CVM-WM100 PLUS UHF 1-Trigger-2 Wireless Microphone User Manual
Foreword Thanks for purchasing COMICA WM100 Plus wireless microphone; WM100 Plus is a wireless microphone with dual-transmitter triggered by one receiver, with two AA batteries.
Notice Transmitter should be used more than 10cm from Receiver, when the distance is less than 10cm, Receiver’s wireless signal receiving part will take protect action to shut down wireless signal receiving, then audio may be intermittent, which is normal; When using auto IR sync, please stay within 30cm, otherwise the signal may be so weak that the sync will not be successful; In the case of stereo/mono mode switch, please preset the mode before using to avoid the transient interference caused by switching
Package Contents Main Parts: Lavalier Transmitter (TX) Receiver (RX) Accessories: 1 3.5mm Mic Audio Input Cable x 2 pcs 6 Wind Muff x 2pcs 2 3.5mm-3.5mm Audio Output Cable x 1 pcs 7 USB power input cable x 1 pcs 3 3.
Components and Instruction Components Lavalier Transmitter (TX) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Antenna Working Status Indicator On-off / Muting Button SET Function Menu Function Selection Button LINE IN External Input IR Sensor Mic External Input IR Status Indicator Function Selection Button + Micro USB Port for External Charging Belt Clip 1/4 Thread Battery Tray 12 1 6 2 7 8 3 9 13 4 5 10 11 14 4
Receiver (RX) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Group A Antenna Group B Antenna Group A Working Status Indicator On-Off Button SET Function Button Function Selection Button 3.5mm Audio Input Jack IR Sensor 3.
Function Button Instruction Lavalier Transmitter / Receiver Long Press Power On / Off Short Press Muting Mode (the mute function can be activated only when the screen is lighted up ) Power / Muting Button Long Press SET Function Menu + Button - Button Short Press Enter the function adjustment menu 1.Confirm the selected function 2.
Indicator Light Instruction Normal Recording Status (This state is only for the Green Light Keeps On transmitter, when the channel matches successfully, the receiver Transmitter RF can pick up the sound) Red Light Keeps On Muting Mode Red Light Flicker Low-power reminder Channel matches Green Light Keeps On IR Red Light Flicker Green Light Keeps On Receiver A IR/RF B IR/RF Green Light Flicker (No matter the channel matches or not) Channel in the match...
Installation and Usage Preparation Before Usage (Transmitter Operating Steps same with Receiver) 1. Prepare Power Supply There're two ways of Power Supply, you can optionally choose AA batteries or External charging: 1.1 Install two AA batteries into the battery tray according to their positive and negative electrode.
1.
2.Belt Clip Installation Please install the belt clip according to the illustration if you require the way of connection.
3. Lavalier Transmitter Installation 3.1 Insert the 3.5mm audio input line into MIC socket 3.
3.3 Target the MIC to the audio source and check the working status according to the volume indicator on the screen H A Group A 570.875MHz A Audio Dynamic Display Bar 3.4 After the channel matching with the receiver, it can be used Please refer to screen operation instruction for channel matching.
4. Receiver Installation 4.1 Connect receiver to your video equipment through the camera mount 4.2 Connect one end of the 3.5mm-3.5mm audio OUTPUT cable to the OUTPUT port of WM200RX and another end to the AUDIO INPUT port of the camera or camcorder.Insert the headphone into the 3.5mm monitoring port for real-time monitoring and then long press power button to turn on the receiver. Most DSLR cameras has 3. 5MM port, if you use the XLR camcorder, you need to use the 3. 5mm-XLR audio output cable.
3.5mm Audio Output Monitoring Cable 3.5mm-3.5mm Audio Output Cable 3.5MM-XLR Audio Output Cable 4.3 After the channel matching with the receiver, it can be used Please refer to screen operation instruction for channel matching.
Screen Display and Operation Instruction Lavalier Transmitter Screen Display Instruction Signal Strength High Signal Strength Low H L Group A Normal recording Muting(Unlocking) Group B Muting Muting(Locking) H A Group A 570.
Operation Instruction 1.Manually Adjust the Channel of Transmitter 1.1 Long press button to CH setting display page H A Group A CH11 570.875MHz A 1.2 Short press button to select the channel H A Group A CH8 570.125MHz A 1.3 Short press button to confirm H A Group A CH8 570.
