FISH-EYE HD-SDI CAMERA, 5 MEGAPIXEL ART. HDCAM360A Please read this manual thoroughly before use, and keep for future reference Via Don Arrigoni, 5 24020 Rovetta S.Lorenzo (Bergamo) http://www.comelitgroup.com e-mail: export.department@comelit.
SAFETY PRECAUTIONS Please read before using The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of insulated dangerous Voltage within the product’s enclosure that may be sufficient magnitude to constitute risk of electrical shock to persons.
Product Feature 1. 2. HD CCTV 5 Mega Pixel. SDI output. 3. 4. 5. 6. HDMI output. CVBSx4 output. 360° and 180° panorama view. Virtual PTZ function. 7. 8. 9. 10. Auto Pan Function. Multiple screen display. Privacy mask. Motion tracking. 11. Built-in microphone.
Specifications Model 360° panoramic camera Signal System NTSC or PAL Pick up device 1/3.2” Color CMOS QSXGA (5Mega Pixel : 2592x1944) image sensor Synchronizing Internal Scanning System 2:1 Interlace S/N Ratio More than 51dB Electronic Shutter x3; x2; x1; AUTO; 1/100; 1/120; 1/250 White Balance Auto Diagonal 185° Angle of view Horizontal 185° Vertical 185° Gamma Correct 0.45 / 1 RS485 PELCO D / 9600 Video Output 4 channels CVBS / HDMI / SDI Lens Type Board lens 1.19 mm / F2.
Connections: ① ① ① ① ① ① ① ① ① 1 label 1 Camera 1 CVBS (BNC) output 2 label 2 Camera 2 CVBS (BNC) output 3 label 3 Camera 3 CVBS (BNC) output 4 label 4 Camera 4 CVBS (BNC) output 5 RS485 cable Purple + / White - 6 RCA cable Audio output to speaker or DVR audio input 7 Power cable 12 VDC jack 8 SDI cable SDI connector output (BNC gold color) 9 HDMI connector HDMI output to connect to a HDMI monitor 10 Microphone Pinhole type microphone built in 5
Package contents Camera Ceiling cover Ceiling screws Wall screws 6
This 360° camera can be installed into different co nfiguration thanks to its rich connection. You will have an overview of different scenario in the next pages. A) Scenario without DVR 1. The camera uses the SDI connector output or the HDMI connector to a HD-SDI monitor that has RS485 built in connector. The user points the remote controller to the monitor and controls the camera 2.
RS485 connection with keyboard The 360° camera is set in protocol PELCO-D and baud rate 9600. User can use keyboard, DVR or any RS485 device to control 360° camera. Ex.: Keyboard RS 485 port RS 485 cable RS 485 port 1 Purple + positive RJ 11 pin 3 +, pin -- White - negative How to setup connection between keyboard and camera Press MENU button of keyboard for function setup CAM : 001< MUX : 00 DV : 00 1. Keyboard ID Setup Setup Menu 2. Master Setup >. System Menu 3. CAM Type setup. CAM Menu 4.
like PTZ dome to do Up / Down / Left / Right movement. Controls on screen in mode 5: 1. 2. 3. 4. Press 1 + CAM to call camera 1 and after use joystick to move. Press 2 + CAM to call camera 2 and after use joystick to move. Press 3 + CAM to call camera 3 and after use joystick to move. Press 4 + CAM to call camera 4 and after use joystick to move. Get in menu: press 95 + PRESET to call menu. Use joystick to select items. Up / Down for item chooses, Right to enter in sub items.
RS485 remote controller 10
Before to control the device, please set the RS485 parameters. Press RS485 set button into RS485 menu. Press to change control mode LCD mode: user operates the function by remote control. See LCD key define DVR mode: user operates the function by remote control. See DVR key define PTZ mode / 360° mode: user operates the function by remote control.
