Specifications

31
VonDuprinDoorcontrolandsecurityhardware•31
E7500Electricmortiselock
E7500Electricmortiselock
The electric mortise lock device has all the versatility and
advantages of the standard mortise lock device, plus the
advantage of being electrically controlled by a remote switching
device, an access control system or an automatic fire alarm
system. The device features the E7500 mortise lock. The E7500
controls the locking of the outside trim. When unlocked, the door
remains latched, preserving the fire rating of the door and making
it particularly useful where codes permit locking but require
unlocking during a fire emergency. The outside trim cylinder
retracts the latch bolt for mechanical override, night latch
function. Only available with TP, K or L functions.
The E7500 lock contains a SPDT signal to monitor the outside
trim condition (locked or unlocked) and a second SPDT signal
switch to monitor the latch bolt.
Standard features:
§ Field reversible handing
§ 24 VDC continuous duty solenoid
Optional features:
§ Fail safe (locked when energized, unlocked when de-energized
or during power failure). Specify with sux “FS.”
§ Fail secure (unlocked when energized, locked when de-
energized or during power failure). Specify with sux “FSE”
§ 24 VAC (with SO option)
§ 12 VDC
§ 12 VAC (with SO option)
Note: Some Fire codes will require “Fail Safe” (FS) operation for stairwell doors.Be sure to
specify the correct operation for your application.
Electrical specifications:
§ Solenoid — .60 AMPS @ 12VDC
.30 AMPS @ 24VDC
§ Each switch — Up to 2.0 AMPS @ 24VDC Maximum
The E option does not include the power transfer from door to
frame, the power supply or the control operator. (Refer to EPT-10
and PS902 or PS914 power supply)
To order, specify:
1. Use prefix “E,” example E9975.
2. FS or FSE
3. Voltage and current.
Electric mortise lock device
Adaptable for openings where continuous latching is required
while the trim may be electrically locked or unlocked from a
remote location—stairwells, exterior doors, etc.
Minimum system requirements:
§ PS902
§ EPT-10
Allegion Connect
Allegion’s cross-category Connect features common interconnect
components to our electrified options. Allegion Connect is a quick
and easy way to connect power sources; all the way from your
power supply to locking device. There is no wire cutting; reducing
installation and maintenance time ultimately cutting cost. Aer
installation, Allegion’s Connect continues to provide benefits
throughout the lifetime of the opening by offering a service kit
for repairs or modifications in the future.
Features and benefits
• Quick: common connections reducing installation time
• Perfect Connections: these factory installed connectors
ensure the right wires match up every time
• Protective: the connectors protect the connection points
throughout the installation process and lifetime of the opening
• Interchangeable: all Allegion Connect products utilize the
same connectors
• Maintenance: you no longer need to cut away wire to
disconnect Allegion products, also available is a service kit
specifically for Connect products.
How to order
1. Specify CON for Connect electronic options
Example: EL-99-EO-CON (99 Series Electrified Latching exit only
with Connect connectors)
2. Specify harness length; Consult door manufacturer for harness length
3. Specify Von Duprin EPT10-CON or Ives 7200 power transfer hinge
Wire run options
Harness length
Connectors
on both ends
Connectors on one end,
crimped pins on the other end
6 Inches CON-6 CON-6P
12 Inches CON-12 CON-12P
26 Inches CON-26 CON-26P
32 Inches CON-32 CON-32P
38 Inches CON-38 CON-38P
44 Inches CON-44 CON-44P
50 Inches CON-50 CON-50P
192 Inches CON-192 CON-192P
Power Supply Wire Harness = Connectors on one end, stripped leads on the other end,
offering a direct connection to the power supply
6 Inches CON-6W - wire extension to power supply
Consult door manufacturer for harness length requirements.
Note: You will need to purchase a separate wiring harness to go from exit device to hinge/
EPT and an additional harness to go from hinge/EPT to power supply or access control
system. Harness part numbers with ordering information can be located in the Schlage,
Von Duprin and Falcon pricebooks. A service kit is available for order in the Schlage, Von
Duprin and Falcon pricebooks. Included in this kit are male end plugs, female end plugs
and pins to customize harnesses to your application.
Note: Must be ordered with exit devices and locks