Item #0000 000 000 Model # C423100 USE AND CARE GUIDE 12 IN. MULTI-COLOR LED STRIP KIT (4-PACK) +12V +12V R R G B W G B W B W B W R G G R +12V +12V R G B W WW R G Flash B W B +12V +12V G +12V R G B W R G R ON B W OFF +12V Strobe Fade Smooth Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-877-527-0313 HOMEDEPOT.
Table of Contents Table of Contents........................................................2 Safety Information......................................................2 Warranty.....................................................................3 What is covered......................................................3 What is not covered................................................3 Pre-Installation...........................................................3 Planning Installation............................
Warranty THREE (3) YEAR WARRANTY WHAT IS COVERED The manufacturer warrants this fixture to be free from defects in materials and workmanship for a period of three (3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service.
PACKAGE CONTENTS A +12V +12V R R G G B B W W +12V +12V B R R G G B B W W +12V +12V R R G G B B W W +12V +12V R R G G B B W W C R G OFF ON B WW Flash Strobe Fade D Smooth E F Part Description Quantity A Adapter 1 B 12 in.
Installation 1 Installation considerations □ □ □ What is the best layout configuration for your installation? How will you run and conceal the wires to your LED tape lighting? Temporarily mounting the LED light strip using painter’s tape allows you to experiment with tape light positioning before permanent installation. IMPORTANT: Using painter’s tape or masking tape, temporarily place the LED light strip into your desired mounting position.
Installation (continued) 3 Cutting the LED strip (optional) □ By cutting the strip and exposing the copper pads, optional connector (C760011) or accessory (C760110) pack can be used for a more custom installation.
Installation (continued) 5 Installing the LED strip □ 4A Tape method: Working from one end to the other, remove the 3M paper backing and press into place. Press between the LEDs to help ensure secure contact with the mounting surface. Avoid pressing on the individual LEDs as this could damage the LED solder connections. □ 4B Clip and screw method: Place the LED strip in the desired position. Use the clips and screws to secure the LED strip as shown. Clips should be placed in open areas of the strip.
Installation (continued) 6 Installing the infrared receiver There are two options: A. Remove the protective tape from the adhesive back of infrared receiver, then place the infrared receiver onto the position and press to insure proper adhesion to the surface. B. Use the two screws to install the infrared receiver onto the position.
Installation (continued) 7 Connecting to the power supply Connect adapter to power outlet Connect the adapter plug to infrared receiver controller Infrared receiver controller Adapter with plug LED strip light Infrared receiver 9 HOMEDEPOT.com Please contact 1-877-527-0313 for further assistance.
Operation 1 Using the remote □ Direct the remote (D) towards the infrared receiver (C) to change RGBW colors of the strip. A B A--- Use to increase or decrease color brightness and to slow down or accelerate speed. R G OFF ON B WW C D E F G Flash Strobe Fade Smooth (NOTE: there are 10 light intensity options and 10 speed setting options) B--- ON/OFF switch. C--- R,G,B,W: Choose color: red, green, blue or warm white. D--- Flash key: 7 color jump change. E--- Strobe key: Strobe color effect.
Care and Cleaning □ To clean the fixture, disconnect the power by unplugging the adapter. Use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture. □ Do not use any cleaners with chemicals, harsh abrasives, or solvents. Use only a dry soft cloth to dust or wipe carefully. Troubleshooting Problem Possible Cause Solution The LED will not light. The LED is burned out. Discontinue use of the lamp. The power is off. Ensure the power supply is turned on.
Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-877-527-0313 HOMEDEPOT.COM Retain this manual for future use.