Installation Guide
LED Aimable Shop Light
Installation Instructions
WARNING: Carefully read and
understand the information given in this
manual before beginning the assembly
and installation. Failure to do so could
lead to electric shock, re, or other
injuries which could be hazardous or
even fatal.
WARNING:
1. The unit is intended to be installed
directly beneath a ceiling-mounted
receptacle
2. Do not install on radiant-heating type
ceiling.
3. Voltage and current rating of shop
light: 120VAC 0.4A 42W 60Hz
4. Maximum 8 units to be interconnect-
ed.
5. The maximum distance to the
receptacle is determined by the 1.5M
length of cord provided.
6. The terminal of the last xture needs
to be closed by the end cap. Live parts
cannot touch hands.
WARNING: Ensure the electricity to
the wires you are working on is shut off.
Either remove the fuse or turn off the
circuit breaker.
WARNING: Changes or modications
not expressly approved by the party
responsible for compliance could void
the user’s authority to operate the
equipment.
NOTICE: Added weight of the device
may cause instability of a free-standing
portable luminaire. This device is not
intended for use with emergency exits.
WARNING: This equipment has been
tested and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
■ Reorient or relocate the receiving
antenna
■ Increase the separation between the
equipment and the receiver.
■ Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
■ Consult the dealer or an experienced
radio/TV technician for help.
Safety Information
Warranty
This product is warranted to be free from defects in workmanship and materials for up to 5 years from
date of purchase。
INSTALLATION FIGURES
PACKAGE CONTENTS
Part Descripon Quanty
A
42”Shoplight
1
B 5FT Plug-in Power Cord 1
C 5FT Linking Cord 1
D End-to-End Row connector 1
E Mounng Screws 2
F Flush Mounng Rubber Gaskets 2
G
Drywall Anchors
2
H Suspension Cables 2
I Pull Chain Extension 1
J
S-hooks for use with user-supplied
suspension cables/chains longer than 36”
2
Note: TURN OFF POWER AT CIRCUIT BREAKER BOX!
WIRING AND FIXTURE OPERATION CAUTION:
Connect xture to supply wires rated for at least 90°C (194°F)
Assistance may be required to support xture during installation.
INSTALLATION OPTIONS
Remove xture from the carton and check for any shipping damage.
HANGING CABLE INSTALLATION
1. a) Installing to a wooden joist (preferred):
Drill 1/16” pilot holes in the ceiling/joists 31 29/32” apart. See Fig. 1.
b) Installing to drywall with no wooden joist:
Drill 7/32” pilot holes in the ceiling 31 29/32” apart. Insert drywall anchors (G) into pilot holes.
See Fig. 1.
2. Unscrew the top caps of the mounting cables (H) and insert the mounting screws (E) through the top
caps. Insert the mounting screws into the pilot holes in the ceiling with a Phillips head screw driver.
See Fig. 2.
3. Install the suspension cables (H) back into the top cap that are now on the ceiling. See g. 3.
Fig. 1
Fig. 2
Fig. 3