- Columbian Home Products, LLC Stainless Steel Bath Chairs Specification Sheet

INSE-85-20 1-3

Solutions for Daily Living

Contour Ultima™

Stainless Steel Bath Chairs

Models #8520, 8620, 8720, 8920

Thank you for Choosing Columbia!

Your Columbia Contour Ultima Stainless Steel Bath Chair has been built to the highest standards of quality to

ensure years of superior service. Please take the time to read these assembly instructions and pay particular

attention to the safety information provided. Thank you again for choosing Columbia!

Important Safety Instructions

When using your bath chair, always take basic safety precautions to reduce the risk of injury to persons.

1. Read and understand all instructions.

2. Determine, with a physician or therapist, the suitability of this product for the intended user.

3. To reduce the risk of injury or drowning, never leave the user unsupervised or unattended.

4. Check regularly that all tubing, bolts, buckles and other parts are tight at all times.

5. When in use, buckle up the user at all times.

Save These Instructions

Assembly of Your Contour Ultima Reclining Bath Chair

Your Contour Ultima comes fully assembled. After removing the chair from chair packaging, do not cut plastic

ties around adjustment bars. (The plastic ties help keep the adjustment lever bars in position.) The Ultima’s

frame is constructed from surgical grade stainless steel and the ComfortMesh™ cover is made with the highest

quality material. Non-slip pads protect the chair from slipping and from scratching the base of the bath. When

not in use, the chair can be folded flat for storage.

Assembling the Back Support (8720 & 8920 only)

1. Pull on the pull-tab and change the pivot angle to point straight up.

2. Remove bolts and nuts from post with an Allen Wrench and insert the U-shaped stainless steel back

support into the post and fasten with the bolts and nuts.

3. Insert end of Pull Handle into the small holes on the pull-tab for both sides. Press Stainless Steel Caps

over the Pull Handle's small end that will now be protruding from the pull-tab.

4. Pull the Pull Handles until Back Support and Calf Support are pointing straight up.

5. Slip the Bath Chair Cover over the Back Support, making sure the Pull handles are under the cover.

6. Place chair in are horizontal position, then turn chair upside down and fasten Velcro strap.

Setting the Angle of the Contour Ultima Bath Chair

The Contour Ultima is easy to adjust using the four simple adjustment lever bars, located on the front leg,

back leg, under the cover of the Chair’s back and under the cover of the Chair’s calf support. The legs, calf

support and back angles each adjust independently.

PAGE 1
Solutions for Daily Living Contour Ultima™ Stainless Steel Bath Chairs Models #8520, 8620, 8720, 8920 Thank you for Choosing Columbia! Your Columbia Contour Ultima Stainless Steel Bath Chair has been built to the highest standards of quality to ensure years of superior service. Please take the time to read these assembly instructions and pay particular attention to the safety information provided.
PAGE 2
8520, 8620, 8720, 8920 Contour Ultima Rev: 11.06 Adjustments to the Ultima should not be made while in use. Adjusting Back Angle: Locate the adjustment lever bar on the Chair’s back, under the cover (you do not need to remove the cover to operate the lever), and simply grip the lever and seat frame back and squeeze together. Then, with a lifting motion, adjust the back angle up or down.
PAGE 3
8520, 8620, 8720, 8920 Contour Ultima Maximum Weight Capacity DO NOT EXCEED MAXIMUM WEIGHT LIMIT Model 8520 100lb (45kg) Model 8620 130lb (59kg) Model 8720 180lb (81kg) Model 8920 250lb (113kg) Rev: 11.06 Angles of adjustment: * +/-3° • • Back to Seat Angles* - 0°, 30°, 60°, 90° Leg to Seat Angles* - 0°, -30°, -60° *Do not use -90° position. Cleaning Your Chair: Soapy water or mild cleansers may be used on all part of your bath support. Harsh abrasive cleaners (Ajax, Comet, etc.) may dull the finish.