2.Group A/B Selection 2.1 Press button to ‘ Group Setting ’ display page H A Group Setting Group A A 2.2 Long press button to ‘ Group Setting ’ setting page H A Group Setting Group A A 2.3 Press button to select the group H A Group Setting Group B A 2.
3. Low Cut Filter ‘ Low/High/OFF ’ Adjustment 3.1 Press button to ‘ Low Cut Filter ’ display page H A Low Cut Filter OFF A 3.2 Long press button to enter ‘ Low Cut Filter ’ setting page H A Low Cut Filter OFF A 3.3 Press button to select LCF ‘ Low/High/OFF ’ H A Low Cut Filter Low A 3.4 Short press 18 button to confirm Low-cut function will filter out the low-frequency part of the audio source, such as the chirping and crowd noise, and the main audio source will be more crisp.
4.Transmitting Signal Strength ‘ High/Low ’ Adjustment 4.1 Press button to ‘ RF Power ’ display page H A RF Power High A 4.2 Long press button to ‘ RF Power ’ setting page H A RF Power High A 4.3 Press button to adjust the transmitting signal strength H A RF Power Low A 4.
5.Muting Mode Enable/ Disable 5.1 Press button to ‘ Muting ’ display page H A Muting Enable A 5.2 Long press button to ‘ Muting ’ setting page H A Muting Enable A 5.3 Press button to select Muting mode Enable/ Disable H A Muting Disable A 5.
When set to ‘ Disable ’, the muting function cannot be used, the icon is: When set to ‘ Enable ’, the muting function works, the icon is: The muting mode can be controlled only when the screen is on, press any button to light the screen and then press the button to switch the muting mode.
6.Backlight ‘ Lighting Time/Turn Off ’ Adjustment 6.1 Short Press button to ‘ Backlight ’ display page H A Backlight 15s A 6.2 Long press button to ‘ Backlight ’ setting page H A Backlight 15s A 6.3 Short press button to adjust the backlight lighting time or you can turn it off for power saving H A Backlight 60s A 6.
7. Reset to Defaults 7.1 Press button to ‘ Reset ’ display page H Reset No A 7.2 Long press button to enter ‘ Reset ’ setting page H Reset No A 7.3 Short press Settings A button to select whether to restore factory H Reset Yes A 7.4 Short press A A button to confirm and restore factory setting H A Reset Resetting......
8. Version 8.1 Press version button to ‘ Version ’ display page to check the H A Ve r s i o n 1.0.
Receiver Screen Display Instruction Group A Signal Strength Display Bar Group B Signal Strength Display Bar Power Indication Group A Channel of Group A Group A transmitting power A B Group A Group B CH 41 CH 11 A B Group B Channel of Group B Group B Transmitting power Group A Receiving Audio Status Indication Group B Receiving Audio Status Indication When Group A/B is on, the background color of the channel display icon is black; When Group A/B is off, the channel display icon is transparent and
Operation Instruction 1.Manually Adjust the Channel of Group A/ Group B 1.1 Long press button to 'CH' display page of Group A, and short press again to switch to 'CH' display page of Group B. A B Group A Group B CH 41 CH 11 A B 1.2 Short press button to select the channel A B Group A Group B CH 45 CH 11 A B 1.
2.Audio Output Mode ‘Stereo/Mono’ Adjustment 2.1 Press button to ‘ Output Mode ’ display page A B Output Mode Stereo A B 2.2 Long press button to ‘ Output Mode ’ setting page A B Output Mode Stereo A B 2.3 Press press button to select Mono/ Stereo Output Mode, Short button to confirm A B Output Mode Mono A B When one use only one Transmitter (Group A or Group B), the output of Receiver only work in Mono mode.
3.Group A/B Function Setting 3.1 Press button to ‘ Setting ’ display page A B Setting Group A A B 3.2 Long press button to ‘Group A / B Selection' Setting Page A B Setting Group A A B 3.3 Press button to select Group A/B to edit A B Setting Group B A B 3.
4.Group A/B ‘ On/ Off ’ Adjustment 4.1 Short Press A Setting ’ display page button to ‘ Group Power ON A B Group A Setting Power ON A B 4.2 Long press button to ‘ Setting ’ setting page A B Group A Setting Power ON A B 4.3 Short Press button to select ‘ Power Off ’ or not A B Group A Setting Power OFF A B 4.
