User's Manual

In
stalling the Batteries
Wi
reless Keyboard and mouse use two AAA alkaline batteries,
Installing Batteries in the Mouse
Step1. Open the battery compartment.
Step2. Insert the batteries as shown inside the battery compartment.
Step3. Replace the cover.
Install the batteries in the keyboard
Step1. Remove the battery compartment cover on
the bottom of the keyboard by squeezing the
cover in from the tab to release it.
Step2. Insert the batteries as shown inside the battery
compartment.
Step3. Replace the cover.
Conn
ecting the Nano Receiver
St
ep1. Switch on your computer and connect the nano receiver to a free USB port.
Step2. Windows detects the USB receiver and installs it for use with the operating syetem
Step3 Smart-Link technology means that the mouse can be used immediately.
Power Saving Mode
The mouse automatically switches to power-saving mode when it is not moved for 8 minutes
Press the left or right to reactivate the mouse.
Storing the Nano Receiver
If neessary,the receiver can also be conveniently stored in the storage slot on the bottom of
mouse.
Functionality Problems
If the mouse or keyboard do not function as expected,ensure that you have carefulky checked
the following 1.The batteries are new and bave been inserted correctly
2.The receiver is correctly connected to the computer
3.The receiver and the devices are within their communication range(max.8m,depending on
local conditons)
Hot
keys on the keyboard
The
keyboard have 14 hotkeys located on the top of the keyboard and 3D scroll wheel.
Multimedia hotkeys
We
b home
E-m
ail
Pr
e-track
Next
-track
Play
/Pause
Mut
e
vlu
me up
Ca
lculator
volu
me down
sear
ch
Play
-stop
My
computer
Charge the Battery in Mouse or Keyboard.
Your mouse and keyboard use Two AAA size Ni-MH rechargeable Battery. Before you use the
mouse or keyboard, you need to place the mouse or keyboard on the stand to charge the Battery
for 10 hours. This is very important to battery life. Please make sure the charge indicator is light
ON when you charge the mouse.
When you feel your wireless mouse or keyboard is not working smoothly, that means that the
batteries need to be recharged. Please put the mouse or keyboard on the stand for charging.
Normally it will take 8 hours to get the Battery fully charged.
Place the mouse one the stand and make sure the charging indicator is light ON.
CAUTION: Some computer will turn off the power of USB port when entering sleep mode. In
this case, the battery inside the mouse or keyboard can not be charged. So you are
requested to keep your computer always ON when you charge the mouse or
keyboard
War
ning
1
:Cha
nges or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment
2
:
Thi
s equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

Reor
ient or relocate the receiving antenna.

I
n
crease the separation between the equipment and receiver.

Con
nect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

Cons
ult the dealer or an experienced radio/TV technician for help.
Model: CK356
G CM9135G
Ins
truction Manual
RF
Keyboard & Optical Mouse
CAUTION:
To use this device properly, please read the
user’s guide before installation.
Recer
iver
ZZZILQHSULQWFQ
FCC STATEMENT
1. This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.