Use and Care Manual

Page 1 (cover) Page 2 (inside)
Page 3 (inside) Page 4 (back)
Black border shows
page size and should
not print
Black border shows
page size and should
not print
11.0"
8.50"
Features:
• 70
o
Oscillation
• Two Heat Settings:
800 watts
400 watts
• Top Mounted Control Panel
• Safety Tip-Over Switch
• Quiet Operation
• Slip Twin-Tube Design
• Stay Cool Body
• 120V A.C. 60Hz., 6.66A, 2730 BTUs
®
Flat Panel Halogen Heater
Model #CZHTV9
Wing-Nut
Wing-Nut
Tip-Over
Switch
Wing-Nut
Wing-Nut
Wire Slot
USAGE:
HEATER OPERATION: Always operate the heater in
the upright position following all instructions and
recommendations listed in this manual HEATER
LOCATION: Place the heater in the area of the room that
is coldest. HEATER CONNECTION: Plug heater directly
into 120 volt A.C., 60 Hz wall outlet. Be sure plug fits
tightly in outlet. A loose connection may cause
overheating and damage to the plug or heater. NOTE:
To prevent overloading a circuit, do not plug the
heater into a circuit that is servicing other electrical
needs. Make sure heater is at least three (3) feet
away from walls, furniture, and other obstacles.
TURNING HEATER ON: The heater has two heat
settings: 400 and 800 watts. Rotate Control Dial to
desired setting. Use the 800 watt setting to raise the
room temperature quickly. Use the 400 watt setting to
maintain the room temperature. To use the Oscillation
feature simply choose the SWING function on the
LOW or HIGH setting. (During the heaters initial use,
you may experience a slight odor or smoking. This is
the result of residual lubrication on the steel “burning
off”. This is normal and will go away after a few
minutes of use.)
Switch HIGH: provides 800 watts of heat output with
TWO tubes Illuminated
Switch LOW: provides 400 watts of heat output with
ONE tube illuminated
Switch SWING: Oscillates the heater on LOW or HIGH
setting.
TO TURN HEATER OFF: Rotate Control Dial to the
OFF position. Unplug unit when not in use.
CARE AND MAINTENANCE
CLEANING: CAUTION-Before cleaning the heater be
sure to disconnect power cord and allow the heater to
cool completely. This heater should be cleaned at least
once a year to maintain proper performance. Clean
the outside surface with a clean damp cloth. Do not
use harsh chemical or abrasive cleaners. DO NOT
IMMERSE THE HEATER IN WATER. Allow heater to
dry completely before use.
REPAIR: DO NOT OPERATE THE HEATER WITHOUT
ANY OF THE SAFETY FEATURES IN PLACE. DO NOT
USE THE HEATER IF IT HAS MALFUNCTIONED OR
BECOME DAMAGED IN ANY WAY.
STORAGE: Keep original carton for storage of the
heater. Store the power cord to avoid damage during
storage.
BASE ASSEMBLY INSTRUCTIONS:
1. Turn the heater upside down.
2. Remove two wing-nuts from base of heater and
save for future re-assembly. (Fig.1)
3. Align tip-over switch of heater to round opening in
base and align power cord of heater to slot on base.
Assemble base to heater. (Fig. 2)
4. Using two wing-nuts removed in step #1, thread
onto heater as shown in Fig. 3.
LIMITED WARRANTY
Products manufactured by Comfort Zone are warranted to the original consumer to be free of defects
in material and workmanship for twelve (12) months from the original date of purchase. The warranty
does not cover products modified outside our factory, damage or failure caused by acts of God,
abuse, misuse, abnormal usage, faulty installation, failure to follow suggested maintenance
procedures enclosed with this product (as defined by Magnuson-Moss Warranty-Federal Trade
Commission lmprovement Act) This unit is guaranteed to the original retail purchaser against defects
in quality or workmanship for a period of one year from the date of original purchase. If this unit fails
because of a manufacturing defect within 30 days of purchase, return the unit, with your receipt, to the
retailer. After 30 days, but within the warranty period, if the unit was purchased within the continental
united States, return it, freight prepaid, to Comfort Zone. for repair or replacement. If the unit was
purchased outside the continental united States, return the unit to the place of purchase. This
warranty does not cover damage due to accidents, operation on other than 120 volts, 60 hertz, AC.
current, or any other abuse. All implied warranties, including the warranties of merchantability and of
fitness of purpose, if applicable, are hereby limited in duration to the period of one year from the date
of original retail purchase. Some states do not allow limitations on how long an implied warranty lasts,
so the above limitations may not apply to you. Incidental or consequential damages arising from a
breach of either express or implied warranties are hereby disclaimed and excluded. Some states do
not allow the exclusion of limitation of incidental or consequential damages, so this limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. No informal dispute settlement mechanisms are available. This limited warranty is given in
lieu of all other warranties.