5.Group A/B Volume Adjustment 5.1 Short Press A Setting ’ display page button to ‘ Group Volume A B Group A Setting Volume 12 A B 5.2 Long press button to ‘ Volume ’ setting page A B Group A Setting Volume 12 A B 5.3 Short Press button to adjust the volume A B Group A Setting Volume 8 A B 5.
6.Group A/B IR Sync button to ‘ Group A Setting ’ display page Sync 6.1 Short Press A B Group A Setting Sync A B 6.2 Long press button for IR Matching with transmitter A B Group A Setting Sync? YES A B 6.3 Use the button to select whether to match, and short press A B Group A Setting Matching...... A B to confirm, Matching OK A B Group A Setting Matched! A B While in IR matching, please make sure the IR sensor of transmitter and receiver point to point within 30cm, otherwise it may not succeed.
7. Backlight ‘ Lighting Time/Turn Off ’ Adjustment 7.1 Short Press button to ‘ Backlight ’ display page A B Backlight 60s A B 7.2 Long press button to ‘ Backlight ’ setting page A B Backlight 60s A B 7.3 Short press button to adjust the backlight lighting time or you can turn it off for power saving A B Backlight 30s A B 7.
8. Reset to Defaults 8.1 Press button to ‘ Reset ’ display page A Reset No A 8.2 Long press 8.4 Short press B button to enter ‘ Reset ’ setting page A Reset No A 8.3 Short press Settings B B B button to select whether to restore factory A Reset Yes A B B button to confirm and restore factory setting A B Reset Resetting......
9. Version 9.1 Press version 34 button to ‘ Version ’ display page to check the A Version 1.0.
Specification Lavalier Transmitter TX Channel 48 Duration 6 Hours Antenna 1/4 Wavelength Wire Antenna Stray Radiation <-60dBc Sound Delay <20ms Audio Distortion <0.5% Signal/Noise >65dB Audio Input Socket 3.5mm Socket Battery AA batteries×2pcs External Power Micro USB 5V/1A Group A/B Size 107 x 66 x 26.
Receiver RX Channel 48 Duration 6 Hours Signal/Noise >65dB Antenna 1/4 Wavelength Wire Antenna Sensitivity -90dBm Sound Delay <20ms Audio Distortion <0.5% Wireless Frequency 20Hz~18KHz Audio Output Socket 3.5mm Socket Battery AA batteries×2pcs External Power Micro USB 5V/1A Size 107 x 66 x 26.
CVM-WM100 PLUS UHF 一拖二无线麦克风 用户使用手册
前 言 感谢您购买COMICA/科唛 WM100 PLUS 无线麦克风; WM100 PLUS是一款一拖二无线麦克风,此款麦克风使用两节AA电池,采用UHF 无线调频技术及LCD高清点阵屏,16级可调音量,并融入了低切功能、红外对 码、立体声/单声道音频模式切换、RF信号强度可调、MIC/LINEIN输入、接 收端无线电量检测、拾音动态显示、背景灯光可调等多种功能,同时具备强 大的屏蔽抗噪性能,是一款广电级高品质麦克风; 为保证产品的顺畅使用及安全,请在使用前严格阅读本说明书,并正确组装 及操作。 产品主要功能 . . . . . . . . .
注意事项 正常使用时发射器应距离接收器10cm以上,当小于10cm时,接收器的无线信 号接收部分将会进行保护动作,从而关闭无线信号接收,音频可能出现间 断,此为正常现象; 进行红外对码时,请保持在30cm 距离之内,否则可能会导致通讯过弱、对码 不成功; 进行立体声/单声道切换时,请在使用前提前设置好,避免在使用过程中切换 带来的短暂电流干扰; 天线会影响工作距离,请保护好天线并勿进行人为损坏; 工作距离会受到周围环境的影响,使用过程中请尽量保持环境空旷无干扰, 并关闭机身自身的WIFI; 近距离使用该产品时,建议将此产品RF强度设置为“LOW”, 可降低功耗增 强续航; 用于手机拍摄时,客户须单独购买TRS-TRRS 音频转换线, 并注意将手机模式 设置为‘飞行模式’以避免来电干扰; (不支持部分安卓系统的原生态录音系统,建议此时于第三方APP模式下使 用); 请在干燥环境中对该产品进行储存; 不要在雨中或潮湿环境中使用该设备,否则会有短路的危险; 2
包装清单 主体: 领夹发射器(TX) 接收器 (RX) 配件: 1 3.5mm MIC音频输入线 X 2pcs 6 防风毛 X 2pcs 2 3.5mm-3.5mm 音频输出线 7 USB供电线 X 1pcs 3 3.
