data Connection 9 Troubleshooting Guide 10 Further Troubleshooting 10 Replacing Failed Fixture 10 Warranty Information 11 Page 3—Coloronix Color Ray Manual V1.
Summary Introduction Color changing fixtures are active, top-of-the-line color changing fixtures. They draw on solid-state elements in order to produce highlights and washes in architectural spaces. When installed and operated according to this manual, these fixtures will operate safely and dependably for their rated lifespan. A Color Ray Signal from the internal stand-alone controller or external controller can be used as well.
Safety Purpose of Product To control Coloronix color changing fixtures using on board Color Ray programs. Hazard Icon Key: The “ DANGER” icon means avoiding pending danger will result in serious injury, or death. The “ WARNING” icon means avoiding this warning may result may in serious injury, or death. The “ CAUTION” icon means not exercising caution here may result in minor to moderate injury, or property damage.
Planning for Installation Unpacking The Color Ray Receiver and Remote Control is shipped assembled with no additional assembly needed—they are shipped in separate packages. Any optional accessories are included in the package. Use the packing list located on the outside of the box to ensure all accessories are included. Survey the unit to make sure the units are all intact—not cracked or damaged.
Color Ray Stand Alone Mode For application not using Color Ray control, user can access preprogrammed shows. The fixture’s on board computer has been pre-configured with Color Ray programs. No additional software or hardware is needed to access. Program p. 1 p. 1 p. 1 p. 1 p. 6 p. 6 p. 6 p. 6 p. 4 p. 4 p. 4 p. 4 p. 2 p. 2 p. 2 p. 2 p. 3 p. 3 p. 3 p. 3 p. 5 p. 5 p. 5 p.
Electrical Connection NOTE: Supply lead wires should not be connected to a dimmer of any sort. Installing Your Color Ray Receiver 1. Prepare Wires: Note: Make sure the low-voltage wiring is installed at the wall box that will house the Color Ray receiver. • Be sure that the ends of the wires from the wall box are straight—cut if necessary. • Remove 5/8” or 1.6 cm of insulation from each wire in the wall box. 2. Connect CAT5/RJ45 Cable to Receiver Coupler 3.
Mounting 1. 2. 3. 4. 5. Turn off the power at the circuit breaker or fuse. Carefully position all wires so that there is room for the wall box for the dimmer. Mount the dimmer into the box with the supplied mounting screws. Attach the wallplate. Complete the installation by restoring power at the circuit breaker or fuse. Data Connection Fixtures on a serial data link must be daisy chained in one single line.
Troubleshooting Guide If light does not turn ON and ON/OFF LED does not turn on, check if: Lamp is burned out. Lamp neutral connection is not wired. If does not light, check if: Electrical power is not connected. Electrical power is less than specific voltage. Electrical power is greater than specified voltage. If control operation flickers or is intermittent, check if: Color Changing fixtures or final DMX device in daisy chain is not terminated. DATA cable is damaged.
Warranty Information 3 YEAR PRODUCT LIMITED WARRANTY Coloronix, Inc. provides a warranty to LED fixtures in case of physical or assemblyrelated malfunctions. This warranty is valid up to three years from the product’s purchase date. Furthermore, Coloronix, Inc. offers to repair products with no charge for labor, or at its own discretion, may offer to replace parts at no charge. However, any labor to remove or install fixtures is not covered.
