MSDS

ManualsBrandsColour Crete ManualsPaint1 gal. Gray Semi-Transparent Water-Based Concrete Stain

COLOUR CRETE™ MSDS

PAGE 1 OF 9

MATERIAL SAFETY DATA SHEET

Prepared to U.S. OSHA, CMA, ANSI and Canadian WHMIS Standards

PART I What is the material and what do I need to know in an emergency?

1. PRODUCT IDENTIFICATION

TRADE NAME (AS LABELED): COLOUR CRETE™

CHEMICAL NAME/CLASS

: Aqueous Polymer Mixture

SYNONYMS:

None

PRODUCT USE

: Concrete Stain

SUPPLIER/MANUFACTURER'S NAME

: Preserva Products Ltd.

ADDRESS

: 12860 Earhart Avenue,

Auburn, CA 95602

EMERGENCY PHONE

: 800-797-2537 M-Th, 9am-4pm PST

BUSINESS PHONE

: 800-797-2537 M-Th, 9 am-4pm PST

EMAIL ADDRESS FOR PRODUCT INFORMATION

: info@preservaproducts.com

DATE OF PREPARATION

: April 14, 2011

NOTE: ALL WHMIS required information is included in appropriate sections based on the ANSI Z400.1-2004 format. This product has been classified in accordance with the hazard criteria of

the CPR and the MSDS contains all the information required by the CPR.

2. HAZARD IDENTIFICATION

EMERGENCY OVERVIEW: Product Description: This product is somewhat viscous pigmented liquid with a slight polymer

odor. Health Hazards: Inhalation overexposures to the vapors of this product can cause irritation of the respiratory system. Eye

contact can cause moderate to severe irritation. Skin contact may be irritating, especially if contact is prolonged. Ingestion may cause

central nervous system effects. Ingestion of large quantities may be harmful. Flammability Hazards: This product is not flammable

or combustible. If involved in a fire, this product will release smoke, acrid vapors and toxic gases (i.e., carbon oxides, oxides of

nitrogen). Reactivity Hazards: This product is not reactive. Release of this product to the environment may cause harm to plants

and animals. Emergency Response Considerations: Emergency responders must wear proper personal protective equipment (and

have appropriate fire protection) suitable for the situation to which they are responding.

3. COMPOSITION and INFORMATION ON INGREDIENTS

CHEMICAL NAME CAS # % w/v

Proprietary Polymer 10.0-20.0%

Proprietary Acrylate Copolymer 3.0-7.0%

Proprietary Glycol Ether 64742-54-7 1.0-5.0%

Water 68.0-86.0%

PART II What should I do if a hazardous situation occurs?

4. FIRST-AID MEASURES

PROTECTION OF FIRST AID RESPONDERS: Rescuers should be taken for medical attention if necessary. Remove or cover gross

contamination to avoid exposure to rescuers.

DESCRIPTION OF FIRST AID MEASURES

: Contaminated individuals must seek medical attention if any adverse effect occurs. Take

a copy of label and MSDS to physician or health professional with the contaminated individual.

Skin Exposure: If this product contaminates the skin and irritation develops, immediately begin decontamination with soap and water. Remove

exposed or contaminated clothing, taking care not to contaminate eyes. The contaminated individual must seek medical attention if adverse effects

continue after flushing.

Eye Exposure

: If this product enters the eyes, open victim's eyes while under gently running water. Use sufficient force to open eyelids. Have victim

"roll" eyes. Minimum

flushing is for 20 minutes. The contaminated individual must seek medical attention if adverse effect occurs after flushing.

Inhalation

: If vapors, mists, or sprays of this product are inhaled, remove victim to fresh air. If necessary, use artificial respiration to support vital

functions. Seek medical attention if adverse effect occurs after removal to fresh air.

Ingestion

: If this product is swallowed, CALL PHYSICIAN OR POISON CONTROL CENTER FOR MOST CURRENT INFORMATION. DO

NOT INDUCE VOMITING, unless directly by medical personnel. Have victim rinse mouth with water or give several cupfuls of water, if conscious.

Never induce vomiting or give diluents (milk or water) to someone who is unconscious, having convulsions, or unable to swallow

. If vomiting

occurs, lean patient forward or place on left side (head-down position, if possible) to maintain an open airway and prevent aspiration.

IMPORTANT SYMPTOMS AND EFFECTS: See Sections 3 (Hazard Identification) and 11 (Toxicological Information).

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE

: Acute or chronic respiratory conditions, skin disorders, or disorders

involving the “Target Organs” (see Section 11, “Toxicological Information”) may be aggravated by overexposure to this product.

IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED: Treat symptoms and eliminate overexposure.

