VENT-FREE INFRARED Ozzie ® GAS WALL HEATER MODEL # Propane KWP210 Kwpg12 Haida KWp3g2 KWwpsaz Kwanzaas KWhs524 Natural Gas KWN209 KWN211 KWN213 KWN3g1 9 BKWN325 KWN521 KWN523 us 4 WARNING: This appliance is equipped for {natural or propane) gas: Field conversion snot ANS gritted. Gas Fired Room Heaters Volume Il: Invented Room Heaters WARNING: [THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE; PERSONAL INJURY OR LOSS OF LIFE.
A IMPORTANT SAFETY INFORMATION IMPORTANT: Read this owner's manual carefully dnd completely before trying to assemble, operate, or service this heater. Improper use of this healer tan cause serious injury. or death from burns, fire; explosion; electrical shock, dnd carbon monoxide poisoning, Installation repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by 4 professional Service person.
AA SAFETY INFORMATION A WARNING: Dino use any accessories not approved for Use with this heater. CALIFORNIA PROPOSITION 65 Fuels used in gas or gil fired appliances and the products of combustion of such: fuels contain chemicals known tithe state of California to cause cancer, birth defects or other reproductive harm. This:product contain chemicals; including lead and lead compounds, known to the state of California to cause cancer, birth defects or other reproductive harm. Wash hands after handling. 1.
PRODUCT FEATURES SAFETY PILOT This heater has apilobwith an Oxygen Depletion Sensing (ODS) safety showoff system. Thee ODS/pilot shuts off the heater if there is not highlighter fresh air and clits off main burner gag in the prevention flame aut LEG KIT(Select models) 2 support legs and 4 support leg screws are included for floor mounting the heater. Seepage 13: NOTE; This'is an optional accessory and is not required Tor operation of the heater, PIE.
PREPARING FOR INSTALLATION Before beginning assembly or operation of the product, make sure all paresis present: Compare pairs with package contents list any part Is missing or damaged. donor attempt to assemblage, installation operate the product Contradistinction service for replacement parts. UNPACKING 1. Remove heater from carton. 2; Remove all protective packaging applied to heater for shipping A. Verity all contents are present.
PREPARING FOR INSTALLATION AIR FOR COMBUSTION AND VENTILATION A carrion: THIS Heater shall not bie installed in a room or Space unless the required volume of indoor combustion ait is provided by the method described in the National Fuel Gas Code, ANSI F223. 7/NFPAS4, the international Fuel Gas Code; or applicable local codes: PRODUCING ADEQUATE VENTILATION All spaces incomes Tall into one of the three following ventilation classifications: 1. Unusually Tight Construction 2. Unconfined Space 3.
PREPARING FOR INSTALLATION DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION Determining if You Have d Confined or Unconfined Space Use this worksheet to determine if you have a confined or unconfined space. Space: Includes the foo min which you will install heater slip any adjoining rooms with odorless passageways hyperventilation grills bellwether rooms. 1: Determine the volume of the.space Length» Width x Height = tu. ft.
PREPARING FOR INSTALLATION Ventilation Air From Inside Building This fresh alr would come from adjoining unconfined space. Hyperventilating roan adjoining unconfined space, you must provide twe permanent openings: one within 12 in. of the'wall connecting the two spaces (see options | and 2, Fig. 1). You Cain also remove door into adjoining room (see option 3, Fig. 1). Follow the: National Fuel Gas Code PAN SANS 2223.1.
INSTALLATION BH NOTICE: This heater is intended for use-as supplemental heat: Use this heater along with:your primary heating system. Do not install this heater as your primary. heat source. 4 WARNING: A qualified technician must install heater, Follow all local codes. iY WARNING: Maintain the: minimum clearances. if possible, provide greater clearances from the floor, ceiling, ‘and adjoining wall than required. 71 CAUTION: This heater creates want air currents.
INSTALLATION INSTALLING FAN (Select models) IMPORTANT: Optional fin i not approved foreseeing KWP210 and KWANZAA series: wall heaters. Bh WARNING: Electrical Grounding Instructions Noncompliance is-equipped with a three-prong (grounding) plug far your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. 1. Wall pinpointed Retreat must be disconnected from gas supplant removed floorwalker before installing fan accessory.
INSTALLATION Fig. 11 © Operating Fan Fan Rocker Switch \ LOCATING HEATER This heater is designed to be mounted roar rapscallion a floor, using the Support Legs (Select Models). include: ed with select models. . Far convenience and efficiency install healer 1. Where there is easy access far operation, inspection: and service, 2.1n the coldest part of room. 3. Minimum of 3" away from furniture and draperies.
INSTALLATION Methods For Attaching Mounting Bracket To Wall A WARNING Seton opting, idling monogramming: verity heir location: needed nonfactual your ELECTRICAL, PLUMBING OR GAS LINES MAY BE IN WALL, antiparticle, Plumbencnsenicg parson Use anathema hast hole UN-sach end of mounting bracket to attach bracket do wall, Attach mounting bracket fo a wall only in‘one of two ways: 4.
INSTALLATION Attaching to Expansion Bracket Method For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls: (concrete freemasonry: 1: Drill holes at marked locations using bit. For solid walls {concrete or masonry), drill af least sidesplitting: 2. Fold'wall expansion bracket as shown in (See Fig, 17) 3: Insert wall expansion bracket (wings first) inch hole: Tap expansion bracket flush to wall.
