JAN/07/2003 COMMANDO MODEL FM-870 REMOTE ENGINE STARTER WITH ALARM SYSTEM OWNER’S MANUAL RST872 1
JAN/07/2003 TABLE OF CONTENTS: A. REMOTE TRANSMITTER OPERATION ………………………………………….…………………….………. 4 B. BUTTON LOCK …………………………………………………..……………………………………….……..…. 4 C. LED DISPLAY .……………..………………………………………………………………………….……………. 5 D. CHIRP INDICATOR ..………..…………………………………………………………………………………..…. 5 E. PARKING LIGHT …….……..………………………………………………………………………………..….…. 5 F. ALARM OPERATION CONDITION .…………………………………………………………………………...…. 5 G. ACTIVE ARMING – ARM & LOCK .………………………………………………………………...…………….
JAN/07/2003 T. IGNITION CONTROL THE DOOR LOCK/UNLOCK. ………..………………….…………………………..…..9 U. TRUNK RELEASE (CHANNEL 3) OUTPUT ………..………………………………………………………..…10 V. CHANNEL 4 TIMER CONTROL OUTPUT ………..………………………………………………..…..……….10 W. CHANNEL 5 TIMER CONTROL OUTPUT ………..…………………………………………….….….……... 10 X. CHANNEL 6 TIMER CONTROL OUTPUT ………..…………………………………………….…….…….…. 10 Y. POWER ON MEMONRY: ………..………………………………………………………………….…….…..…. 10 REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE ………..………………………………………………………………….
JAN/07/2003 7. Should the unit malfunction, disconnect the fuse until the problem is corrected. 8. The use and operations of this system is the sole responsibility of the operator. 9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets. 10. Do not start the vehicle by remote while the standard transmission vehicle is parked at a steep place. OPERATION: A.
JAN/07/2003 LCD DISPLAY TRANSMITTER OPERATION ONLY: Transmitter Button - (C) - - System Function System’s Trigger Record Check Remark Press within 3 seconds System’s Status Check Press within 3 seconds Button Lock Press within 3 seconds and Hold Optional Driving Pager button for 2 seconds Press within 3 seconds Monitor Indoor Temperature Press within 3 seconds Daily Timer Start Press within 3 seconds LCD screen lamp turns on for 5 seconds.
JAN/07/2003 4. Passive Starter Disable 5. Panic 6. Car-Jacking 7. Car Locator Fast Flash Alarming Alarming 6 Chirps Flashes Flashes 12 Flashes Disable Flashes Disable Flashes Locking G. ACTIVE ARMING – LOCK & ARM: 1. Press button on the transmitter. 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle door will lock upon arming when interfaced with the security system.
JAN/07/2003 Shock Sensor Trigger Ignition Trigger Clear The Flash Icon: Press the button 3 times within 3 seconds will clear the flash icon on the LCD screen transmitter. TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times. PATHWAY ILLUMINATION (See Alarm Feature “II - 3” Programming): This feature turns the parking light “ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal.
JAN/07/2003 function and remote start function are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed either by using you remote transmitter, or by operating the Manual override sequence. Remote Door Lock Enter Valet Mode: Remote Door Unlock 1. From the disarmed condition, turn the ignition to “ON” position. 2. Push and hold valet switch for 2 seconds until the LED turns on.
JAN/07/2003 NOISE ABATEMENT CIRCUIT: You system has “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder, jackhammers airport noise, etc. Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor or switch is triggering the alarm. “Noise Abatement Circuit” will interpret this pattern of triggers as false alarm.
JAN/07/2003 Indoor Driving Paging Under the ignition switch “off” condition, press and hold the valet switch for 2 seconds to page the driver, one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD Transmitter and “ ” indication flashes on the LCD screen.
JAN/07/2003 REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE: When you want to start your vehicle, Activate Remote Start button twice on the transmitter. 1. Press 2. The parking light will activate to indicate the remote start received the signal. 3. The engine will start approximately 5 seconds. 4. Once the engine is running, after couple seconds the parking light will turn on again and climate controls will activate and adjust the vehicles interior temperature to your preset setting.
JAN/07/2003 2. Immediately depress the button once, within 2 seconds 3-a. 3 Hours Timer Start: Rapidly depresses the button. (or depresses + buttons, if you buttons = Start / Stop button.) The parking light will flash (3) times. The siren or horn program + chirps (3) times. The vehicle is now programmed to start every (3) hours. button first, within 3 seconds press 3-b. Daily Timer Start: Depress the transmitter button. The parking light will flash (6) times. The siren chirps (6) times.
JAN/07/2003 H. DISABLING THE REMOTE START SYSTEM: (If installed) This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the OFF position.
JAN/07/2003 A. BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery weakens a icon shall be displayed on the LCD screen. When the old battery is replaced to new one, there will be beep sounds indicate the power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons. Correct the time by pressing (See Timer Setting). for 3 seconds before using B.
JAN/07/2003 - (2-second) Enable / Disable Bi Sound (Bi) While Pressing Button 1. Screen Lamp ON: Press and hold the button one second, with one melody sound and the LCD screen lamp will turns on for 5 seconds 2. Power Save Mode: While the power save mode, the LCD remote transmitter uses “0” current to save the battery power. Entry: 1. Press & hold the button for 5 seconds, with one melody sound and icon on the LCD screen to indicate entry the “power save mode”. 2.
JAN/07/2003 Transmitter Button 1 Press & Hold the button for 3 seconds button once Press the 2 3 4 Description Timer Setting (Hour) *Flash digit for adjusting Press once. the button Press the button once Press the button once Press the button once Press the button once Press the button once Press & hold the for 2 seconds. EXIT: Press and hold the programming mode.
JAN/07/2003 7. Press the Press the button to start the count down timer, and the “ON” icon will show on the LCD screen. button to stop the count down timer, and the “OFF” icon will show on the LCD screen. 8. Press the button for 2 seconds with one-melody sound to confirm exit the timer program mode. Note: Maximum is 19 hours. 4. Time Set-Up For “Daily Timer Start”: Example to AM 6:30 1. Press & hold the adjusting. button for 3 seconds, with two-melody sound and the “Hours” digit flashes for 2.