Data Sheet

3 CORPORATE DRIVE
|
DANBURY, CONNECTICUT 06810
|
USA
|
T: 203.796.5300
|
F: 203.796.5303
|
TECH SUPPORT: 1.888.678.9427
|
[e-mail]
8 TURNBERRY PARK ROAD
|
GILDERSOME
|
MORLEY
|
LEEDS, UK LS27 7LE
|
T: [phone]
|
F: [phone]
|
[e-mail]
SPECIFICATIONS
ORDERING INFORMATION
FEATURES
› Utilizes two C1PS power supply modules in a fault-tolerant /
redundant configuration
› Automatic electronic current limiting feature
› Failure relay (NO) for local or remote loss of power indication
› Audio alarm in the event of power supply failure
› Voltage transient protection on all power and signal input/
output lines provides unconditional protection from power
surges and other voltage transient events.
› (12) twelve 1-inch rack slots available
› All modules located within the chassis rack are hot-swappable
› Lifetime Warranty
The C2 incorporates two C1PS Power Supply units that provide redundancy in
the unlikely event of a power supply failure. Two AC line cords (one per power
supply module) are provided, allowing each supply to be connected to a separate
uninterruptible power supply, providing the highest level of reliability in mission-critical
applications. An audio alarm provides an aural indication in the event that one of two
power supply modules has failed. The design approach employed by ComNet for
equipment mounted within the model C2 chassis rack unit with two modular C1PS
power supplies, provides for the elimination of a single-point failure in the event of
a major fault within any module located within the chassis rack. This is accomplished
through the use of automatic electronic current limiting within each rack-mountable
module, rather than providing the current limiting within the power supply unit which
supports the power requirements for equipment located within the rack. In nearly all
competing designs, a major fault within a module, located within the chassis rack, results
in the power supply unit going into a current limiting condition, and as a result, all of
the modules within the rack shut down. The C2 rack design employed by ComNet
eliminates this possibility, as only the faulty module shuts down, and the operation of
the other modules within the rack continue unimpaired. This automatic current limiting
feature is also self-resetting, should the fault or overload be of a temporary or intermittent
condition. Furthermore, all modules located within the chassis rack are hot-swappable, so
that it is not necessary to power-down the rack when removing or replacing modules.
C2
Rack Mount Card Cage With Redundant Power Supply
Electrical
Input Voltage 90-264 VAC @ 70 W Maximum
Output Voltage 9 VDC +/- 5% @ 6.5 Amps @ 75˚C
Fusing 1.25 A slow blow (rack power supply)
Plug-in modules individually electronically fused.
Each power supply unit is individually fused.
Power Indicator Red LED
AC Line Cord (2) Detachable, IEC-connected. Allows easy field
replacement or exchange for various worldwide AC
power plug configurations.
Mechanical
Size (L × W × H)
Rack Mount: 19.0 × 7.5 × 6.9 in. (48.2 × 19 × 17.5 cm)
Rack Slots: (12) 1-inch slots available
Shipping Weight: <5 lbs./2.15 kg
Environmental
MTBF >100,000 hours
Operating Temp -40˚ C to +75˚ C
Storage Temp -40˚ C to +85˚ C
Heat Generation 240 BTU
AGENCY COMPLIANCE
*
*Power Supply Only
In a continuing effort to improve and advance technology, product
specifications are subject to change without notice.
Part Number Description
C2-US 19” Rack (US AC Power Cord)
C2-EU 19” Rack (EU & UK Power Cord)
C2-IN 19” Rack (US, EU, UK & AU Power Cord)
C2-CH 19” Rack (no power supply)
C1PS
Spare 90-264 VAC Input Power Supply
(order power cords separately)
Included Accessories 90-264 VAC Input (includes 2 power supplies and 2 power cords)
Included with C2-US, C2-EU and C2-IN only
Options C1-BP – Blank Panel (1”)
C1-BP2 – Blank Panel (2”)
C1-BP3 – Blank Panel (3”)
C1-SA – South African Power Cord
C1-AU – Australian Power Cord