INSTALLATION CONNECTING TO:GAS SUPPLY A WARNING: Qualified service technician interconnect heater to gas supply. Follow all local codes. A PORTENT: This appliance requires a NPT (National Pipe Thread) inlet connection to the pressure regulator. Never connect the heater to private (non-utility) gas wells, commonly know a8 wellhead gas. A WARNING: Donor over tighten gas connections: A CAUTION: Use:only new.
INSTALLATION Install sediment rap In supply ling rag shown Fig. 20+ Gas Connection {Bag Fig. 20) Place entrapment where tis Ta NET within highchair for cleaning: Place sediment trap what trapped matter is not likely to frees. A sediment trap traps moisture and contaminants: Loi This keeps them fragmenting into heater Controls.
OPERATION FOR YOUR SAFETY READ BEFORE LIGHTING Imm WARNING: If you donor follow these:instructions exactly, a fire or explosion may result A calling property.damage; personal life, A. This appliance Saga pilot which must be lighted using this Pie Ignite. When lighting the pilot, follow these instructions exactly, B. BEFORE LIGHTING sal all rand the appliance area for gas.
OPERATION Emma LIGHTING INSTRUCTIONS BREEDER If the control knob does not pop-p when released, stop and immediateness call your service technician or gas supplier. 8. International electric power to the appliance. 9, Turn control knob counterclockwise = 10 desired setting, Burner Patterns (Manual Control) wel woe MED We Bo re High fet | GRE sr Bo THERMOSTAT GAS CONTROL 1. TOPI Read the safety information:on the previous page: 2. Turnoff all electric power'to the appliance. 3.
OPERATION TTT LIGHTING INSTRUCTIONS ae Blini Patterns (Thermostatic Control) b &b OFF TURN OFF GAS TO APPLIANCE BEER 1. Turin off all lactic power tithe appliance if service is tp be performed; 2. Push in, gds control Karol slightly and tur clockwise
OPERATION INSPECTING BURNERS Check pilot flame pattern daily when in use and at least yearly by a:qualified service agency. PILOT FLAME PATTERN Fig. 26 shows a correct pilot flame pattern. Fig. 27 shows an incorrect pilot flame pattern. The incur feet pilot lame is not touching the thermoplastic. This Will cause the thermonuclear to ool, which shuts ihe heater off; If pilot flame patterns income ct: stun heater off (see "To Tur Off Gas lo Appliance on page 19) «see Troubleshooting pages 23 microlight 26.
CARE AND MAINTENANCE NOTE: Before servicing you will eed to remove the front panel of the Fig, 30x Front Panel Removal heater: There are 4. Philips head screws, 2 prithee left sideman ion the the fret panel to the heater [See Fig: 30): Alleyway the unit to cool for at East thirty minutes before attempting to remove the front panel. Awarding: Turn off heater, unplug electrical cord and lat cool before servicing.
TROUBLESHOOTING Aware: If = Shut off gas supply: «Dp not try to light any appliance. «Do not touch any electrical switch: do not use any phone in your building. = immediately call vouch gas supplier from a neighbor's phonic: Follow the gas supplier's instructions: « If you cannot reach your gas supplier, call the fire department. IMPORTANT: Operating heater where impurities in-air exist may create odors.
TROUBLESHOOTING PROBLEM ODS/pilot lights but flame goes out wham astral knob is released. POSSIBLE CAUSE 1: Control knob is not fully pressed in. 2: Control knob is not pressed in long-enough 3: Equipmentishutoffvalve is not fully.open. 4. Thermocoupletonnection is loose. 5. Thermonuclear damaged. 6: Control valve damaged. 7: Inlet gas pressure is too high CORRECTIVE ACTION 1. Press in control knob fully: 2 AF ODS pilot lights, Keep conchs! knob pressed in 30-60 seconds: 3.
TROUBLESHOOTING PROBLEM ‘White powder rest: due forming within bummer box Orion adjacent walls ‘or furniture; pet ado] 1. When heated; the vapors from furniture polish, wax carpet cleaners, elo. Win into white powder residue. CORRECTIVE ACTION 1: Turn heater off when using furniture polish, wax, anticlerical or gorilla products. Heater produces unwanted oars, 1: Healer is:burning vapors from paint, hair spray, glues, ele. See IMPORTANT state men, page 22. 2. Gas leak.
TROUBLESHOOTING classified i Faff is not spinning. (Select models) POSSIBLE CAUSE 1. There is nig power tithe fan. 2. Tinseltown "AUTO", 3. Fan motor is bad. CORRECTIVE ACTION 1. Verify fiat Is plugged in and sel to" MAN" or "AUTO, 2-Allow 5410 mittens for janitor engage. 3: Replace fan. Fan is making a {oud noise. (Select models) 1. Fan housing or blades aie dirty. 2..Fan rotation is blocked: 3. Defective far. "Cleaning Fan" page 22. 2: Verity wiry insist infant path; fan.
REPLACEMENT PARTS LIST Outplacement parts) call repercussion device department at 18 14:643:0778 B30 am. — 4.30 Bn. CST, Monday — Friday: LD WARNING: Only-Rise genuine replacement parts from the World Marketing of America; Ing: Using any parts other than the original replacement pants may result in property damage. personal injury overdependent.