Installation Manual

ManualsBrandsComnet ManualsFiber Optic Transmission100 Mbps Ethernet Media Converter with PoE

INS_CNFE2MCPOE[/M]_REV–

07/28/10

PAGE 1

INSTALLATION AND OPERATION MANUAL

CNFE2MCPOE[/M]

10/100 MBPS 2 PORT MEDIA CONVERTER

WITH POWER OVER ETHERNET

The ComNet CNFE2MCPOE Ethernet 2 port media converter is designed to transmit

and receive 10/100 Mbps data over optical fiber through user selectable SFP

modules. These models require the ordering of sold-separately interchangeable SFP

modules for fiber type, distance and connectors.

The CNFE2MCPOE transmits and receives a single channel of Ethernet data. It also

supports IEEE 802.3at as Power Sourcing Equipment (PSE) with up to 30 Watts

output, both Mode A or Mode B are supported. The electrical interface will Auto-

Negotiate to a 10 Mbps, or 100 Mbps Ethernet rate without any adjustments.

The optical interface operates at a 100 Mbps Ethernet rate. It is environmentally

hardened to operate in extreme conditions.

LED indicators are provided for confirming equipment operating status. See Figure

10 on Page 5 for LED indicator descriptions.

See Figures 1 – 11 for complete installation details.

The CNFE2MCPOE operates as a standalone module. It can also be mounted in a

ComNet Rack, but PoE operation is not supported in this application. See Page 6 for

mounting instructions.

This manual serves the following

ComNet Model Numbers:

CNFE2MC POE/M

CNFE2MC POE

CNFE2MC POE2

Summary of content (6 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL CNFE2MCPOE[/M] 10/100 MBPS 2 PORT MEDIA CONVERTER WITH POWER OVER ETHERNET This manual serves the following ComNet Model Numbers: CNFE2MCPOE/M CNFE2MCPOE CNFE2MCPOE2 The ComNet CNFE2MCPOE Ethernet 2 port media converter is designed to transmit and receive 10/100 Mbps data over optical fiber through user selectable SFP modules. These models require the ordering of sold-separately interchangeable SFP modules for fiber type, distance and connectors.
PAGE 2
INSTALLATION AND OPERATION MANUAL CNFE2MCPOE[/M] FIGURE 1 – CNFE2MCPOE/M SMALL SIZE MEDIA CONVERTER CAT5e/6 OPTICAL FIBER DETERMINED BY SELECTION OF SFP MODULE BLACK BLACK WITH WHITE STRIPE Power: 12VDC @ 3A, 24VDC@1.5A FIGURE 2 – CNFE2MCPOE/M FRONT PANEL REAR PANEL FIGURE 3 – SWITCH POSITIONS Power over Ethernet is controlled by a switch based on fiber link. SW1 ON OFF TECH SUPPORT: 1.888.678.
PAGE 3
INSTALLATION AND OPERATION MANUAL CNFE2MCPOE[/M] FIGURE 4 – CNFE2MCPOE COMFIT MEDIA CONVERTER CAT5e/6 OPTICAL FIBER DETERMINED BY SELECTION OF SFP MODULE BLACK BLACK WITH WHITE STRIPE Power: 12VDC @ 3A, 24VDC@1.5A NOTE: Remove Electrical Connector for Rack Mount Units. PoE is not supported when mounted within ComNet rack. FIGURE 5 – MEDIA CONVERTER FRONT PANEL REAR PANEL FIGURE 6 – SWITCH POSITIONS Power over Ethernet is controlled by a switch based on fiber link. SW1 ON OFF TECH SUPPORT: 1.888.
PAGE 4
INSTALLATION AND OPERATION MANUAL CNFE2MCPOE[/M] FIGURE 7 – CNFE2MCPOE2 2-SWITCH COMFIT MEDIA CONVERTER CAT5e/6 OPTICAL FIBER DETERMINED BY SELECTION OF SFP MODULE BLACK BLACK WITH WHITE STRIPE Power: 12VDC @ 3A, 24VDC@1.5A NOTE: Remove Electrical Connector for Rack Mount Units. PoE is not supported when mounted within ComNet rack. FIGURE 8 – CNFE2MCPOE2 FRONT PANEL FIGURE 9 – SWITCH POSITIONS REAR PANEL Power over Ethernet is controlled by a switch based on fiber link.
PAGE 5
INSTALLATION AND OPERATION MANUAL CNFE2MCPOE[/M] FIGURE 10 – LED INDICATORS LINK PSE1 or PSE2 POWER GREEN Fiber interface linked (when lit or flashing) Power is being supplied by unit Unit powered up OFF Fiber interface not linked. Power not supplied by unit. (No PoE device) Unit powered down FIGURE 11 – POSSIBLE ETHERNET CONFIGURATION Ethernet IEEE 802.3 Network Element determined by user. Ethernet IEEE 802.
PAGE 6
INSTALLATION AND OPERATION MANUAL CNFE2MCPOE[/M] INSTALLATION CONSIDERATIONS Th CNFE2MCPOE is supplied as a Rack Mount/Surface mount module. In the ComNet Rack, PoE operation is not supported. The CNFE2MCPOEM is supplied as a Surface mount module. Units should be installed in dry locations protected from extremes of temperature and humidity. WARNING: Unit is to be used with a Listed Class 2 power supply.