部件介绍及说明 部件说明 领夹发射器 1 2 3 4 5 6 7 8 9 10 11 12 13 14 天线 发射及工作状态指示灯 开关/静音按键 SET功能菜单选项 功能调节按键 LINE IN 输入接口 红外对码窗 MIC输入接口 对码状态指示灯 功能调节按键 + 外部供电Micro USB接口 腰带夹 1/4螺孔 电池仓 12 1 6 2 7 8 3 9 13 4 5 10 11 14 4
接收器 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 A通道天线 B通道天线 A通道工作状态指示灯 开/关按键 SET功能菜单选项 功能调节按键 3.5mm 音频输出接口 红外对码窗 3.
按键说明 长按 领夹发射器 /接收器 开机 / 关机 静音 开关/静音 按键 短按 (静音功能须在屏幕点亮 后才能开启生效) SET 功能菜单选项 长按 短按 功能调节按键+ 功能调节按键- 进入功能调节菜单 1.确定所选功能 2.
指示灯定义 正常录音状态 绿灯长亮 后,接收器方可拾音) RF 领夹 发射器 红灯长亮 静音状态 红灯闪烁 低电量提醒 绿灯长亮 IR A IR/RF (此状态仅针对发射器,频道匹配成功 频道配对后 (无论是否匹配成功) 红灯闪烁 频道配对中... 绿灯长亮 频道匹配成功后的正常工作状态 绿灯闪烁 频道匹配不成功 频道配对中...
安装与使用 使用前准备(发射器与接收器方式相同) 1. 两种供电方式的选择: 1.
1.
2.
3. 发射器安装 3.1 把3.5mm 音频输入线插入MIC插口 3.
3.3 将MIC 对准音源,根据屏幕上的音量指示条检测发射器是否正 常工作 H A Group A 570.875MHz A 音频动态显示条 3.
4. 接收器安装 4.
4.2 通过3.5mm-3.5mm 音频输出线插入OUTPUT接口把接收器与录影设 备连接,把耳机插入3.5mm 监听接口进行实时监听,长按电源开 关打开接收器 大多数DSLR相机使用的是3.5MM接口,如果使用XLR类型接口的摄像机, 需要使用3.5MM-XLR音频输出线. 3.5MM音频监听线 3.5mm-3.5mm 音频输出线 3.5MM-XLR频输出线 4.
屏显说明与操作说明 领夹发射器 屏显说明 信号强度强 信号强度弱 A/B通道 频道 H L 通道A 正常录音 静音功能解锁 通道B 静音 静音功能锁定 H A Group A 570.
操作说明 1.手动调节发射器 CH 频道 1.1 长按按键 进入CH 设置界面 H A Group A CH11 570.875MHz A 1.2 使用 按键选择本机频道 H A Group A CH8 570.125MHz A 1.3 短按 按键确定 H A Group A CH8 570.
2.A/B 通道选择 2.1 使用 按键调到“通道设置”界面 H A Group Setting Group A A 2.2 长按按键 进入“通道设置”界面 H A Group Setting Group A A 2.3 使用 按键选择本机通道 H A Group Setting Group B A 2.
3.低切“低/高/关闭”调节 3.1 使用 按键调到“低切”界面 H A Low Cut Filter OFF A 3.2 长按按键 进入“低切”设置界面 H A Low Cut Filter OFF A 3.3 使用 按键选择“低”、“高”或“关闭”音源低切功能 H A Low Cut Filter Low A 3.
4.发射功率调节 4.1 使用 按键调到“发射功率”界面 H A RF Power High A 4.2 长按按键 进入“发射功率”设置界面 H A RF Power High A 4.3 使用 按键调节发射信号强度 H A RF Power Low A 4.
5.静音模式开启/关闭 5.1 使用 按键调到“静音锁定”界面 H Muting Enable A 5.2 长按按键 进入“静音设置”界面 H Muting Enable A 5.3 使用 A A 按键选择开启/关闭静音功能 H A Muting Disable A 5.
设置为“锁定”后静音功能不能使用,图标显示: 设置为“解锁”后静音功能开启,图标显示: 静音必须在屏幕点亮的时候才能操控,按下任何按键使屏幕点亮, 再短按 按键切换静音模式。 21
6.背景灯光“点亮时间/关闭” 调节 6.1 使用 按键调到“背景灯”界面 H A Backlight 60S A 6.2 长按按键 进入“背景灯”设置界面 H A Backlight 60S A 6.3 使用 按键调节背景点亮的延迟时间,也可以关闭以省电 H A Backlight 00S A 6.
