Warranty

Page 1 (cover) Page 2 (inside)
Page 3 (inside) Page 4 (back)
Black border shows
page size and should
not print
Black border shows
page size and should
not print
11.0"
8.50"
Features:
•ON/OFF Switch with Speed Settings
•Adjustable Vertical Tilt
•Maximum Air Movement
•All Metal Construction
•Metal Fan Blades
•Safety Grills
•Long 5ft. Grounded Electrical Cord
•120V A.C. / 60Hz.
®
High Velocity Fan
Model #CZHV18B
#CZHV20B
USAGE:
FAN OPERATION:
Always operate the fan in the upright position following all instructions and
recommendations listed in this manual FAN LOCATION: Place the fan in the area of the room that will provide
proper fan cooling. FAN CONNECTION: Plug fan directly into 120 volt A.C., 60 Hz wall outlet. Be sure plug fits
tightly in outlet. A loose connection may cause overheating and damage to the plug or fan. NOTE: To prevent
overloading a circuit, do not plug the fan into a circuit that is servicing other electrical needs.
TURNING FAN ON: Place fan on stable level surface. Plug fan into properly grounded outlet. To start the
fan, turn the switch from the OFF position to the desired fan speed.
TURNING FAN OFF: To turn the fan off, turn the switch from the current fan speed setting to the off
position. Remove plug from outlet.
ADJUSTING FAN TILT: To adjust the tilt angle, use supplied knob wrench to loosen the adjustment screw.
After adjustment, retighten the adjustment screw. Save knob wrench for future use.
FAN CRADLE ASSEMBLY: Simple assembly is required to use this fan.
1. Align CCradle Base (packed separately) with with support brackets attached to fan body sides. Note: you
may need to flex the parts to make them align properly.
2. Insert support bracket into opening of Cradle Base. Press spring loaded button down to allow it to insert
into Cradle Base, see Fig 1.
3. Press support bracket into Cradle Base until spring button protrudes out open hole in Cradle Base, see Fig.
2.
4. Repeat above process for opposite side of fan.
INTENDED USE:
This product is intended for indoor residential and office
use only, not for industrial or other commercial
applications. Use only with electrical wiring that is in
good working order and that meets applicable codes
and ordinances. If you have any questions whether
your wiring is adequate, consult a qualified electrician.
While using your fan, you should follow the IMPORTANT
INSTRUCTIONS listed below. As part of those
instructions, we have used the word '
WARNING ” to
indicate the level of hazard:
WARNING indicates a
hazard which, if not avoided, could result in injury or
death.
IMPORTANT INSTRUCTIONS
As with all electrical appliances, basic safety
precautions should always be followed to reduce the
risk of electric shock, fire, or injury to persons, including
the following precautions:
• Read all the instructions before using this fan.
• Use this fan only as described in this manual. Any
other use not recommended by the manufacturer
may cause electrical shock, fire or injury to
persons.
• Do not operate the fan with a damaged power cord
or after the fan malfunctions or has been dropped
in any manner.
• Use of extreme caution is necessary when any fan
is used by or near children, disabled persons or
pets and whenever the fan is left operating
unattended.
• Do not place the fan on a small, unlevel, uneven or
any surface which might allow fan to tip or fall.
• For proper operation, fan should be placed on a
smooth, non-combustible surface.
• Always unplug fan when not in use.
• Do not operate the fan with blade guards or any
safety device removed.
• Avoid the use of extension cords due to risk of fire.
If an extension cord must be used, the cord must
be minimum 14 AWG and rated not less then 1875
watts.
• Do not run power cord under carpeting. Do not
cover cord with throw rugs, runners or the like.
Arrange cord away from traffic area where it will not
be tripped over.
• Do not insert or allow any object to enter any
openings on the fan. Doing so may cause electric
shock and/or fire hazard.
WARNING: SHOCK HAZARD
Use your fan only in dry environments. This fan is not
intended for use in a bathroom, laundry area, or similar
locations, or near sinks, washing machines, swimming
pools
or other sources of water. Never locate fan where
it may fall into a bathtub or other water receptacle. Do
not use in damp environments such as flooded
basements.
WARNING: HOT SURFACES
Do not touch fan motor when in use. This motor is hot
when in use, to avoid burns, do not let bare skin touch
hot surfaces.
WARNING: FIRE HAZARD
Fans have arcing or sparking parts inside. Do not use
near combustible materials or flammable gases
or
sources of heat. DO NOT USE in areas where gasoline,
paint or flammable materials are used or stored. To
prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not insert or allow
foreign
objects to enter any ventilation or exhaust opening
as this
may cause an electric shock, fire, or damage the fan.
