TWO-WAY LCD AUTOMATIC TRANSMISSION REMOTE STARTER i CS-480 FM User Guide A note concerning the battery inside the transmitter: Depending on your usage of the transmitter, the battery can last anywhere between 3 to 6 months. When the battery is low, the transmitter will produce two beeps in a repetitive cycle. At that point you should replace your battery with a new one. That is why we recommend that you keep a spare battery somewhere handy such as the glove compartment. DOC:.1.
Table of Contents Introduction............................................. 2 Home Valet TM......................................... 6 Using the Transmitter ............................. 2 Ignition-Controlled Door Locks ............... 6 Remote-Starting Your Vehicle ................ 2 Ignition Re-lock....................................... 7 Vehicle Presets (Heater & Heated Seat) 2 Secure Lock............................................ 7 Driving Off...............................................
Windshield Wipers & Radio & Headlights Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become energized while running under remote start. When leaving the vehicle you must ensure that the windshield wiper and headlight switches are OFF. Leaving the headlight switch ON on certain types of vehicles could cause them to remain ON even after remote starter shut down, resulting in a dead battery.
Valet Mode Using the Valet Switch (if installed) When your vehicle is in valet mode, the remote starter functionalities are disabled. If the vehicle needs to be serviced, or if you park it indoors, the valet mode will prevent the engine from being remote-started accidentally. To put the system i n t o valet mode: 1. Turn the ignition key to the IGNITION ON (RUN) position. 2. Within 3 sec., press the valet button (the L.E.D. will come ON solid). 3.
The system will warn you if someone attempts to start your vehicle while it stands in home valet mode. The parking lights will: 1- Turn ON then OFF; then 2- Flash twice, pause; then 3- Flash twice again. Panic Mode In an emergency situation, you can activate panic mode by pressing and holding the FUNCTION button for 3 seconds.
Remote Door Locks If your remote starter was installed with the remote door locks option, you will have the convenience of remote keyless entry. See section Arming and Disarming the Remote Starter, on page 3, for further instructions on remote door locking and unlocking.
Ignition Re-lock On remote starters of this series, when ignition-controlled door locks are enabled and the ignition key is in the IGNITION ON (RUN) position, should any door be unlocked and opened, all doors will be relocked next time the brake pedal is pressed. Secure Lock Before it can remote-start your vehicle, the remote starter must first disarm the factory security system.
• The shape of the roof and A-pillars brings about considerable radio-frequency deflection (in this case the signal from the remote control). As a result, the direction in which the vehicle is facing in relation to the remote control can affect the range. Straight on – standing in front of the vehicle – generally gives you the greatest range; the second best performance is from the back. Using the remote control from either side of the vehicle will usually give the lowest range.
Basic Vehicle Operations Function Sound Instructions /description Lock Button pressed Icon 1 beep Lock and arm the starter kill Unlock 2 beeps Unlock and disarm the starter kill Trunk or aux 3 1 beep Trunk output Melody Start the engine Melody Stop the engine Start * (see runtime options below) + Stop None Back light On for 5 seconds Press once Transmitter Mode Selection Function Button pressed Power-saving mode +( + Press and hold Vibration mode Icon sound Melody ) and I
Time or Alarm Clock Adjustments User 1. Press and hold the FUNCTION button until a beep is heard 2. Upon hearing the beep, release the button, FUNCTION Transmitter The backlight will turn on the moment the FUNCTION button is pressed. ............................ is displayed ............................ is displayed ............................ is displayed 3. Press and hold the FUNCTION button once more 4. Release the heard, FUNCTION button when a beep is 5.
*Runtime Status (Indication purpose only) Function By pressing Icon Engine runtime Gasoline Diesel 4 minutes 9 minutes 15 minutes 20 minutes 25 minutes 30 minutes LCD Transmitter Operation and Confirmations (Second Car Control) Basic Operations Function Button press Lock Icon + Unlock + Stop Description 2 beeps + Start Sound 1 beep + + Melody None Melody Icon Sound Start/Stop While in Safe Start Mode Function Start on safe start mode Stop on safe start mode Button press +
Multi-Level Features (default state) Basic Features (press the FUNCTION button 1X) FUNCTION LOCK: ........................................................ aux 2 FUNCTION START/STOP ............................................... cold weather Multi-Car Operation (press the FUNCTION button 2X) FUNCTION FUNCTION LOCK:......................... 2nd car lock FUNCTION FUNCTION UNLOCK:..................... 2nd car unlock FUNCTION FUNCTION START/STOP: ............... 2nd car start/stop FUNCTION FUNCTION TRUNK: ....
Example: If the multi-level features were set to option 3, the setup would be as follows: Level 1 Customized feature Level 2 Multi car operation Level 3 Basic features The “Basic features” are now programmed as level 3 and therefore: To access the aux. 2 feature, the user needs to press on the FUNCTION button three (3) times followed by the LOCK button. To access cold weather mode, the user needs to press on the FUNCTION button three (3) times followed by the START/STOP button.
