Instructions / Assembly

5 in. – 7 in.
6 in.
FIG. 2
FIG. 3
PARTS
SOCKET ADAPTER
ASSEMBLY
RETROFIT TRIM
COMPATIBLE HOUSING
DIMENSIONS
FIG. 4
FIG. 5
OR
WARNING - RISK OF ELECTRIC SHOCK.
DISCONNECT MAIN POWER AT FUSE OR CIRCUIT
BREAKER BEFORE INSTALLING OR SERVICING
THE FIXTURE.
QUESTIONS? CALL TOLL
FREE 1-800-345-0542
Please read carefully and save these instructions, as
you may need them at a later date.
GENERAL: All electrical connections must be in accordance with local
and National Electrical Code (N.E.C.) standards. If you are unfamiliar with
proper electrical wiring connections obtain the services of a qualified
electrician.
Remove the trim from the box and make sure that no parts are missing by
referencing the PARTS illustrations.
THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A
LED LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY CSA OR CANADIAN AUTHORITIES
HAVING JURISDICTION.
__________________________________________
WARNING- RISK OF FIRE OR ELECTRIC SHOCK
FOR USE WITH HOUSING MODELS: INCANDESCENT HOUSINGS –
COMMERCIAL ELCETRIC C7IC, C7ICR, C7ICA, C7ICRA, C7, C7R,
C7S, HBR5000SIC; HALO H7ICT, H7RICT, H7ICAT, H7RICAT, H7T,
H7RT, H27ICT, H27T, H27RT, H750ICAT, H750RICAT; CORDELIA
HBR7LICAT, HBR7LICRAT; CAPRI CR1, CRR1; ELCO EL7ICA,
EL7RICA; JUNO IC22, IC22R; LITHONIA L7X, L7XR; THOMAS PS1,
PS1-RM; DMF DH6ICATQ, DH6ICRATQ; NORA NHIC-17QAT, NHRIC-
17QAT; ELITE B6IC, B6RIC; SEA GULL 11018, 11028. HALO LED
HOUSINGS – H750ICAT, H750RICAT.
• Do not alter, relocate, or remove wiring, lampholders, power supply, or
any other electrical component. Installation of the retrofit assembly
requires a person familiar with the construction and operation of the
luminaire’s electrical system and the hazard involved. If not qualified,
do not attempt installation. Contact a qualified electrician.
• Do not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation.
• To prevent wiring damage or abrasion, do not expose wiring to edges
of sheet metal or other sharp objects.
____________________________
ASSEMBLY AND INSTALLATION
1. If the installed housing does not have TORSION SPRING SLOTS or
C-CLIPS (FIG. 3), then remove the SCREWS securing the TORSION
SPRINGS to the HEATSINK. Attach the FRICTION BLADES (included)
to the same location using the SCREWS that were previously removed.
(FIG. 6)
INCANDESCENT HOUSINGS
1. Unscrew the WING NUT inside the CAN to detach the SOCKET
BRACKET from the CAN. Disengage the SOCKET from the SOCKET
BRACKET. (FIG. 2)
2. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 3)
3. Attach the GROUND WIRE to the CAN using the provided self-tapping
GROUND SCREW and star washer. Make sure that the GROUND
SCREW does not interfere with the entry of the RETROFIT TRIM into
the HOUSING.
4. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the
MALE CONNECTOR of the SOCKET ADAPTER ASSEMBLY. (FIG. 4)
5. If using TORSION SPRINGS, squeeze both TORSION SPRING arms
together and insert into the TORSION SPRING SLOTS (or RECEIVER
BRACKETS) of the CAN. (FIG. 5)
6. Tuck all wires into the CAN and carefully push the RETROFIT TRIM
into CAN. (NOTE: To provide enough room in shallow cans, carefully
position SOCKET ADAPTER and SOCKET adjacent to the long side of
the LED DRIVER prior to inserting the RETROFIT TRIM into the CAN.)
(FIG. 5)
LED HOUSINGS
1. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the
MALE CONNECTOR of the HALO HOUSING. (FIG. 4)
2. If using TORSION SPRINGS, squeeze both TORSION SPRING arms
together and insert into the TORSION SPRING SLOTS (or RECEIVER
BRACKETS) of the CAN. (FIG. 5)
3. Tuck all wires into the CAN and carefully push the RETROFIT TRIM
into CAN. (NOTE: To provide enough room in shallow cans, carefully
position SOCKET ADAPTER and SOCKET adjacent to the long side of
the LED DRIVER prior to inserting the RETROFIT TRIM into the CAN.)
(FIG. 5)
LED 6” RETROFIT TRIM INSTALLATION
INSTRUCTIONS - MODEL CER6742A
FIG. 6
REV 05-AUG-14
ALL RIGHTS RESERVED  COMMERCIAL ELECTRIC 2014