Specification

ManualsBrandsComfort-Aire ManualsForced Air Furnaces83% AFUE 125,000 BTU Lowboy Rear Flue Oil Hot Air Furnace

Due to ongoing product improvements, specifications and dimensions are

subject to change and correction without notice or incurring obligations. Determining the

application and suitability for use of any product is the responsibility of the installer.

Additionally, the installer is responsible for verifying dimensional data on the actual product

prior to beginning any installation preparations.

Third party incentive and rebate programs have precise requirements as to product performance

and certification. All products meet applicable regulations in effect on date of manufacture;

however, certifications are not necessarily granted for the life of a product.

Therefore, it is the responsibility of the applicant to determine whether a specific

model qualifies for these incentive/rebate programs.

“This product complies with all California product

labeling laws including, but not limited to, the Safe

Drinking W

ater and Toxic Enforcement Act of 1986,

more commonly known as Proposition 65.”

SPECIFICATIONS

Cogurations

• Upow / Highboy

• Basement / Lowboy

• Horizontal / Counterow

Heat Exchanger

• Heavy-duty 14 gauge steel with a long lasting, high temperature

ceramic ber combustion chamber

• Easy access large diameter stainless steel cleanout ports

Cabinet

• Foil-faced high density fiberglass insulation reduces heat loss and sound

• Pre-painted steel for maximum durability

Blower

• Direct drive with slide-out design (upflow only)and quick plug-in wiring

• 4 speed PSC direct drive motors with dynamically balanced blower

wheel and resilient motor mounts for smooth and quiet operation

Burner

• High quality Beckett™ Flame Retention AFG Burner for efficient

combustion

• High efficiency PSC Burner motor to provide consistent operation

through all operating conditions

• Solid state ignition provides a consistent 10,000 volts for smooth

ignition

• Color coded wiring for easy service

• 40VA Transformer and cooling fan relay are factory wired for easy add-

on cooling installation

Venting

• Includes field installed barometric damper

• Optional sidewall vent kit available

Genisys

Advanced Burner Control

(Model: 7505B1500) features the following:

• Programmable valve-on delay and motor-off delay

• Three indicator lights for system monitoring and diagnostics

• Two communication ports for adding alarm contacts, programming

display, and/or future wireless communications

• Welded relay protection with redundant motor relays

• Limited reset and limited recycle

• Sleek, modern design

• Technician Pump Prime mode

PSC OIL FURNACES

83% - 84%

OUFB/OLFB/OLRB

ODFB/ODRB

ACCESSORIES

DESCRIPTION USED WITH CATALOG NUMBER KIT NUMBER

Clean Out Kit All models 1.841025 ABRSH380-3

Field Controls Side Wall Vent Kit * All Models See Note Below See Note Below

Combustion Air Kit All Models 1.841038 ABOOT571

Clean Out Cap Kit All Models 1.841037 ACAP570

Combustible Floor Base

ODFB95/ODRB95 1.841022 BASE537-1

ODFB125 1.841023 0

Note: * This can be ordered from Field Controls, part number SWG-5-CK61.

OUFB/OLFB/OLRB

ODFB/ODRB

HORIZONTAL/COUNTERFLOW: DIMENSIONS (IN.)

Model A B C D E F G H J K L M N P Q R S

ODFB95-D3-4A 59 20-1/2 20-1/2 18-1/4 18-1/4 1-1/4 1-1/4 18 18 1-1/4 1-1/4 32-1/2 10-1/4 3 41-1/2 3 14-1/2

ODFB-125-D5-3A 59 23-1/2 23-1/2 21-1/4 21-1/4 1-1/4 1-1/4 21 21 1-1/4 1-1/4 32-1/2 11-3/8 3 41-1/2 3 17-1/2

ODRB95-D3-4A 59 20-1/2 20-1/2 18-1/4 18-1/4 1-1/4 1-1/4 18 18 1-1/4 1-1/4 32-1/2 10-1/4 3 41-1/2 3 14-1/2

HORIZONTAL: CLEARANCES TO COMBUSTIBLES (IN.)

Model Front Above Rear Flue Bottom

ODFB95-D3-4A

24 1 1 7 1

ODFB-125-D5-3A

ODRB95-D3-4A 24 1 24 7 1

COUNTERFLOW: CLEARANCES TO COMBUSTIBLES (IN.)

Model Front Sides Rear Floor Above Flue

ODFB95-D3-4A

16 1 1

Non-Combustible

0 7

ODFB-125-D5-3A

ODRB95-D3-4A 16 1 1 0 7

SP-2M 6/20 CA-PAT-PSC_SPEC

83% OIL FURNACE AL83

1-800-448-5872

All specifications and illustrations subject to

change without notice and without incurring

obligations.

Page 8

DIMENSIONS (IN.)