WARNING: ELECTRICAL SHOCK HAZARD
Do not use with damaged cord or plug. Use with
adequate electrical system that is up to code.
CAUTION-TO PREVENT ELECTRIC SHOCK, this
appliance has a three prong grounded plug that must be
inserted into a matching properly grounded outlet to
reduce the risk of electrical shock. Do not defeat this
safety feature.
DO NOT operate any fan with a damaged cord or plug
or after fan malfunctions, has been dropped or
damaged in any manner. Do not operate fan with a
broken blade, safety cage or any visual imperfections.
For repairs covered under warranty, see warranty
statement. For all other repairs contact Comfort Zone's
Customer Service by telephone or mail for information
and assistance.
DO NOT run power cord under carpeting. DO NOT cover
cord with throw rugs, runners or the like. Arrange cord
away from traffic area where it will not be tripped over.
Avoid the use of extension cords due to risk of fire. If an
extension cord must be used, the cord must be
minimum 14 AWG and rated not less then 1875 watts.
Do not use an extension cord unless the plug can be
completely inserted into its receptacle. Unplug the fan
when not in use. Do not operate fan with its ventilation
obstructed.
Fig. 2Fig. 1
Cradle
Base
Spring
Button
Spring
Button
Support
Bracket
Please Save These Instructions
Page 2
Page 4Page 3
LIMITED WARRANTY
Products manufactured by Comfort Zone® are warranted to the original consumer to be free of
defects in material and workmanship for twelve (12) months from the original date of purchase. The
warranty does not cover products modified outside our factory, damage or failure caused by acts of
God, abuse, misuse, abnormal usage, faulty installation, failure to follow suggested maintenance
procedures enclosed with this product (as defined by Magnuson-Moss Warranty-Federal Trade
Commission lmprovement Act) This unit is guaranteed to the original retail purchaser against defects
in quality or workmanship for a period of one year from the date of original purchase. If this unit fails
because of a manufacturing defect within 30 days of purchase, return the unit, with your receipt, to the
retailer. After 30 days, but within the warranty period, if the unit was purchased within the continental
United States, return it, freight prepaid, to Comfort Zone® for repair or replacement. If the unit was
purchased outside the continental United States, return the unit to the place of purchase. This
warranty does not cover damage due to accidents, operation on other than 120 volts, 60 hertz, AC.
current, or any other abuse. All implied warranties, including the warranties of merchantability and of
fitness of purpose, if applicable, are hereby limited in duration to the period of one year from the date
of original retail purchase. Some States do not allow limitations on how long an implied warranty lasts,
so the above limitations may not apply to you. Incidental or consequential damages arising from a
breach of either express or implied warranties are hereby disclaimed and excluded. Some states do
not allow the exclusion of limitation of incidental or consequential damages, so this limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. No informal dispute settlement mechanisms are available. This limited warranty is given in
lieu of all other warranties.
Manufactured by:
Comfort Zone®
324A Half Acre Rd., Cranbury, NJ 08512 USA
800-221-6895 www.comfortzonefans.net
CARE AND MAINTENANCE
CLEANING: CAUTION-Before cleaning the fan be
sure
to disconnect power cord from the plug.
Clean the grill surface with a clean damp cloth. Do
not use harsh chemical or abrasive cleaners. DO
NOT IMMERSE THE FAN OR ANY WIRES IN
WATER. Replace front grill before fan use. Allow
fan to dry completely before use. Periodic grill
cleaning with a vacuum will prevent dust build up.
The motor is sealed and does not require any
interior maintenance, cleaning or lubrication.
MAINTENANCE: The Internal motor bearings are
permanently lubricated at the factory and do not
require any additional lubrication.
REPAIR: DO NOT OPERATE THE FAN WITHOUT
THE GRILL IN PLACE. DO NOT USE THE FAN IF
IT HAS MALFUNCTIONED OR BECOME
DAMAGED IN ANY WAY.
STORAGE: Keep original carton for storage of the
fan. Coil and tie the power cord to avoid damage
during storage.
FUSE REPLACEMENT:
1. Grasp plug and remove from the receptacle or other
outlet device. Do not unplug by pulling on cord.
2. Open fuse cover by sliding open fuse access cover on
top of attachment plug towards blades. See Fig. #4.
3. Remove fuse carefully. Use a small tool to pry the end
of the fuse from holder cavity. Be careful not to break
glass window.
4. Replace fuse. WARNING: Risk of fire. Replace fuse
only with identical 5.0 Amp, 125 Volt fuse (3.6mm x
10mm). Be sure fuse is properly seated within its cavity.
5. Close fuse cover by sliding it back to its original closed
position.
Page 4
Fig. #5Fig. #4Fig. #3
Slide Cover to Open