Installation Guide

USE AND CARE GUIDE
COMMERCIAL ELECTRIC PREMIUM
LED RECESSED GIMBAL KIT
Safety Information
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m.- 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Warranty
Pre-Installation
PLANNING INSTALLATION
Compare all parts with the Package Contents list in this manual. If any part is missing or
damaged, do not install this product. Contact the Customer Service Team.
Installation
Model #
2003031702 WH
2003031602 DB
2003031802 BN
Fig. 1
Ceiling joist
Ceiling
Fig. 3.2
Top cover
NM Cable
or
BX Cable
NM Cable
strain relief
Junction
Box
Wire Terminal
Fig. 3.3
Wire Terminal
NM Cable
or
BX Cable
Junction
Box
Removable
strain relief
Top cover
NM Cable
Fig. 5
NM Cable
or
BX cable
Lower
springs
Upper
springs
Upper springs
Ceiling
Fig. 6
1.Choose the location for the fixture, taking into consideration the 5 in. depth clearance
requirement, the location of ceiling joists and the accessibility for the electrical supply.
Mark the selected location with a circle using the provided 3-1/4 in. diameter template.
2. Use a keyhole saw to cut a 3-1/4 in. diameter hole in the ceiling surface (Fig. 1).
3. Run non-metallic (NM) cable (also known as Romex) or an armored cable (also
known as BX) from your source power to the first hole, providing 6 in. (15.2 cm) to 8 in.
(20.3 cm) of slack extending below the hole (Fig. 2). Cable up to 12 AWG may be used .
4. Slightly loosen both Phillips head screws
on the junction box top cover. Slide the top
cover to the side, then rotate to open the
junction box (Fig. 3.1). Insert 5-6 in. of NM
cable into the junction box through one of the
strain relief slots (Fig. 3.2). If you are using a
BX cable, remove the black plastic NM cable
strain relief in order to secure the BX cable to
the junction box. If daisy-chaining to another
downlight, insert the next section of NM cable
or BX cable into the other strain-relief slot
(Fig. 3.3).
5. Remove at least 3 in. of the cable’s outer sheath and remove the plastic or paper
over-wrap. Strip approximately 3/8 in. of insulation from the ends of all supply wires.
Using the wire connectors, make the following wire connections within the junction box
(Fig. 3.2 and 3.3):
WHITE Fixture Wire to WHITE (NEUTRAL) Supply Wire
BLACK Fixture Wire to BLACK (HOT) Supply Wire
6. Carefully push the wires and the wire connections into the junction box. Close the
junction box cover. Tighten the fastening screws.
7. Adjust light color settings to the desired levels (Fig. 4).
Light Color Settings:
The light color settings adjust the color temperature (K) of the LEDs from 2700K
(warm white) all the way to 5000K (daylight). Application type and personal preference
usually dictate the color temperature needed. Most residential applications utilize
2700K or 3000K- more of a yellowish hue. Commercial offices and outdoor settings
typically use 4000K or 5000K- more of a bluish hue. While most consumers will
choose the factory setting of 2700K, it is mostly personal preference.
9. Flip up the spring clips against the junction box and insert the fixture into the ceiling
hole, junction box first. The longer upper springs go up through the ceiling hole. The
smaller lower springs stay below the ceiling. Place your fingers between the ceiling
and the lower springs to prevent them from marking the ceiling surface when installing
(Fig 5).
10. Continue inserting the fixture into the hole until the upper springs are engaged
above the ceiling and the fixture trim is flush against the ceiling (Fig. 6).
11. To adjust the direction of the light, pull out the gimbal head and twist to desired
direction (Fig. 7). The gimbal can be rotated to 40 degrees vertically and 350 degrees
horizontally. Use the indentation shown below to assist in pulling the gimbal head out
of the housing (Fig. 8).
Dimming
Dimming performance may depend on the dimmer, the dimmer range adjustment
setting (for dimmers with brightness range adjustments), the wiring method, and/or the
number of LED modules installed onto the dimmer circuit.
● For dimmer selection, it is recommended to use one of the following dimmers:
Five-year Limited Warranty
Commercial Electric warrants this product to be free from defects in materials and
workmanship for five years from the original date of purchase by the consumer. This
warranty is limited to the counter replacement at the time of purchase, with the original
purchase receipt. Commercial Electric will not be liable for the loss or damage of any
kind, incidental or consequential damages of any kind, whether based on warranty
contract or negligence, and arising in connection with the sale, use or repair of the
product claimed to be defective. Some states do not allow the exclusion or limitation of
incidental or consequential damages so the above limitation may not apply to you. This
warranty gives you specific legal rights and you may also have other rights, which vary
from state to state. Misuse, accident, improper installation or maintenance will also
void the warranty.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation. This equipment, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. Any
changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures: reorient or relocate the receiving antenna; increase the separation
between the equipment and receiver; connect the equipment into an outlet on a circuit
different from that to which the receiver is connected; consult the dealer or an
experienced radio/TV technician for help.
