Instructions / Assembly

ManualsBrandsCommercial Electric ManualsOtherSteel Plate 2-Lamp Hanging Fluorescent Silver ShopLight

Be sure to install the ceiling hooks no more than fixture length apart. Install the

fixture to the ceiling by looping the remaining ends of each SUPPORT CHAIN (3)

to each ceiling-installed hook.

3. To install the tube lamps, guide the pins on one end of the lamp into one socket

(4). Guide the other end of the tube into the opposite socket (4). Rotate the tube

90° (1/4 turn) in either direction until seated. Be sure to use the correct type and

wattage lamps, which are specified on the provided label on the fixture.

4. Plug the fixture’s power cord to a 120 V – 60 Hz outlet.

5. Pull the HANGING SWITCH CHAIN to turn the fixture on or off.

Fig. 1

___________________________

ASSEMBLY AND INSTALLATION

1. Attach the small loop of each “S”

HOOK (2) to the end of each

SUPPORT CHAIN (3). Feed the

large loop of each “S” HOOK (2)

through the holes provided at each

end of the CHANNEL (1). Close

both ends of each “S” HOOK (2)

using pliers. (Fig. 1)

2. Select the desired installation

location. Be sure that a standard

120 V – 60 Hz outlet is located within

reach of the fixture’s power cord.

Install two hooks (not included) on

the desired location of the ceiling.

STEEL PLATE 2-LIGHT 4-FT

SHOPLIGHT MODEL CESL403-CL

INSTALLATION INSTRUCTIONS

Please read carefully and save these instructions. Failure to do so may lead to

electrical shock or fire, which may cause injury or death.

_______

CAUTION

WARNING – RISK OF FIRE: Turn off the main power at the circuit breaker before

installing the fixture, changing lamps, or performing other maintenance in order to

prevent possible shock.

________

GENERAL

All electrical connections must be in accordance with local, and national electrical

codes.

Prior to installation it is important to follow the following guidelines:

A. Be sure the insulation power cord has not been damaged during

installation and that there are no rough or sharp edges in contact with

the wires.

B. Use only the type of light bulb specified, with wattage not greater than

specified on the wattage label found on the fixture.

C. Remove all protective plastic film covering from the fixture.

D. Do not mount the fixture vertically or flush against the ceiling.

Tools needed for installation: Phillips screwdriver, pliers.

_____________________

This product is ENERGY STAR® listed. The ballast can be replaced without having to

cut wires. Please contact a qualified electrician if ballast replacement is needed.

Tools needed for ballast replacement:

Flathead screwdriver, Phillips screwdriver,

hex head screwdriver, small paper clip

Unscrew the fastener holding the ballast to the fixture. Insert an unbent paper clip into

the same hole the ballast wire is entering the lamp socket and pull the wire out.

Fig. 3

Summary of content (3 pages)

PAGE 1
___________________________ ASSEMBLY AND INSTALLATION 1. STEEL PLATE 2-LIGHT 4-FT SHOPLIGHT MODEL CESL403-CL 2. INSTALLATION INSTRUCTIONS Please read carefully and save these instructions. Failure to do so may lead to electrical shock or fire, which may cause injury or death. Attach the small loop of each “S” HOOK (2) to the end of each 3 SUPPORT CHAIN (3). Feed the large loop of each “S” HOOK (2) through the holes provided at each end of the CHANNEL (1).
PAGE 2
______________________ MONTAJE E INSTALACIÓN 1. Coloque el bucle pequeño de cada GANCHO "S" (2) al final de cada CADENA DE SOPORTE (3). Inserte el bucle grande de cada GANCHO "S" (2) a través de los agujeros provistos en cada extremo del CANAL (1). Cierre ambos extremos de cada GANCHO "S" (2) con unos alicates. (Fig. 1) 2. Seleccione el lugar de instalación deseado. Asegúrese de que un enchufe Fig. 1 estándar de 120 V - 60 Hz este al alcance del cable de alimentación del aparato.
PAGE 3
___________________________ ASSEMBLAGE ET INSTALLATION Enfiler les petites boucles de crochets en S (2) à une extrémité de chaque chaîne de support (3). Enfiler les grands boucles de crochets en S (2) à travers les trous prévus dans le boîtier (1). Femer les deux extrémités de chaque crochet en S (2) à l’aide d’une pince. (Fig. 1) 2. Choisir un emplacement pour Fig. 1 l’installation. S’assurer qu’une prise secteur standard 120 V/60 Hz se trouve à portée du cordon d’alimentation en la lampe.