PREPARING FOR INSTALLATION Before beginning assembly or operation of the product, make sure all paresis present: Compare pairs with package contents list any part Is missing or damaged. donor attempt to assemblage, installation operate the product Contradistinction service for replacement parts. UNPACKING 1. Remove heater from carton. 2; Remove all protective packaging applied to heater for shipping A. Verity all contents are present.
PREPARING FOR INSTALLATION AIR FOR COMBUSTION AND VENTILATION A carrion: THIS Heater shall not bie installed in a room or Space unless the required volume of indoor combustion ait is provided by the method described in the National Fuel Gas Code, ANSI F223. 7/NFPAS4, the international Fuel Gas Code; or applicable local codes: PRODUCING ADEQUATE VENTILATION All spaces incomes Tall into one of the three following ventilation classifications: 1. Unusually Tight Construction 2. Unconfined Space 3.
PREPARING FOR INSTALLATION DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION Determining if You Have d Confined or Unconfined Space Use this worksheet to determine if you have a confined or unconfined space. Space: Includes the foo min which you will install heater slip any adjoining rooms with odorless passageways hyperventilation grills bellwether rooms. 1: Determine the volume of the.space Length» Width x Height = tu. ft.
PREPARING FOR INSTALLATION Ventilation Air From Inside Building This fresh alr would come from adjoining unconfined space. Hyperventilating roan adjoining unconfined space, you must provide twe permanent openings: one within 12 in. of the'wall connecting the two spaces (see options | and 2, Fig. 1). You Cain also remove door into adjoining room (see option 3, Fig. 1). Follow the: National Fuel Gas Code PAN SANS 2223.1.
INSTALLATION BH NOTICE: This heater is intended for use-as supplemental heat: Use this heater along with:your primary heating system. Do not install this heater as your primary. heat source. 4 WARNING: A qualified technician must install heater, Follow all local codes. iY WARNING: Maintain the: minimum clearances. if possible, provide greater clearances from the floor, ceiling, ‘and adjoining wall than required. 71 CAUTION: This heater creates want air currents.
INSTALLATION INSTALLING FAN (Select models) IMPORTANT: Optional fin i not approved foreseeing KWP210 and KWANZAA series: wall heaters. Bh WARNING: Electrical Grounding Instructions Noncompliance is-equipped with a three-prong (grounding) plug far your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. 1. Wall pinpointed Retreat must be disconnected from gas supplant removed floorwalker before installing fan accessory.
INSTALLATION Fig. 11 © Operating Fan Fan Rocker Switch \ LOCATING HEATER This heater is designed to be mounted roar rapscallion a floor, using the Support Legs (Select Models). include: ed with select models. . Far convenience and efficiency install healer 1. Where there is easy access far operation, inspection: and service, 2.1n the coldest part of room. 3. Minimum of 3" away from furniture and draperies.
INSTALLATION Methods For Attaching Mounting Bracket To Wall A WARNING Seton opting, idling monogramming: verity heir location: needed nonfactual your ELECTRICAL, PLUMBING OR GAS LINES MAY BE IN WALL, antiparticle, Plumbencnsenicg parson Use anathema hast hole UN-sach end of mounting bracket to attach bracket do wall, Attach mounting bracket fo a wall only in‘one of two ways: 4.
INSTALLATION Attaching to Expansion Bracket Method For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls: (concrete freemasonry: 1: Drill holes at marked locations using bit. For solid walls {concrete or masonry), drill af least sidesplitting: 2. Fold'wall expansion bracket as shown in (See Fig, 17) 3: Insert wall expansion bracket (wings first) inch hole: Tap expansion bracket flush to wall.
INSTALLATION CONNECTING TO:GAS SUPPLY A WARNING: Qualified service technician interconnect heater to gas supply. Follow all local codes. A PORTENT: This appliance requires a NPT (National Pipe Thread) inlet connection to the pressure regulator. Never connect the heater to private (non-utility) gas wells, commonly know a8 wellhead gas. A WARNING: Donor over tighten gas connections: A CAUTION: Use:only new.
INSTALLATION Install sediment rap In supply ling rag shown Fig. 20+ Gas Connection {Bag Fig. 20) Place entrapment where tis Ta NET within highchair for cleaning: Place sediment trap what trapped matter is not likely to frees. A sediment trap traps moisture and contaminants: Loi This keeps them fragmenting into heater Controls.