Instructions / Assembly
Installation
Installation
Part Description
Fixture body
B
A
TOOLS REQUIRED
Hardware not shown to actual size.
HARDWARE INCLUDED
3
Installing the mounting bracket assembly
Installing the xture to the mounting
arm (optional)
2
Drilling the mounting hole
4
Making the electrical connections
Safety Information
PACKAGE CONTENTS
Pre-Installation
Pre-Installation
Quantity
1
1
NOTE:
Make sure the power is off.
Using the wire hole of the junction box as
center, mark and drill the three mounting
holes on the surface of the desired locations
□
□
Pull the supply wires down out of the mounting
surface.
Pull the supply wires through to the knockout on the
cover plate.
□
First install the two mounting screws (BB) on the bottom of
the
mounting bracket assembly (C) and leave about 3/8 in.
space under the head, and then install the third screw on
the top of the mounting bracket assembly (C). Last tighten
the two bottom screws (BB) to secure the xture.
□
□
□
□
Ladder Gloves
Safety
goggles
Electrical
tape
Wirestripper
Measuring
tape
B
D
DD
D
D
CC
Wrap waterproof electrical tape (not included) around
the wire connectors (AA), and ensure they are secure.
Push all excess wire and wire connections back
□
□
□
Read all instructions prior to beginning the
installation process.
Make sure the power is turned off at the
electrical panel box before beginning your
installation. Turning the power off at the wall
shock.
IMPORTANT SAFETY INSTRUCTIONS
(Save These Instructions)
CAUTION:
Keep the lamp away from
materials that may burn.
WARNING: This lighting is suitable for wet
locations.
Care and Cleaning
□
removing the fuse at the fuse box.
□
□
CAUTION: Do not use chemical solvents or harsh abrasives to clean the xture or components, as
damagemay occur.
Use a dry or slightly dampened, clean cloth (use clean water, never use a solvent) to wipe the
□
All electrical connections must be in accordance
with local codes and the National Electrical Code.
If you are unfamiliar with methods of installing
licensed electrician.
AA
Mounting screws
x 3
BB
Wire connectors
x 3
Mounting bracket assembly
CAUTION:
The LEDs in this product
are not replaceable.
C
BB
negative wires from the supply circuit, the positive wires
supply circuit, and the ground wire (green) from the
the wire connectors (AA).
5
Reinstalling the cover plate
□
6
□
outer diameter of 1-5/8 in. (42 mm) (not included)
You can install this xture to a mounting arm with an
using the same installation methods.
Remove the knockout on the back of the cover
plate for junction box/arm mounting or remove
the knockout on the bottom of the cover plate
for conduit mounting and feed the power supply
wired through the hole.
□
□
□
□
□
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Fixture arm
C
1
Installation
C
Cover plate
Cover plate
Mounting arm
Cover plate
Knockout
C
B
B
1
Removing the cover plate
□
□
Loosen the set screws and separate the cover
plate from the xture arm (B) and set aside for
reassembly.
A
Adjustable
wrench
Electric
drill
1/4 in.
Drill bit
Pencil
10 (3/8")
the previously-removed set screws.
NOTE:
conduit connectors, conduits and junction
box that are UL listed suitable for wet
locations and are properly installed and
grounded.
AA
B
Waterproof electrical tape
compliance could void the user’s authority to operate the equipment.
Waterproof silicon
Mounting surface
Canopy
7
□
between the canopy and mounting surface,
waterproof silicon, caulk or gel should be applied to
seal any gaps around the junction point.
WARNING: Keep the photocell covered until
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio ortelevision reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
installation is complete.
8
□
□
To disable the dusk-to-dawn photocell (D), keep the photocell cap (DD)
over the dusk-to-dawn photocell (D). This will prevent the dusk-to-dawn
photocell (D) from controlling the ON/OFF function, and will allow the
ON/OFF function to be directly controlled by the wall switch.
WARNING: Keep the photocell cap until
installation is complete.
Troubleshooting
Problem Possible Cause Solution
The power is off.
