Full Product Manual
THANK YOU
to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Commercial Electric!
USE AND CARE GUIDE
LINKABLE LED STRIP LIGHT
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
SKU# 1005 002 271
Model # WS-WR2A50A1-40
2
Table of Contents
Table of Contents ................................... 2
Safety Information .................................. 2
Warranty .......................................... 2
Pre-Installation ..................................... 3
Tools Required .................................... 3
Hardware Included ................................. 3
.................................
3
Surface Installation
Specification
...............................
4
Linking Feature
..................................
7
Safety Information
For your safety, always remember to:
□ Turn off the power supply at the fuse or circuit breaker box
before you install the fixture.
□ Ground the fixture to avoid potential electric shocks and to
ensure reliable starting.
□ Double-check all connections to be sure they are
tight and correct.
□ Wear rubber soled shoes and work on a sturdy
wooden ladder or berglass ladder.
□ Account for small parts and destroy packing material, as these
may be hazardous to children.
WARNING: RISK OF SHOCK. House electric current can
cause painful shock or serious injury unless handled properly.
Connect up to a maximum of 6 strip lights. Do not exceed
270 total watts for interconnected lights.
CAUTION: Turn off the main power at the circuit breaker
before installing the fixture, in order to prevent possible shock.
NOTICE:
NOTICE:
All electrical connections must be in accordance with local
and National Electrical Code (N.E.C.) standards. If you are unfamiliar
with proper electrical wiring connections obtain the services of a
qualified electrician.
Remove the fixture and the mounting package from the box and make
sure that no parts are missing by referencing the illustrations on the
installation instructions.
FCC STATEMENT
-This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warranty
LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials for up to 5 years from date of purchase. If it fails to do so,
please contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.
3 HOMEDEPOT.COM
Please contact 1-877-527-0313 for further assistance.
Pre-Installation
Specication
TOOLS REQUIRED HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Phillips
screwdriver
Power Drill
4
Surface Installation
Model No. Volts (V) Frequency (HZ) Watts (W)
WS-WR2A50A1-40 120V-277V 60 45
Current (mA)
380
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.
210*290mm
1
Remove the LED strip xture from the package. Ensure that the power is turned
off before installing the xture.
2
Separating the part(A) from xture body (B).
3
Mark the two hole mounting positions of the xture body (B) on the ceiling. Drill a
hole in the ceiling for each of the two mounting holes.
4
Install a drywall anchor (AA) in each drilled mounting hole.
Part DescriptionImage Quantity
AA
BB
CC
DD
EE
FF
Drywall Anchor
Mounting Screw
Mounting Screw
Wire Nut
Serpentine Joint
Combined Bracket
2
2
2
3
1
1
5
Surface Installation
5
Feed the electrical wires from the electrical junction box through the octagonal
plate. Secure the octagonal plate (included in the package) to the junction box with
the mounting screw (BB).
6
Using a screwdriver punch out one of the knock out in the xture body (B) for
wiring.
7
Secure the xture housing to the ceiling with the mounting screw (CC).
6
Surface Installation
8
Connect the electrical wires from the power supply to the LED Strip xture power supply.
Remove the wire nuts attached on the three supply wires from the LED Strip xture.
Connect the three supply wires (black-hot, white-neutral,and green-ground) from
LED Strip xture to the same color wires from the electrical power supply through
knockout with the wire nuts (DD).
9
Hang on the security line.
7
Surface Installation
Linking Feature
Linking Feature
10
Attach the connectors.
11
Snap the part (A) onto the xture body (B)
Risk OF ELECTRIC SHOCK. Disconnect power to the strip light before linking additional strip lights.
WARNING:
□
Multiple light xtures can be connected, but only the rst light xture needs to be direct wired to an electrical box.
□
□
□
□
Remove the side cover (C) from one end of each body that will be linked.
First pull connecters through end cap opening, then pull connectors through rectangular opening in snap in bracket (FF).
Connect the connectors(D,E).
Firmly connect the combined bracket (FF) to one end of each body that will be linked.
□
Using a screwdriver punch out one of the
knock out in the xture body (B) for wiring.
□
Unscrew the serpentine joint (EE).Mount
the end of the thread to the xture body,
then fastening the screw nut.
□
Feed the metal hose (not included in the
package) through the serpentine joint, fastening
the two screws. After that the wire can be feed
through the metal hose for wiring.
Provide power to the xtures only after all linking connections have been made.
WARNING:
WARNING:
8
Connect up to a maximum of 6 strip lights. Do not exceed 270 total watts for interconnected lights.
B
B
B
B
B
D
E
C
FF
0-10V Dimming Schematic
WARNING: Refer to local and national electrical codes
for correctly sizing wire gauge and making the proper
electrical connections and ground connections to prevent
electrical shock and risk of re. Installation requires
knowledge of luminaires and electrical systems. If not
qualied, do not attempt installation. Contact a qualied
licensed electrician, to ensure wiring is correct and in
compliance of local codes.
gray
0-10 Volt Dimmer
(Supplied by others)
Lighting Fixture,
0-10v dimming LED
Driver
Lighting Fixture,
0-10v dimming LED
Driver
gray
purple
purple
Ground-green
Ground-green
Ground-green
Neutral
N
white
black
gray
purple
N
white
black
Line Black
Red/white
Red
REMARK:
Please reference the dimmers manufacturer wiring diagrams for correct wiring of 0-10 Volt Dimmer.
CAUTION:
Bracket edges
are sharp, wear gloves to
help avoid
cuts during
installation of xture.
STRIP LIGHT
If the single strip light need to connect electric wire through prole, it need to use the Serpentine Joint (EE).
NOTICE:
FCC compliance information is listed as below:
Responsible party: Leedarson America, Inc.
Responsible party address: 300 Technology Court SE Suite 100, Smyrna, GA 30082
Telephone number: (678) 293-8382
THIS FIXTURE IS DESIGNED FOR USE IN A CIRCUIT PROTECTED BY A
FUSE OR CIRCUIT BREAKER.THIS PRODUCT MUST BE INSTALLED BY
A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF
THE PRODUCT AND THE HAZARDS INVOLVED. IN ACCORDANCE WITH
THE APPLICABLE INSTALLATION CODE.
KEEP THESE INSTALLATION INSTRUCTIONS.
NOTE 1(for 277V input) : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
NOTE 1(for 120V input): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
B
B
B
B
EE
EE
Metal hose
A