Installation Guide
THANK YOU
to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Commercial Electric!
USE AND CARE GUIDE
LED FLAT PANEL FIXTURE
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
SKU# 305 543 508
SKU# 1003 382 575
Model #PN324A50A1-40
Ceiling
210*290mm
A side
B side
A side
B side
2
Table of Contents
Table of Contents ................................... 2
Safety Information .................................. 2
Warranty .......................................... 2
Pre-Installation ..................................... 3
Tools Required .................................... 3
Hardware Included ................................. 3
.................................
3
Installation
Specification
......................................
4
Safety Information
For your safety, always remember to:
□ Turn off the power supply at the fuse or circuit breaker box
before you install the fixture.
□ Ground the fixture to avoid potential electric shocks and to
ensure reliable starting.
□ Double-check all connections to be sure they are
tight and correct.
□ Wear rubber soled shoes and work on a sturdy
wooden ladder.
□ Account for small parts and destroy packing material, as these
may be hazardous to children.
This fixture is designed for use in a circuit protected by a fuse or
circuit breaker. It is also designed to be installed in accordance with
local electrical codes. If you are unsure about your wiring, consult a
qualified electrician or local electrical inspector, and check your local
electrical code.
WARNING: RISK OF SHOCK. House electric current can
cause painful shock or serious injury unless handled properly.
CAUTION: Turn off the main power at the circuit breaker
before installing the fixture, in order to prevent possible shock.
NOTICE: All electrical connections must be in accordance with local
and National Electrical Code (N.E.C.) standards. If you are unfamiliar
with proper electrical wiring connections obtain the services of a
qualified electrician.
Remove the fixture and the mounting package from the box and make
sure that no parts are missing by referencing the illustrations on the
installation instructions.
FCC STATEMENT
-This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation
between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an
experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacture could void the user’s authority to operate the equipment.
Warranty
LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials for up to 5 years from date of purchase. If it fails to do so,
please contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.
3 HOMEDEPOT.COM
Please contact 1-877-527-0313 for further assistance.
Pre-Installation
Specication
TOOLS REQUIRED HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part Description Quantity
EE Wire Nuts 3
Phillips
screwdriver
EE
Power Drill
4
Recessed Installation
Recessed Installation
1
Remove the LED at panel xture from
the package. Ensure that the power is
turned off before installing the xture.
2
Fold the 4 pieces of T-Gird clips as
picture shows.
3
Place the LED at panel xture into ceiling
and ensure the power supply is off.
4
Fix the at panel xture on the T bar grid
in the ceiling by twisting 4 pcs of T bar
grid clips onto the bar.
5
Remove the cover of junction box on the
back of the xture with a screwdriver.
Remove the knockouts on the A and B
side with a screwdriver.
6
Connect the electrical wires from the
power supply to the LED Flat panel
xture power supply, and 0-10V dimmer.
7
Attach the junction box cover plate
on the LED Flat Panel xture with the
screw using a screw driver. Turn on
the power supply.
□
0-10V dimmer connection：Connect the two 0-10V dimming
wires (purple+ and gray-) through knockout (B side shown as
below FIG 6) and connect with compatible 0-10V dimmer.
□
Connect the three supply wires (black - hot, white - neutral,
and green - ground) coming from LED Flat panel xture
junction box to the electrical power supply same color
wires through exible conduit and knockout with wire
nuts(EE) (A side shown as below FIG 6).
Model No. Volts (V) Frequency (HZ) Watts (W)
PN324A50A1-40 120V-277V 50/60 50
Current (mA)
420
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.