Summary of content (9 pages)

PAGE 1
MATERIAL SAFETY DATA SHEET Prepared to U.S. OSHA, CMA, ANSI and Canadian WHMIS Standards PART I What is the material and what do I need to know in an emergency? 1. PRODUCT IDENTIFICATION TRADE NAME (AS LABELED): CHEMICAL NAME/CLASS: SYNONYMS: PRODUCT USE: SUPPLIER/MANUFACTURER'S NAME: ADDRESS: COLOUR CRETE™ Aqueous Polymer Mixture None Concrete Stain Preserva Products Ltd.
PAGE 2
5. FIRE-FIGHTING MEASURES FLASH POINT : Not flammable. AUTOIGNITION TEMPERATURE: Not applicable. FLAMMABLE LIMITS (in air by volume, %): Not applicable. FIRE EXTINGUISHING MEDIA: Fire extinguishing materials that can be used against fires of this product include carbon dioxide, dry chemical powder, or appropriate foam. Consideration for surrounding materials must be taken into account. UNSUITABLE FIRE EXTINGUISHING MEDIA: None known.
PAGE 3
8. EXPOSURE CONTROLS - PERSONAL PROTECTION (Continued) EXPOSURE CONTROLS: CHEMICAL NAME CAS # EXPOSURE LIMITS IN AIR ACGIH-TLVs TWA STEL ppm ppm Proprietary Glycol Ether NE = Not Established. 20 NE OSHA-PELs TWA STEL ppm ppm 50 (skin) 25 (vacated 1989 PEL NE NIOSH-RELs TWA STEL ppm ppm 5 (skin) NE NIOSH IDLH ppm OTHER 700 DFG MAKs: TWA = 10 [sum of the concentrations of] (skin) PEAK = 2•MAK 15 min.
PAGE 4
10. STABILITY and REACTIVITY (Continued) POSSIBILITY OF HAZARDOUS POLYMERIZATION: Will not occur. CONDITIONS TO AVOID: Avoid extreme temperatures, incompatible chemicals. See Section 7 (Handling and Storage) for additional cautionary information related to materials contaminated with this product. PART IV Is there any other useful information about this material? 11.
PAGE 5
11. TOXICOLOGICAL INFORMATION (Continued) TOXICITY DATA (continued): PROPRIETARY GLYCOL ETHER (continued): TDLo (Oral-Rat) 1575 mg/kg/7 days-intermittent: Liver: other changes; Blood: other hemolysis with or without anemia, changes in spleen TDLo (Oral-Mouse) 5180 mg/kg/2 weeks-continuous: Endocrine: changes in thymus weight TDLo (Oral-Mouse) 9440 mg/kg/8 days-intermittent: Related to Chronic Data: death TDLo (Oral-Mouse) 198.45 gm/kg/21 weeks-continuous: Related to Chronic Data: death TDLo (Oral-Mouse) 37.
PAGE 6
11. TOXICOLOGICAL INFORMATION (Continued) REPRODUCTIVE TOXICITY INFORMATION (continued): A mutagen is a chemical that causes permanent changes to genetic material (DNA) such that the changes will propagate through generational lines. An embryotoxin is a chemical that causes damage to a developing embryo (i.e. within the first eight weeks of pregnancy in humans), but the damage does not propagate across generational lines.
PAGE 7
15. REGULATORY INFORMATION (Continued) ADDITIONAL U.S. REGULATIONS (continued): CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT (PROPOSITION 65): No component of this of product is on the California Proposition 65 lists. ADDITIONAL CANADIAN REGULATIONS: CANADIAN DSL/NDSL INVENTORY STATUS: The components of this product are listed on the DSL Inventory. OTHER CANADIAN REGULATIONS: Not applicable.
PAGE 8
DEFINITIONS OF TERMS (Continued) HAZARDOUS MATERIALS HAZARD RATINGS (continued): IDENTIFICATION SYSTEM NATIONAL FIRE PROTECTION ASSOCIATION HAZARD RATINGS (continued): FLAMMABILITY HAZARD (continued): 3 (Serious Hazard- Liquids and solids that can be ignited under almost all ambient temperature conditions.
PAGE 9
DEFINITIONS OF TERMS (Continued) NATIONAL FIRE PROTECTION ASSOCIATION HAZARD RATINGS (continued): INSTABILITY HAZARD (continued): 3 Materials that in themselves are capable of detonation or explosive decomposition or explosive reaction, but that require a strong initiating source or that must be heated under confinement before initiation: Materials that have an estimated instantaneous power density (product of heat of reaction and reaction rate) at 250°C (482°F) at or above 100 W/mL and below 1000 W/mL.