Make sure the power supply is on.
There is a faulty wire
connection.
There is a faulty switch. Test or replace the switch.
The light will not
illuminate.
Light cycles or
The light does not
automatically turn off
during daylight hours.
The photocell is covered.
The photocell is detecting
light nearby.
to keep their light don’t interfere the
photocell.
The Dusk to Dawn feature
was bypassed.
Follow the operation steps and Reinstate
the Dusk to Dawn feature.
The photocell is in a dark
or shaded area.
Make the photocell get the direct sunlight.
Remove the cover on the photocell or
Clean the photosensor.
Check the wiring. Contact a qualied and
licensed electrician if you are not comfortable
troubleshooting wiring problems.
CAUTION:
Do not connect this light xture
to a dimmer switch.
Operation
Photocell
Photocell cap
D
1
54 [2.1"]
35 [1.4"]
70 [2.8"]
Checking the ON/OFF function of the light
To activate the dusk-to-dawn photocell (D), remove the photocell cap (DD)
from the photocell (D) and make sure it is installed in direct view of sunlight.
x 1
x 1
CC
DD
Photocell sleeve
Optional: Installing the photocell sleeve
9
□
If the light cycles or flashes on and off, then place the
photocell sleeve (CC) to cover the photocell (D) of fixture.
Warranty
3-YEAR LIMITED WARRANTY
THANK YOU
We appreciate the trust and condence you have placed in Commercial Electric through the purchase of this LED light
xture. We strive to continually create quality products designed to enhance your home. Visit us online to see our
full line of products available for your home improvement needs. Thank you for choosing Commercial Electric!
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
Questions, problems, missing parts? Before returning to store,
HOMEDEPOT.COM
Contact the Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.
call Commerial Electric Customer Service
Retain this manual for future use.
USE AND CARE GUIDE
LED LIGHT FIXTURE
Item
#1003934461
Model #DW10279AZ8-C
Waterproong the xture (optional)
NOTE:
a.
When installing during the day, take out the photocell cap/sticker (DD) from the
accessory bag to cover the photocell. The light should turn on after a slight
delay. Please made sure to remove the photocell cap/sticker (DD) after the light
can work normally, otherwise the light does not shut off during the daytime.
b.
If the light does not shut off during the daytime, please shine the photocell
with the ashlight for 2-3 minutes, the light will turn off after two minutes, this
means that the photocell did not receive enough illuminate, please re-move the
light so that the photocell can receive the illuminate.
Compatible with mounting arm #1003050122
(sold separately).
□
The xture contains a photocell with Dusk to Dawn feature,that automatically turns the lights on at
dusk and off at dawn.
□
□
The manufacturer warrants this lighting xture against defects in materials and workmanship for a period
of three years from the date of purchase. If within this period the product is found to be defective in material
or workmanship, the product must be returned, with a copy of the bill of sale as proof of purchase, to the
original place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase
price to the original purchaser or consumer. This warranty does not cover light bulbs or the xture
becoming damaged due to misuse, accidental damage, improper handling and/or installation, and
specically excludes liability for direct, incidental, or consequential damages. As some states do not allow
exclusions or limitations on an implied warranty, so the above exclusions and limitations may not apply.
This warranty gives you specic rights and you may also have other rights that vary from state to state.
Forced switch operation principle (In the case of power failure or the photocell is stuck on):
Operate the switch within 4 seconds, ON (1st time) - OFF (1st time) - ON (2nd time) - OFF (2nd time) -
ON (3rd time), enter Strong open state, press again to enter OFF (3rd time). This cycle, repeated again
and again.
If the user does not know which step the xture is in, shut it down, stay for half a minute, perform
the above operation on the switch, and reach ON (3rd time) to enter the strong opening.
NOTE:
minimum of 4 feet off the ground, and should
be located at least 20 inches below any
overhang.
This xture should be mounted a
□
□
FCC responsible party name: The Home Depot/address: 2455 Paces Ferry Road Atlanta,Georgia 30339
/Telephone number: (770) 433-8211.