Remote controller key define Key Define LCD power ON / OFF RS485 menu setup LCD / DVR / CAM OSD item select Up / Down / Left / Right key DVR playback status LCD / DVR / CAM control mode switch Call desire LCD / DVR / CAM Device Menu Displays the LCD source information LCD volume setup LCD audio soundless VGA mode auto adjust Quit desired DVR OSD setup or number wrong typing LCD Direct select the AV1 source input N/A Direct select the VGA source input For HDMI Jump to Picture in Picture screen display Pict
Picture in picture screen source exchange Picture ratio selection: Under / Full / Over DVR Channel sequence Quad screen selection 9 split screen selection 16 channel selection Jump to playback mode Manual recording Jump to time search of playback mode Jump to backup mode CAM (P/T/Z dome; 360° mode) PTZ dome ID selection / Set, Call, Clear Preset DVR full channel selection FOCUS PTZ dome’s lens in manual focus PTZ dome’s lens in manual focus IRIS PTZ dome’s lens in manual Iris PTZ dome’s lens in manual I
ZOOM Control PTZ dome’s lens zoom in and out PRESET Set a Preset point Call a Preset point Clear a Preset point 14
RS485 connection with DVR RS 485 port RS485 + RS 485 cable Purple + positive RS485 - White - negative Protocol configuration: please go to your DVR RS485 (PTZ) setting. Select the camera and 360° It depends on which channel SDI is connected. If camera is on channel 1, please make sure the address is from 1 to 4, choose protocol PELCO-D and baud rate 9600. Please go to your DVR PTZ control mode to start operate 360° camera.
Main menu structure Item Selection Description AE Submenu Auto exposure AWB Submenu Auto white balance setting BRIGHTNESS 1~9 Picture brightness adjust SATURATION 1~9 Picture saturation adjust MD Submenu Motion detection setting MASK Submenu Picture mask zone setting 00~09 Picture noise reduction setting NOISE REDUCTION AUTO: means that camera will adjust automatically the mode after a period of time (0, 3, 5, 10, or 15 seconds) DAY/NIGHT AUTO/DAY/NIGHT DAY: means that camera will
AE submenu AE 50 Hz / 60 Hz 50 Hz / 60 Hz SHUTTER SPEED x3; x2; x1; AUTO; 1/100; 1/120; 1/250 Return AWB submenu AWB AWB AUTO: the system automatically adjusts the auto white balance OFF: the auto white balance is disabled AWC SET To enable it, press direction one time it will adjust the auto-white control in 9 seconds, and the AWB will automatically turn off Return Motion detection submenu MD AREA ACTION ON/OFF AREA 1~4 XPOS 0000~1943 YPOS 0000~1943 WIDTH 0256~1943 HEIGHT 0256~1943
MASK submenu MASK MASK MODE OFF/ON AREA 1~4 XPOS 0001~1943 YPOS 0001~1943 WIDTH 0000~1943 HEIGHT 0000~1943 RETURN COLOR 1~5 TRANSP 1~3 RETURN PATTERN submenu PATTERN MODE1 Camera 1 + 360° view MODE2 Camera 2 + 360° view MODE3 Camera 3 + 360° view MODE4 Camera 4 + 360° view MODE5 Quad + 360° view MODE6 Camera 1 + Camera 3 + 360° view MODE7 See below for more details MODE8 180° in 16 :9 display MODE9 360° flat MODE10 180° + Camera 3 + Camera 4 MODE11 180° + 180° MODE1
Pattern Mode 7: in this mode user can choose among 4 different angle of view, each can have horizontal and vertical flexibility range View available 120° 140° Verticale 180° -5 +5 range Horizontal range 160° -5 +5 -3 +3 -1 +1 0 SYSTEM submenu SYSTEM CAMERA1 ON / OFF CAMERA2 ON / OFF CAMERA3 ON / OFF CAMERA4 ON / OFF LOAD DEFAULT Will reset the device to factory default RETURN 19
Command list For camera 1 to 4 it is possible to define 3 Preset points that will be use for the Preset Cruise (76 + Preset) and the Preset Sequence display (66 + Preset) To define Preset 1 on camera 1: Call camera 1 Select your preset view by adjusting with the joystick Press 1 then press PRESET button 3 sec until you hear a bip (OSD will display on screen POINT1) (Setting may differ from the type of RS485 device you are using) Same for the other preset Call Preset 95: displays the menu of the 360° camer a
Pattern description: PATTERN Preset cruise Preset sequence Motion tracking yes yes yes yes yes yes yes yes yes yes yes yes MODE 1 MODE 2 MODE 3 MODE 4 21
PATTERN Preset cruise Preset sequence Motion tracking yes yes yes yes yes yes no no no no no no MODE 5 MODE 6 MODE 7 MODE 8 22
PATTERN Preset cruise Preset sequence Motion tracking no no no yes yes yes no no no yes yes yes no no no MODE 9 MODE 10 MODE 11 MODE 12 MODE 13 23
Dimensions Via Don Arrigoni, 5 24020 Rovetta S.Lorenzo (Bergamo) http://www.comelitgroup.com e-mail: export.department@comelit.