Installation Instructions

INTENDED USE:
This product is intended for indoor residential and office
use only, not for industrial or other commercial
applications. Use only with electrical wiring that is in
good working order and that meets applicable codes
and ordinances. If you have any questions whether
your wiring is adequate, consult a qualified electrician.
While using your fan, you should follow the IMPORTANT
INSTRUCTIONS listed below. As part of those
instructions, we have used the word '
WARNING” to
indicate the level of hazard:
WARNING indicates a
hazard which, if not avoided, could result in injury or
death.
IMPORTANT INSTRUCTIONS
As with all electrical appliances, basic safety
precautions should always be followed to reduce the
risk of electric shock, fire, or injury to persons, including
the following precautions:
• Read all the instructions before using this fan.
• Use this fan only as described in this manual. Any
other use not recommended by the manufacturer
may cause electrical shock, fire or injury to
persons.
• Do not operate the fan with a damaged power cord
or after the fan malfunctions or has been dropped
in any manner.
• Use of extreme caution is necessary when any fan
is used by or near children, disabled persons or
pets and whenever the fan is left operating
unattended.
• Do not place the fan on a small, unlevel, uneven or
any surface which might allow fan to tip or fall.
• For proper operation, fan should be placed on a
smooth, non-combustible surface.
• Always unplug fan when not in use.
• Do not operate the fan with blade guards or any
safety device removed.
• Avoid the use of extension cords due to risk of fire.
If an extension cord must be used, the cord must
be minimum 14 AWG and rated not less then 1875
watts.
• Do not run power cord under carpeting. Do not
cover cord with throw rugs, runners or the like.
Arrange cord away from traffic area where it will not
be tripped over.
• Do not insert or allow any object to enter any
openings on the fan. Doing so may cause electric
shock and/or fire hazard.
WARNING: SHOCK HAZARD
Use your fan only in dry environments. This fan is not
intended for use in a bathroom, laundry area, or similar
locations, near sinks, washing machines, swimming
pools
or other sources of water. Never locate fan where
it may fall into a bathtub or other water receptacle. Do
not use in damp environments such as flooded
basements.
WARNING: HOT SURFACES
Do not touch fan motor when in use. This motor is hot
when in use, to avoid burns, do not let bare skin touch
hot surfaces.
WARNING: FIRE HAZARD
Fans have arcing or sparking parts inside. Do not use
near combustible materials or flammable gases
or
sources of heat. DO NOT USE in areas where gasoline,
paint or flammable materials are used or stored. To
prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not insert or allow
foreign
objects to enter any ventilation or exhaust opening
as this
may cause an electric shock, fire, or damage the fan.
WARNING: ELECTRICAL SHOCK HAZARD
Do not use with damaged cord or plug. Use with
adequate electrical system that is up to code.
CAUTION-TO PREVENT ELECTRIC SHOCK, this
appliance has a two prong plug that must be inserted
into a matching properly grounded outlet to reduce the
risk of electrical shock. This fan has a polarized plug
(one blade is wider then the other). To reduce the risk of
electric shock, this plug is designed to fit a polarized
outlet only one way. If the plug does not fit fully into the
outlet, reverse the plug. If the plug still does not fit,
contact a qualified electrician. Do not attempt to defeat
this safety feature.
DO NOT operate any fan with a damaged cord or plug
or after fan malfunctions, has been dropped or
damaged in any manner. Do not operate fan with a
broken blade, safety cage or any visual imperfections.
For repairs covered under warranty, see warranty
statement. For all other repairs contact Comfort Zone's®
Customer Service by telephone or mail for information
and assistance.
DO NOT run power cord under carpeting. DO NOT cover
cord with throw rugs, runners or the like. Arrange cord
away from traffic area where it will not be tripped over.
Avoid the use of extension cords due to risk of fire. If an
extension cord must be used, the cord must be
minimum 14 AWG and rated not less then 1875 watts.
Do not use an extension cord unless the plug can be
completely inserted into its receptacle. Unplug the fan
when not in use. Do not operate fan with its ventilation
obstructed.
USAGE:
FAN OPERATION: Always operate the fan in the upright
position following all instructions and recommendations listed in
this manual FAN LOCATION: Place the fan in the area of the
room that will provide proper fan cooling. FAN CONNECTION:
Plug fan directly into 120 volt A.C., 60 Hz wall outlet. Be sure
plug fits tightly in outlet. A loose connection may cause
overheating and damage to the plug or fan. NOTE: To
prevent overloading a circuit, do not plug the fan into a
circuit that is servicing other electrical needs.
TURNING FAN ON/OFF: Place fan on stable level surface.
Plug fan into properly grounded outlet. To start the fan,
press desired speed button: 1-LOW, 2-MED, 3-HIGH. Press
0-OFF to discontinue use. Unplug fan when not in use.
OSCILLATION: To start fan oscillation, press Oscillation
Control Knob (located above motor housing) down. To stop
oscillation function pull Oscillation Control Knob up while
the fan is in any oscillation position.
Features:
• Wide Area Oscillation
• Push Button ON/OFF Switch with 3 Speed Settings
• High Performance Blade
• Adjustable Vertical Tilt
• Steel Safety Grill
• Long 6ft” Cordset
• 120V A.C. / 60Hz.
