User manual
6
Microphone DM10
Pair
To use a receiver and transmitter together, they must be
paired. All transmitters and receivers are default paired
at the factory and will work together.
NB! To prevent eavesdropping, a new code key must be
generated and transmitted between the units by pairing.
Transmitting/receiving of pairing information along
with a new code can be performed from any Comfort
Digisystem unit with a display.
To pair units without a display, see section
Pairing (via
pairing button)
for more information. Pairing information
or a new code key can be received by several activated
units.
Pairing (via menu)
1. Choose Communication - Pair
2. Select Receive info on one unit. Ready to
receive pairing info is shown in the display.
3. Select New code on the other unit; select Yes.
4. Generate new code and send info? is shown in the
display. Select Yes (Now both the channel and the
coding information have been sent, and sound
transfer is eavesdrop-secure).
5. To pair another unit into your coded system, select
Send info instead on one of your paired units.
Pairing (via pairing button)
(The only way of pairing units without a display, with the
pairing button)
You can activate the Pairing function via the pairing
button.
1. One brief press of the button opens the
Pairing
menu.
2. Two brief presses activate the Send info function.
3. One long press activates the Receive info function.
Mode
Here you can adjust the function button. If no choice
has been made, the microphone sends continuously the
sound it takes up.
More settings are possible, see below. The chosen set-
ting shows in the display. For more information about
the function indicator see
More functions
.
Mute switch
In this setting you can shut off the microphone so that
no sound is sent when you press the function button.
Mic. On/Off
Using the function Mic. On/Off, the internal microphone
and transmitter can be switched on/off by pressing the
function button.
Push to talk
DM10 only sends when you press the function button.
Push/Cont
In this setting DM10 works like described above under
Push to talk
, but by pressing the menu control down
(scrolling down) the microphone is switched to send
continuously the sound it takes up.
This function may be useful when it is impossible to
press the function button, e.g. during lectures or
presentations etc.
Settings
PIN code
Here you can turn the PIN code function on and off
(selected functions lock).
Under the menu item Change PIN you can create your
own PIN code.
Under the menu item Lock Select, you can select differ-
ent types of menu locks:
- Mode: Locks all functions in the “Function button”
menu (can be combined with the “Pairing” menu
item)
- Pair: Locks all pairing functions in the unit, as well
as the pairing button
- All menus: Locks all menus
- Hide PIN entry: When the PIN-code is enabled, it is
only possible to unlock the menu within 3 seconds
after starting the unit, by pressing the menu control.
The PIN code is needed to be able to unlock selected
functions when PIN code has been activated.
If you forget your PIN code, please contact your point of
purchase to unlock the unit.
Charge
Here you can activate the Auto Power Off function to
shut down the unit automatically during charging. If
Auto restart is activated, the unit will start up automati-
cally when the charger is disconnected or loses power.
Language
For selection of menu language.
Name
The text to be displayed is selected here. Choose sym-
bols with the menu control. Select to save and x to
close without saving. To move the cursor during editing,
use the symbols > and <.
Inputs
Choose which additional input should be used.
- Extern Mic (for external microphones, e.g. clip-on-
microphones)
- Line-in (e.g. for TV- or PC-cable)
When Line-in is activated and as soon as a cable is con-
nected to the DM10, it switches automatically to
continuous transmission, even if Push-to-talk or
Mic. On/Off was chosen before. Like this it is possible
to use a DM10 as a companion unit and as a multimedia
connection without having to switch modes.