7. 恢复出厂设置 7.1 使用 按键调到“恢复出厂设置”界面 H Reset No A 7.2 长按按键 进入“恢复出厂设置”界面 H Reset No A 7.3 使用 A 按键选择是否恢复出厂设置 H Reset Yes A 7.4 短按 A A 按键确定,即可恢复出厂设置 H A Reset Resetting......
8. 固件版本号 8.1 使用 按键调到“版本号”界面查看本机固件的版本 H A Ve r s i o n 1.0.
接收器 屏显说明 A通道信号强度 B通道信号强度 A通道 B通道 Group A CH 41 A通道频道 A通道发射端电量 接收器电量 A通道接收端音频动态 Group B CH 11 B通道发射端电量 B通道频道 B通道接收端音频动态 当A/B通道打开时,图标背景颜色为黑色;当A/B通道关闭时,图标背景颜色是 透明的或无背景色。 25
操作说明 1.手动调节接收器A/B 通道的频道 1.1 长按按键 首先进入A通道‘CH’的设置界面,再次短按可 切换至B通道‘CH’的设置界面 Group A CH 41 1.2 使用 按键选择本机频道 Group A CH 45 1.
2.输出音频模式 “立体声/单声道”调节 2.1 使用 按键调到“输出模式”界面 Output Mode Mono 2.2 长按 按键进入“输出模式”设置界面 Output Mode Mono 2.
3.A/B通道功能设置 3.1 使用 按键调到“ A/B通道设置”界面 Setting Group A 3.2 长按 按键进入“ A/B通道设置”界面 Setting Group A 3.3 使用 按键选择要编辑的通道 Setting Group B 3.
4.A/B通道 “开/关”调节 4.1 使用 按键调到“通道设置-电源”界面 A B Group A Setting Power ON A B 4.2 长按 按键进入“通道设置-电源”设置界面 A B Group A Setting Power ON A B 4.3 使用 按键选择是否关闭通道 A B Group A Setting Power OFF A B 4.
5.A/B通道音量调节 5.1 使用 按键调到“通道音量设置”界面 Group A Setting Volume12 5.2 长按 按键进入“通道音量设置”界面 Group A Setting Volume12 5.3 使用 按键调整音量大小 Group A Setting Volume15 5.
6.A/B通道红外对码 6.1 使用 按键调到“通道同步设置”界面 Group A Setting Sync 6.2 长按 按键进入“通道同步设置”界面 Group A Setting Sync ? No 6.3 使用 按键选择是否同步,短按 Group A Setting Sync ? Yes 按键进行同步 Group A Setting Matching......
7.背景灯光“点亮时间/关闭” 调节 7.1 使用 按键调到“背景灯”界面 Backlight 60S 7.2 长按按键 进入“背景灯”设置界面 Backlight 60S 7.3 使用 按键调节背景点亮的延迟时间,也可以关闭以省电 Backlight 00S 7.
8.恢复出厂设置 8.1 使用 按键调到“恢复出厂设置”界面 Reset No 8.2 长按按键 进入“恢复出厂设置”界面 Reset No 8.3 短按 选择是否恢复出厂设置 Reset Yes 8.4 短按 按键确定,即可恢复出厂设置 Reset Resetting......
9. 固件版本号 9.1 使用 按键调到“版本号”界面查看本机固件的版本 Version 1.0.
技术规格 领夹发射器 TX 频道数 48 续航时间 6小时 天线 1/4波长导线天线 杂散辐射 <-60dBc 声音延迟 <20ms 音频失真 <0.5% 信噪比 >65dB 音频输入接口 3.5mm接口 电池 2节AA电池 外部供电 Micro USB 5V/1A 通道组 A / B 尺寸 107 x 66 x 26.
接收器 RX 36 频道数 48 续航时间 6小时 信噪比 >65dB 天线 1/4波长导线天线 接收灵敏度 -90dBm 声音延迟 <20ms 音频失真 <0.5% 频率响应 20Hz~18KHz 音频输出接口 3.5mm接口 电池 电池:2节AA电池 外部供电 Micro USB 5V/1A 尺寸 107 x 66 x 26.
Email: support@comica-audio.