Model A B C D E F G H J K L M N P Q R S

L83HF1D84/95E12-1 59 20-1/2 20-1/2 18-1/4 18-1/4 1-1/4 1-1/4 18 18 1-1/4 1-1/4 32-1/2 10-1/4 3 41-1/2 3 14-1/2

L83HF1D112/125E20-1 59 23-1/2 23-1/2 21-1/4 21-1/4 1-1/4 1-1/4 21 21 1-1/4 1-1/4 32-1/2 11-3/8 3 41-1/2 3 17-1/2

L83HR1D57/72E12-1

59 20-1/2 20-1/2 18-1/4 18-1/4 1-1/4 1-1/4 18 18 1-1/4 1-1/4 32-1/2 10-1/4 3 41-1/2 3 14-1/2

L83HR1D84/95E12-1

L83HR1D112/125E20-1 59 23-1/2 23-1/2 21-1/4 21-1/4 1-1/4 1-1/4 21 21 1-1/4 1-1/4 32-1/2 11-3/8 3 41-1/2 3 17-1/2

HORIZONTAL / COUNTERFLOW

HORIZONTAL POSITION

Model Front Above Rear Flue Bottom

L83HF1D84/95E12-1

24 1 1 7 1

L83HF1D112/125E20-1

L83HR1D57/72E12-1

24 1 24 7 1L83HR1D84/95E12-1

L83HR1D112/125E20-1

COUNTERFLOW POSITION

Model Front Above Rear Flue Sides Floor

L83HF1D84/95E12-1

16 0 1 7 1

Non-Combustible

L83HF1D112/125E20-1

L83HR1D57/72E12-1

16 0 1 7 1L83HR1D84/95E12-1

L83HR1D112/125E20-1

CLEARANCES TO COMBUSTIBLES (IN.)

Supply

Opening

Front View

Flue Pipe

(Front flue

models only)

Return

Opening

Top View

Knockouts for

suspending (4)

Flue Pipe

(Rear flue models only)

Back View

Return

Opening

Front

View

Flue Pipe

(Front flue

models only)

Flue Pipe

(Rear flue

models only)

Back View

Supply

Opening

Warranty—Lifetime on heat exchanger, 5 years on parts

(Some limitations apply; see printed warranty for details.)

www.marsdelivers.com

Summary of content (6 pages)

PAGE 1
OUFB/OLFB/OLRB ODFB/ODRB SPECIFICATIONS PSC OIL FURNACES Cofigurations • Upflow / Highboy • Basement / Lowboy • Horizontal / Counterflow 83% - 84% Heat Exchanger • Heavy-duty 14 gauge steel with a long lasting, high temperature ceramic fiber combustion chamber • Easy access large diameter stainless steel cleanout ports Cabinet • Foil-faced high density fiberglass insulation reduces heat loss and sound • Pre-painted steel for maximum durability Blower • Direct drive with slide-out design (upflow only)and
PAGE 2
MODEL NUMBER GUIDE O D F B 95 D 3 4A OIL O = OIL FURNACE REV CODE 4A = REVISION CODE 4A=75K-95K 3A=125K CONFIGURATION D = HORIZONTAL/DOWNFLOW H = HORIZONTAL/DOWNFLOW U = UPFLOW/HIGHBOY L = BASEMENT/LOWBOY CFM COOLING CFM 3 = 1200 CABINET 19.5” W COOLING CFM 4 = 1400 CABINET 19.5” W COOLING CFM 5 = 1200 CABINET 20.
PAGE 3
Model Horizontal / Counterflow Basement/Lowboy Upflow / Highway Description BLOWER PERFORMANCE DATA L83UF1D57/72E12- 83% CFM @ ext. static pressure - in W.C. Model Motor Size (hp) L83UF1DC84/95E16 Blower Size Temp.
PAGE 4
UPFLOW UPFLOW A B C D 4 E E UPFLOW: DIMENSIONS (IN.) 2E12-1 3% OIL FURNACE 19-1/2 18 30-5/8 Model 19-5/8 Supply A9-3/4 B C D E AL83 Flue Pipe 95E16-1 DIMENSIONS OUFB75-D3-4A (IN.
PAGE 5
HORIZONTAL/COUNTERFLOW: DIMENSIONS (IN.) Model A ODFB95-D3-4A 59 B C 83% OIL FURNACE D 20-1/2 20-1/2 DIMENSIONS (IN.
PAGE 6
OUFB/OLFB/OLRB ODFB/ODRB ACCESSORIES DESCRIPTION USED WITH CATALOG NUMBER KIT NUMBER Clean Out Kit All models 1.841025 ABRSH380-3 Field Controls Side Wall Vent Kit * All Models See Note Below See Note Below Combustion Air Kit All Models 1.841038 ABOOT571 Clean Out Cap Kit All Models 1.841037 ACAP570 ODFB95/ODRB95 1.841022 BASE537-1 ODFB125 1.841023 0 Combustible Floor Base Note: * This can be ordered from Field Controls, part number SWG-5-CK61.