LIMITED WARRANTY
Products manufactured by Comfort Zone® are warranted to the original consumer to be free of
defects in material and workmanship for twelve (12) months from the original date of purchase. The
warranty does not cover products modified outside our factory, damage or failure caused by acts of
God, abuse, misuse, abnormal usage, faulty installation, failure to follow suggested maintenance
procedures enclosed with this product (as defined by Magnuson-Moss Warranty-Federal Trade
Commission lmprovement Act) This unit is guaranteed to the original retail purchaser against defects
in quality or workmanship for a period of one year from the date of original purchase. If this unit fails
because of a manufacturing defect within 30 days of purchase, return the unit, with your receipt, to the
retailer. After 30 days, but within the warranty period, if the unit was purchased within the continental
United States, return it, freight prepaid, to Comfort Zone® for repair or replacement. If the unit was
purchased outside the continental United States, return the unit to the place of purchase. This
warranty does not cover damage due to accidents, operation on other than 120 volts, 60 hertz, AC.
current, or any other abuse. All implied warranties, including the warranties of merchantability and of
fitness of purpose, if applicable, are hereby limited in duration to the period of one year from the date
of original retail purchase. Some States do not allow limitations on how long an implied warranty lasts,
so the above limitations may not apply to you. Incidental or consequential damages arising from a
breach of either express or implied warranties are hereby disclaimed and excluded. Some states do
not allow the exclusion of limitation of incidental or consequential damages, so this limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. No informal dispute settlement mechanisms are available. This limited warranty is given in
lieu of all other warranties.
Manufactured by:
Comfort Zone® 324A Half Acre Rd. Cranbury, NJ 08512 USA
800-221-6895 www.comfortzonefans.com
CARE AND MAINTENANCE
CLEANING: CAUTION-Before cleaning the fan be
sure
to disconnect power cord from the plug.
Clean the grill surface with a clean damp cloth. Do
not use harsh chemical or abrasive cleaners. DO
NOT IMMERSE THE FAN OR ANY WIRES IN
WATER. Replace front grill before fan use. Allow
fan to dry completely before use. Periodic grill
cleaning with a vacuum will prevent dust build up.
The motor is sealed and does not require any
interior maintenance, cleaning or lubrication.
MAINTENANCE: The Internal motor bearings are
permanently lubricated at the factory and do not
require any additional lubrication.
REPAIR: DO NOT OPERATE THE FAN WITHOUT
THE GRILL IN PLACE. DO NOT USE THE FAN IF
IT HAS MALFUNCTIONED OR BECOME
DAMAGED IN ANY WAY.
STORAGE: Keep original carton for storage of the
fan. Coil and tie the power cord to avoid damage
during storage.
Please Save These Instructions
®
12” Desktop Fan
Model #CZ121B
Assemble Rear Grille
onto Motor Housing.
Rear Grill should fit
into alignment pins on
fan motor housing as
shown. Note: Wire
Handle should be on
top.
Remove any
protective covering
over shaft before Fan
Blade installation.
Place Fan Blade onto
Motor Shaft. Notice
the pin on Motor Shaft
should fit into slots of
Fan Blade.
Thread Locknut onto Motor
Housing to lock Rear Grille in
place. Tighten=Clockwise
FAN ASSEMBLY: Assembly is required to use this fan.
Page 2
Page 4Page 3
OSCILLATION
CONTROL
Oscillation
Control
Knob
Place Power Cord wire through
opening of plastic Fan Base.
With cord opening properly
positioned, snap plastic Fan
Base onto fan body.
Re-assemble screws removed
in Step #1.
Step #2
Wire Goes
Through
Opening
and Guide
Remove two (2) screws from
base of fan and save them
for Step #2
Step #1
Screw
Screw
Step #4Step #3
Alignment
Pins
Step #5
T
i
g
h
t
e
n
Step #8
Press the three (3) Grille
Clips on Rear Grille to
securely attach to Front
Grille. Do not operate fan
without Grille in place.
Place Front Grille with logo
facing upwards onto fan. Be
sure the Front Grille is inserted
into Rear Grill Support on the
bottom of Rear Grille. Do not
operate fan without Grille in
place.
Step #7
Rear
Grill
Support
On/Off
Speed Control
CONTROL
PANEL
Thread Blade Cap onto
threaded end of Motor
Shaft. Note: Threads are
reversed at this connection.
Tighten=Counter-clockwise.
Step #6
T
i
g
h
t
e
n
Fig. #1 Fig. #2 Fig. #3
FUSE REPLACEMENT:
1. Grasp plug and remove from the receptacle or other
outlet device. Do not unplug by pulling on cord.
2. Open fuse cover by sliding open fuse access cover
on top of attachment plug towards blades. See Fig. #2.
3. Remove fuse carefully. Use a small tool to pry the end
of the fuse from holder cavity. Be careful not to break
glass window.
4. Replace fuse. WARNING: Risk of fire. Replace fuse
only with identical 5.0 Amp, 125 Volt fuse (3.6mm x
10mm). Be sure fuse is properly seated within its cavity.
5. Close fuse cover by sliding it back to its original
closed position.
Slide Cover to Open
Black border shows
page size and should
not print
Black border shows
page size and should
not print