Specifications

13
To connect your Cisco Unified IP Phone and Jabra
headset with the Jabra EHS Adapter, just follow
these simple steps:
SETTING UP THE CISCO UNIFIED IP PHONE
1. Connect the large plug to the AUX port on
the phone.
2. Connect the smaller plug to the AUX port on
the headset base.
3. Connect the normal audio cable to the
headset socket on the phone and the phone
socket on the headset base.
4. Ensure compatibility selector setting on
headset base is set to “B” and EHS setting
is set to DSHG. Set to CISCO on Jabra PRO
9400 Series and Jabra GO 6470 Series.
SETTING UP THE CISCO UNIFIED IP PHONE
9971, 9951/8961
1. Set Compatibility selector on headset base
to position “A” with DHSG on headset. Set
to CISCO on Jabra PRO 9400 Series and
Jabra GO 6470 Series.
2. Connect via USB to side port of phone
3. Connection should read: The Jabra LINK™
14201-30 is now connected.
4. Confirm by going to Setup>Accessories in
the phone. You should see the Jabra LINK™
14201-30 as a Device Type: Peripheral/
Device Class: Audio/Configured: Yes
Setting up Jabra PRO™ 9400 and
Jabra GO™ 6470 – follow the guide
on page 31.
SETTING UP JABRA PRO™ 920
1. Connect the Jabra LINK™ adapter as
shown in adapter documentation supplied
with the Jabra LINK™. On some phones
the telephone cable will also need to be
connected.
2. Call your connected desk phone using
another phone to enable the Jabra LINK™
adapter. Wait 10 seconds before answering.
3. Set a clear dial tone. Locate the clear dial
tone switch on the back of the Jabra PRO
920 base and rotate to “B”.
4. Set the Microphone volume. Make a call
to test your speaking volume. The listener
should not adjust their own volume. You
may adjust your microphone speaking
volume using the + / - volume buttons.
SETTING UP JABRA GN9350e
1. Open up the cover on the base unit.
2. On the LCD display, navigate to the handset
picture.
3. Navigate to the DHSG mode and select it by
pressing the OK button.
4. Set Compatibility selector in position “B” .
Compatibility selector
Jabra GN9350e
SETTING UP JABRA GN9330e
1. Place the headset in the base with its
indicators facing you.
2. Press the Telephone button
on the Base for 6 seconds
while the headset is in the
base until the headset’s blue
LED is flashing rapidly.
3. Use the volume up/down
button to shift between the
different EHS settings – see
table below.
The base unit’s 4 battery indicators show
which EHS mode the Jabra GN9330e is in.
25 %
100 %
GN RHL (Default)
DHSG
AEI
MSH
Note: If more than 15 seconds elapse without
pressing the volume + or volume – button, the
last selected interface will be activated.
4. Set the base unit to the DHSG mode.
5. To set the EHS mode, press the Telephone
button on the Base for 6 seconds until the
4 battery indicators flash once. Now wait 5
seconds and the headset is initialized.
6. Set Compatibility selector in position “B”.
SETTING UP JABRA GN9120 EHS/
JABRA GN9125
1. Set compatibility selector ( Telephone
Termination Switch Wheel ) in position “B”.
2. Set the base unit to the DHSG mode by
keeping the headset in the base and hold
the volume + / - buttons on the headset for
6 seconds until the red light on the base
flashes rapidly.
3. Scroll through the four different settings
using + / - and set to the lips icon. Leave for
15 seconds until the unit has displayed the
confirmation flash sequence and it is ready
to go!
SETTING UP JABRA GO™ 660
1. Turn headset on.
2. Press and hold answer/end button until
solid blue light comes on.
3. Activate Bluetooth on your phone.
4. Search for Bluetooth devices and select
Jabra EXTREME.
5. Press “OK” on the phone and confirm with
PIN code 0000 (4 zeros).
ELECTRONIC HOOK SWITCH (EHS) SOLUTIONS FOR CISCO
For more information and disclaimer, visit www.jabra.com/cisco
SET UP INFORMATION