Comfort Digisystem User manual SecureStream Technology Comfort Digisystem Receiver DT10 North America / English
User manual Table of contents Page 1) Regulatory information 3 2) Introduction Comfort Digisystem 4 3) Overview - Receiver DT10 4 4) Check the hearing instruments input 4 5) Getting started 5 6) Acoustic indication, sound signals 5 7) Modes in the Receiver DT10 6 8) Output for user with different input types and programs in the hearing instrument 6 9) Pairing 8 10) Trouble shooting 9 11) Technical data 9 12) Service and warranty 10 13) Radio range and channels 10 14) Important sa
1) Regulatory information Comfort Digisystem products are not to be used as a substitute to the hearing aids and should be used in accordance with the specifications and recommendations provided by your physician. WARNING! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE! Max output > 130 dB SPL (Sound Pressure Level). Could be very dangerous for your hearing.
2) Introduction to the Comfort Digisystem Thank you for choosing Comfort Digisystem. Our products are easy to use and give you crystal clear sound. Before using the product, please read this manual carefully. The Comfort Digisystem products feature SecureStream Technology – a unique, patented digital technology allowing eavesdrop-secure radio transfer in real time.
2b. If the hearing instrument is equipped with a DAI input (check with audiologist or hearing instrument manufacturer), no programming of the hearing instrument is necessary. The Receiver DT10 works with the Microphone (M) listening program on your hearing instrument. By setting up the Receiver DT10 with the Programmer DT05, the push-button on the Receiver DT10 can be used to select the listening mode: Radio only (R mode) or Radio + Hearing instrument microphone (R+M mode).
7) Listening modes in the Receiver DT10 The available listening modes in the Receiver DT10 can be setup in different configurations: R Default setting R+M Setup with Programmer DT05 is necessary R and R+M Setup with Programmer DT05 is necessary The Programmer DT05 is used to configure and enable or disable different listening modes in the Receiver DT10. The push-button on the Receiver DT10 is used to toggle between the activated listening modes.
Receiver DT10 with R+M mode enabled and R mode disabled The chart below shows the output (what the user can hear) when Receiver DT10 listening mode R+M is enabled, in combination with different input types and programs in the HI.
9) Pairing The Receiver DT10 can receive but not transmit pairing information. To pair the Receiver DT10 with your Comfort Digisystem transmitter the Receiver DT10 must be connected either to your hearing instrument or to the Programmer DT05. Press the push-button on the Receiver DT10 for 2 seconds to activate pairing mode. When pairing mode is activated, you receive an acoustic indication: • • Send the pairing information within 15 seconds. To interrupt pairing mode, briefly press the push-button.
10) Trouble shooting 11) Technical data Receiver DT10 The receiver does not start 1. Check that the correct listening program is selected on the hearing instrument. 2. Make sure the Receiver DT10 is correctly connected to the hearing instrument’s audio shoe. Also check the connection between the audio shoe and the hearing instrument. 3. Make sure all connecting surfaces are clean. 4. Check/replace the hearing instrument’s battery. 5. Remember to press the push-button briefly to switch the DT10 on.
12) Service and warranty 13) Radio range and channels Warranty extension Comfort Audio Inc. warrants this product sold to the first end user (buyer) against defects in materials or workmanship for the time period and as set forth below. Pursuant to this Limited Warranty, Comfort Audio will, at its own option, either (a) repair the product or the parts determined to be defective, using new or refurbished parts, or (b) provide you with a new, or at our option, a refurbished unit.
14) Important safety instructions Read these before using your product 17) Never use a transmitter or receiver set to a nonpermitted frequency. Check with the frequency authority in the country where the equipment is to be used. 1) Read these instructions. 18) The product contains sensitive electronic equipment and must be handled carefully. 2) Keep these instructions. 19) Never charge product in closed, unaired spaces such as handbags, cases or other closed storage bags. 3) Heed all warnings.
Manufactured by: Comfort Audio AB, Box154, SE-301 05 Halmstad, Sweden Tel. +46 (0)35 260 16 00 Fax +46 (0)35 260 16 50 Local US office: Comfort Audio Inc, 350 South Northwest Hwy, Ste 300 Park Ridge, IL 60068 USA T (847) 656 5450 usa@comfortaudio.com www.comfortaudio.us MA0367 Ver 1.
