Installation Guide

ManualsBrandsComfort Glow ManualsElectric Wall Heaters1,500-Watt Infrared Quartz Wall Heater

~ 4 ~

WALL MOUNTING REQUIRED

LOCATING HEATER:

This heater is designed to be mounted on a wall only. It will not operate as a freestanding heater and should not be

modified to do so. For convenience and efficiency, install heater:

1. Where all clearances can be maintained. (see Page 5)

2. Where there is easy access for operation, inspection and service.

3. Within 5 feet of proper electrical outlet.

4. Away from any doorway or water source such as tub, sink, etc.

5. Insure there is no existing electrical wiring, plumbing or other obstructions in the area chosen.

6. Wall must be flat and must be a solid surface.

7. In the coldest part of the room.

8. Mounting screws are included for Dry Wall mounting only, for other installations the installer or home owner is

responsible to insure that the heater is securely mounted to wall.

Failure to position the heater in accordance with the guidance provided or failure

to secure heater securely to the wall could result in property damage and personal

injury.

Summary of content (6 pages)

PAGE 1
WALL MOUNTING REQUIRED LOCATING HEATER: This heater is designed to be mounted on a wall only. It will not operate as a freestanding heater and should not be modified to do so. For convenience and efficiency, install heater: 1. Where all clearances can be maintained. (see Page 5) 2. Where there is easy access for operation, inspection and service. 3. Within 5 feet of proper electrical outlet. 4. Away from any doorway or water source such as tub, sink, etc. 5.
PAGE 2
INSTALLATION MINIMUM CLEARANCES TO COMBUSTABLES LEFT/RIGHT TOP BOTTOM FRONT REAR *12 Inches 39 Inches 39 Inches 39 Inches 0 Inches Top clearance is from top of the heater to ceiling or other combustible material Bottom clearance is from the bottom of heater to surface of carpet, tile or other combustible material. * A sidewall must be at least 18 Inches away from the side of heater. -Always maintain a 36 Inch clearance from any furniture, draperies or other combustible material.
PAGE 3
INSTALLATION Step 1 (Figure 1) DRY WALL: Using the screws and wall anchors provided install into drywall as shown. Check to insure screws are secure. STUD WALL: Using the screws provided install into drywall as shown. Check to insure screws are secure. CONCRETE WALL: Drill ¼ inch holes, insert # 12 wall anchors (not included) and secure to wall with #12 x 3 inch screws (not included). Check to insure screws are secure. Figure 1 Step 2 (Figure 2) Hook the heater into position.
PAGE 4
REQUIERE MONTAJE EN LA PARED UBICACIÓN DEL CALENTADOR: Este calentador solo está diseñado para ser montado en una pared. No funciona como calentador independiente y no debe ser modificado para hacerlo. Para comodidad y eficiencia, instale el calentador: 1. Donde todas las salidas puedan ser mantenidas (ver página 5). 2. Donde haya fácil acceso para la operación, inspección y servicio. 3. A una distancia de 5 pies de una toma eléctrica apropiada. 4.
PAGE 5
INSTALACIÓN DISTANCIAS MÍNIMAS CON RESPECTO A COMBUSTIBLES IZQUIERDA DERECHA PARTE SUPERIOR PARTE INFERIOR FRENTE PARTE TRASERA *12 Pulgadas 39 Pulgadas 39 Pulgadas 39 Pulgadas 0 Pulgadas El espacio libre superior es desde la parte superior del calentador hasta el techo u otro material combustible El espacio libre inferior es desde la parte inferior del calentador hasta la superficie de la moqueta, los azulejos u otro material combustible.
PAGE 6
INSTALACIÓN Paso 1 (Figura 1) PANEL DE YESO: Instale en un panel de yeso tal como se muestra, utilizando los tornillos y los anclajes que se proporcionan. Controle para verificar que los tornillos estén asegurados. PARED DE ENTRAMADO: Usando los tornillos provistos instalar en paneles de yeso como se muestra. Compruebe para asegurar tornillos son seguras.