For product questions or feedback, contact the Customer Service Team at
1-877-527-0313 or visit www.HomeDepot.com.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
PACKAGE CONTENTS
TOOLS REQUIRED
1. Hand saw
2. Screwdriver
SPECIFICATIONS
3 in. Premium Gimbal Kit
THANK YOU
enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Commercial Electric!
We appreciate the trust and confidence you have placed in Commercial Electric
through the purchase of this LED Gimbal Kit.
We strive to continually create quality products designed to
Fig. 7
40Deg
350Deg
Fig. 8
Fig. 2
Ceiling
NM Cable or BX Cable
Hole
8. Raise the Premium Kit up to the ceiling hole, while simultaneously pushing the
excess NM cable or BX cable into the ceiling (Fig. 5).
Power(W) 10.5W
Finish White / Dark Bronze / Brushed Nickel
2700K/3000K/3500K/4000K/5000K
650lm
CCT(K) 5-Step Select
Lumen(lm)
Product Model
3 in. Premium Gimbal Kits
3-1/4 in.
Cut Out Diameter
FCC responsible party name: Dangoo Electronics (USA) Co., LTD
Address: 2494 Sand Hill Road
Bldg 7, Suite 100
Menlo Park, CA 94025
United States
650-422-3572
ytitnauQnoitpircseDtraP
Wire Connectors
3A
Ceiling cutout template
1C
LED Gimbal Kit
1B
WARNING – Risk of fire or electric shock. Lighting installation requires
knowledge of electrical systems. If not qualified, do not attempt installation.
Contact a qualified electrician.
WARNING – Risk of fire or electric shock. Disconnect power at fuse or circuit
breaker before installing or servicing.
WARNING – This fixture is an IC type fixture. Some insulation types that
meet this requirement are blanket batting/roll and blown-in loose fill. Do
not install in a ceiling with spray foam type insulation. Any part of the
fixture may come in direct contact with combustible material, such as a ceiling
joist or floor board.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to
edges of sheet metal or other sharp objects.
WARNING – Min. temperature rating of -20°C.
WARNING – This fixture may be installed over a wet or damp location such as
a shower stall or bathtub enclosure. The area above the ceiling surface must,
however, be a dry location.
WARNING – This fixture is designed for ceiling surfaces that are 1-1/4 in. thick or
less. Do not use this fixture on ceiling surfaces that are thicker than 1-1/4 in.
WARNING – This fixture requires an existing ceiling surface, such as drywall,
for installation. To install this fixture, a hole needs to be made into the ceiling
surface at the desired location. Then, power supply wiring (NM cable) needs to
be installed from the power source to the hole.
WARNING – Do not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation.
Note: Be sure not to make the hole any larger than specified. An oversized
hole may not allow for proper installation.
Note: This fixture does not require a ground wire. Secure supply ground wire
end(s) together with a wire connector.
5000K-Daylight
4000K-Bright White
3500K-Neutral White
3000K-Soft White
2700K-Warm White
Fig. 4
Light Color
Daylight
Warm
White
5000K
4000K
3500K
3000K
2700K
Average beam angle: 45.8°
Light Distribution
0
200
400
600
800
1000
180.0°
150.0°
120.0°
90.0°
60.0°
30.0°
0.0°
30.0°
60.0°
90.0°
120.0°
150.0°
0-180
90-270
Fig. 3.1
Junction box top cover
No. Brand Dimmer Family Model
1 Lutron Skylark CTCL-153PDH-WH
2 Leviton Sure Slide R62-06674-P0W
4 Eaton Sky AL SAL06P-LA-K
5 Lutron Caseta P-PKG1W-WH-R
6 Lutron Maestro MACL-153MH-WH
7 Lutron Diva DVCL-153PR-WH
8 Eaton AL Series AAL06-C1
9 Leviton Decora R12-06672-1LW
10 Leviton IllumaTech R50-1PL06-10M
11 Lutron Toggler TGCL-153PH-WH
3 Lutron Diva DVELV-303P
WARNING – Use cables having wires rated 90˚C or more.