Specifications

7
To connect your Alcatel-Lucent phone and
Jabra headset with the MSH 14201-09 cable,
just follow these simple steps:
Jabra headset base and Alcatel 8+9 Series.
Setting up Jabra PRO™ 9400 and
Jabra GO™ 6470 – follow the guide
on page 31.
SETTING UP JABRA PRO™ 920
1. Connect the Jabra LINK™ adapter as
shown in adapter documentation supplied
with the Jabra LINK™. On some phones
the telephone cable will also need to be
connected.
2. Call your connected desk phone using
another phone to enable the Jabra LINK™
adapter. Wait 10 seconds before answering.
3. Set a clear dial tone. Locate the clear dial
tone switch on the back of the Jabra PRO
920 base and rotate to “A”.
4. Set the Microphone volume. Make a call
to test your speaking volume. The listener
should not adjust their own volume. You
may adjust your microphone speaking
volume using the + / - volume buttons.
SETTING UP JABRA GN9350e
1. Open up the cover on the base unit.
2. On the LCD display, navigate to the handset
picture.
3. Navigate to the MSH mode and select it by
pressing the OK button.
4. Set Compatibility selector in position “A”.
SETTING UP JABRA GN9330e
1. Place the headset in the base with its
indicators facing you.
2. Press the Telephone
button on the Base for
6 seconds while the
headset is in the base
until the headset’s blue
LED is flashing rapidly.
3. Use the volume up/down
button to shift between
the different EHS settings – see table
below.
The base unit’s 4 battery indicators show
which EHS mode the Jabra GN9330e is in.
25 %
100 %
GN RHL (Default)
DHSG
AEI
MSH
Note: If more than 15 seconds elapse without
pressing the volume + or volume – button, the
last selected interface will be activated.
4. Set the base unit to the MSH mode.
5. To set the EHS mode, press the Telephone
button on the Base for 6 seconds until the
4 battery indicators flash once. Now wait 5
seconds and the headset is initialized.
6. Set Compatibility selector in position “A”.
SETTING UP JABRA GN9120 EHS/
JABRA GN9125
1. Set Compatibility selector ( Telephone
Termination Switch Wheel ) in position “A”.
2. Set the base unit to the MSH mode by
keeping the headset in the base and hold
the volume + / - buttons on the headset for
6 seconds until the red light on the base
flashes rapidly.
3. Scroll through the four different settings
using + / - and set to the lips icon. Leave for
15 seconds until the unit has displayed the
confirmation flash sequence and it is ready
to go!
TO INSTALL YOUR JABRA LINK™ 14201-20
EHS ADAPTER WITH YOUR ALCATEL PHONE
SETTINGS
1. Install your headset solution to your desk
phone according to the headset manual.
2. Set “Clear dial tone switch” in “A” position
– see headset manual.
3. Ensure your headset base unit EHS mode is
set up to DHSG - see headset manual*.
CONNECTIONS
4. With the cable included with your headset
system, connect the phone socket on your
headset base unit to the phone socket on
your Jabra LINK™ EHS Adapter.
5. With the cable marked white D, connect
the Headset / Handset socket on your Jabra
LINK™ EHS Adapter to the 3.5 mm headset
socket on the side of your desk phone.
6. With the cable marked orange A, connect
the COM socket on your Jabra LINK™ EHS
Adapter to the modular socket on your desk
phone marked with a “Bell” icon.
7. With the cable marked red, connect the AUX
socket on your headset base unit to the
Jabra LINK™ EHS Adapter AUX socket.
ALCATEL CABLES
EE4028
EE4038
EE4068
- Cable marked: D White
- Cable marked: Red
- Cable marked: A Orange
- Telephone cord
1
Note: The marked end of each cable must be con-
nected to the Jabra LINK™ EHS adapter.
USING DICTAPHONE OUTPUT
The dictaphone output can be used to record
a conversation in both directions. A 2.5 mm
jack to 3.5 mm jack cable is not included but
can be ordered as an accessory (Part Number
14201-21).
CLEANING THE JABRA LINK™ EHS ADAPTER
Only use a soft – and, if necessary, slightly
damp – cloth for cleaning the Jabra LINK™ EHS
Adapter. Do not use any solvents or cleansing
agents as these can damage the finish of the
Jabra LINK™ EHS Adapter.
1
Cable included in headset pack
ELECTRONIC HOOK SWITCH (EHS) SOLUTIONS FOR ALCATEL-LUCENT
For more information and disclaimer, visit www.jabra.com/alcatel
SET UP INFORMATION
Compatibility selector
Jabra GN9350e