Installation Guide

ManualsBrandsCommercial Electric ManualsFlush Mount Ceiling Lights32 in. Low Profile Oval Brushed Nickel LED Flush Mount Ceiling Light with Night Light Feature Adjustable CCT

Item # 1000000000/1000000000

1000000000/1000000000

Model # 56587111/56587112

56587113/56588111

HARDWARE INCLUDED

Part Description Quantity

AA Drywall Anchor 6

BB Safety Cable 2

CC Mounting Screw 6

DD Wire Connector 3

EE Pins 4

FF Location Paper 1

GG Lever 1

USE AND CARE GUIDE

32 IN. FLUSHMOUNT WITH NIGHT LIGHT

AA BB

NOTE: Keep your receipt and these instructions for proof of purchase.

WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the

fuse or turn off the circuit breaker before removing an existing light ﬁxture or installing the new one.

If you are unfamiliar with electrical installations, we recommend you contact a qualiﬁed electrician to do the installation.

INSTALLATION

NOTE: Select a suitable location that can support the weight of the ﬁxture. Determine the method for mounting the ﬁxture

before drilling, based on the type of ceiling.

NOTE: Two people are recommended for the installation of this light ﬁxture.

1. Refer to the arrow position of ﬁxture plate (A) and using the lever (GG) to remove the external frame (B).

PACKAGE CONTENTS

Part Description Quantity

Fixture Plate 1

B External Frame 1

2. Using pins (EE) to ﬁx the location paper (FF) on the installation surface where you desired, mark the 6 holes position by

pencil. Remove the paper, drill 6 holes using Φ6mm driller, insert the drywall anchors (AA).

NOTE: Do not need drill hole on wooden surface.

Φ6mm

location paper

FF GG

Summary of content (8 pages)

PAGE 1
Item # 1000000000/1000000000 1000000000/1000000000 Model # 56587111/56587112 56587113/56588111 Use and Care Guide 32 in.
PAGE 2
INSTALLATION (continued) 3. Fix the two safety cable (BB) by mounting screws (CC) on the middle holes of surface , then, hook with the fixture base (A) through the hole on the middle. AA CC BB A 4. Connect the hot and neutral wires from the J-box into the wire connectors (DD) of the black and white wires from the fixture base (A). Insert the ground wire from the J-box into the wire connector (DD) of the green wire from the fixture base (A). Make sure to fasten them well. DD A 5.
PAGE 3
SELECTING MAIN LIGHT OR NIGHTLIGHT MODE The product can be used in one of two modes: Main light mode, which provides full brightness and allows selection from three color temperatures, or nightlight mode. Nighlight mode provides reduced light output at 2000K color temperature for very soft illumination at night. TO TURN ON THE MAIN LIGHT 1. Turn on the light switch to activate the light fixture. TO CHANGE TO NIGHTLIGHT MODE WITH REDUCED LIGHT OUTPUT 1.
PAGE 4
Troubleshooting Minor problems often can be fixed without the help of an electrician. WARNING: Before doing any work on the fixture, disconnect power to the light fixture. Problem The fixture will not light. The fuse blows or the circuit breaker trips when the light is turned on. The light fixture flickers or makes a buzzing sound. Out of sync Possible Cause The power is off. Solution Ensure the power supply is on. The circuit breaker is off. Ensure the circuit breaker is in the on position.
PAGE 5
Artículo # 1000000000/1000000000 1000000000/1000000000 Modelo # 56587111/56587112 56587113/56588111 MANUAL DE USO Y CUIDADO LÁMPARA EMPOTRADA DE 32 PULG.
PAGE 6
instalación (continuación) 3. Fije los dos cables de seguridad (BB) mediante tornillos de montaje (CC) en los orificios centrales de la superficie, luego enganche con la base de la lámpara (A) a través del orificio en el medio. AA CC BB A 4. Conecte los cables vivo y neutro de la caja de conexiones en los conectores de cables (DD) de los cables negro y blanco de la base (A). Inserte el cable de tierra de la caja de conexiones en el conector de cables (DD) del cable verde de la base de la lámpara (A).
PAGE 7
SELECCIONAR EL MODO DE LUZ PRINCIPAL O LUZ NOCTURNA El producto se puede usar en uno de dos modos: Modo de luz principal, que proporciona un brillo total y permite la selección de tres temperaturas de color, o modo de luz nocturna. El modo de luz nocturna proporciona una potencia luminosa reducida a 2000K para una iluminación muy suave durante la noche. encender LA LUZ principal 1. Encienda el interruptor para activar la lámpara. cambiar al modo de luz nocturna con pote ncia luminosa reducida 1.
PAGE 8
Solución de problemas Los problemas menores se pueden arreglar generalmente sin la ayuda de un electricista. ADVERTENCIA: Antes de realizar cualquier trabajo en la lámpara, desconecte la electricidad que la alimenta. Problem La lámpara no enciende. El fusible se quema o el disyuntor se abre cuando se enciende la lámpara. La lámpara parpadea o emite un zumbido. Fuera de sincronización Possible Cause El suministro eléctrico está cortado. Solution Asegúrese de que el suministro eléctrico esté activado.