Comfort Zone®
1 South Middlesex Avenue
Monroe Township, NJ 08831 USA
www.comfortzoneheaters.net
INTENDED USE:
This product is intended for indoor residential and office
use only, not for industrial or other commercial
application. Use only with electrical wiring that is in
good working order and that meets applicable codes
and ordinances. If you have any questions whether
your wiring is adequate, consult a qualified electrician.
Use your heater only with a working smoke detector
located in the vicinity of your heater.
While using your heater, you should follow the
IMPORTANT INSTRUCTIONS listed below. As part of
those instructions, we have used the word
'WARNING” to indicate the level of hazard:
WARNING indicates a hazard which, if not avoided,
could result in injury or death.
IMPORTANT INSTRUCTIONS
As with all electrical appliances, basic safety
precautions should always be followed to reduce the risk
of electric shock, fire, or injury to persons, including the
following precautions:
• Read all the instructions before using this heater.
• Use this heater only as described in this manual. Any
other use not recommended by the manufacturer
may cause electrical shock, fire or damage to
persons or property.
• Do not operate the heater with a damaged power
cord or after the heater malfunctions, has been
dropped in any manner. Return heater to authorized
service facility for examination, electrical or
mechanical adjustment or repair.
• Do not leave heater unattended when in use. Use of
extreme caution is necessary when any heater is
used by or near children, disabled persons or pets
• Do not place the heater on a small, unlevel, uneven or
any surface which might allow heater to tip or fall.
• For proper operation, heater should be placed on a
smooth, non-combustible surface. Do not place on
rugs or carpet. Not for use outdoors or or in wet
areas.
• Always unplug heater when not in use.
• Do not operate the heater with heater guards or any
safety device removed.
• Do not operate without legs and wheels installed.
• Avoid the use of an extension cord because the
extension cord may overheat and cause a risk of fire.
However, if you have to use an extension cord, the
cord shall be No. 14 AWG minimum size and rated
not less than 1875 watts.
• Do not run power cord under carpeting. Do not cover
cord with throw rugs, runners or the like. Arrange cord
away from traffic area where it will not be tripped
over.
• To disconnect heater, turn controls off then remove
plug from outlet.
WARNING: SHOCK HAZARD
Use your heater only in dry environments. This heater is
not intended for use in a bathroom, laundry area, or
similar locations, or near sinks, washing machines,
swimming pools or other sources of water. Never locate
heater where it may fall into a bathtub or other water
container. Do not use heater outdoors. Do not use in
damp environments such as flooded basements.
WARNING: HOT SURFACES
Do not touch body of heater when in use. This heater is
hot when in use, to avoid burns, do not let bare skin
touch hot surfaces. If provided, use handles when
moving this heater.
WARNING: FIRE HAZARD
Heater has hot and arcing or sparking parts inside. Do
not use near combustible materials or flammable gases
or sources of heat. DO NOT USE in areas where
gasoline, paint or flammable materials are used or
stored. Keep combustible materials such as furniture,
pillows, bedding, papers, clothes and curtains at least 3
feet (.9 M) from the front of the heater and keep them
away from the sides and rear. To prevent a possible fire,
do not block air intakes or exhaust in any manner. Do
not use on soft surfaces, like a bed, where openings
may become blocked. Do not place the heater near a
bed because objects such as pillows or blankets can
fall off the bed and be ignited by the heater. Do not
insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock,
fire, or damage the heater. This heater contains
flammable materials and if ignited will support and
spread fires.
WARNING: ELECTRICAL SHOCK HAZARD
Do not use with damaged cord or plug. Use with
adequate electrical system that is up to code.
The supply cord has a polarized plug. As a safety
feature this plug will fit in a polarized outlet only one
way. To prevent electric shock, match wide blade of
plug to wide slot, fully insert plug. If the plug does not fit
contact a qualified electrician. Never use an extension
cord unless plug can be fully inserted. DO NOT attempt
to defeat this safety feature.
DO NOT run power cord under carpeting. DO NOT cover
cord with throw rugs, runners or the like. Arrange cord
away from traffic area where it will not be tripped over.
Avoid the use of an extension cord because the
extension cord may overheat and cause a risk of fire.
However, if you have to use an extension cord, the cord
shall be No. 14 AWG minimum size and rated not less
than 1875 watts. Do not use an extension cord unless
the plug can be completely inserted into its receptacle.
Unplug the heater when not in use. Do not operate
heater with its ventilation obstructed.
Save These Instructions
Fig.1
Fig. 2
Fig. 3
Rotary Control Dial
Round
Opening